In order to detect blockages in the pressurized fuel filter, the ECM determines if the fuel pressure of the common rail has deviated from the target value every 5000 km. If the average value of the judgment values recorded every 5000 km exceeds the threshold, a blockage is determined to be occurring in the pressurized fuel filter and a DTC is stored.
Also, at the same time, a message is displayed on the multi-information display and engine output is limited. The message on the multi-information display disappears after clearing the DTC.
| *1 | Fuel Supply Pump Assembly | *2 | Pressurized Fuel Filter |
| *3 | Fuel Filter Element Assembly | *4 | Fuel Tank |
| *5 | to Common Rail Assembly | *6 | from Injector Assembly |
|
High Pressure Fuel |
|
Feed Fuel |
|
Suction Fuel |
|
Return Fuel |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P00BB00 | Fuel Injector Insufficient Flow - Forced Limited Power | The average judgment value of the fuel pressure deviation state every 5000 km exceeds the threshold (1 trip detection logic). | ·
Fuel filter cap with element ·
Fuel filter element assembly |
Does not come on*
*: The multi information display illuminates. |
DTC stored | SAE Code: P00BB |
| DTC No. | Data List |
|---|---|
| P00BB00 | ·
Fuel Pressure (High) ·
Target Fuel Pressure (High) |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P00BB00 | Idling for 1 second or more |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
DTC P00BB00 is output.
When DTC P00BB00 is output, the fuel filter cap with element needs to be replaced. In order to inspect the fuel filter element assembly for blockages, do not perform replacement at this stage.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the clogging switch connector from the fuel filter element assembly.
Start the engine and warm it up.
Connect a circuit tester to the clogging switch.
Check that the clogging switch does not turn OFF (10 kΩ or higher) when revving the engine up from idling.
If the clogging switch turns OFF, it can be determined that the fuel filter element assembly is becoming clogged.
The clogging switch does not change from ON (below 1 Ω) when revving the engine up from idling.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the fuel filter cap with element.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER (for Cylinder Block Side)>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Clearing the DTCs turns off the message in the multi-information display.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel filter element assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT