Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL FILTER (for Cylinder Block Side)
RM35X0E _51 Engine / Hybrid System _079306 1GD-FTV FUEL _0385716 FUEL FILTER(for Cylinder Block Side) A

1GD-FTV FUEL  FUEL FILTER(for Cylinder Block Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:

When replacing the fuel filter element with cap, clean the fuel filter assembly and remove dirt completely.


PROCEDURE

Hide 2.REMOVE FUEL FILTER CAP WITH ELEMENT

a.
A439068

Disconnect the crankshaft position sensor connector and remove the 2 bolts.


b.

Detach the 3 clamps and disconnect the engine wire.


c.
A439069

Remove the union bolt and gasket, disconnect the No. 4 fuel pipe sub-assembly from the fuel filter assembly.


d.
A339675

Remove the 2 fuel pipe clamps from the No. 3 fuel pipe and fuel filter assembly.


e.
A339635

Remove the union bolt and gasket, disconnect the No. 3 fuel pipe from the fuel filter assembly.


f.
A339676

Remove the 2 nuts and disconnect the fuel filter assembly from the cylinder block sub-assembly.


g.
A339637

Using a 5 mm hexagon wrench, remove the 4 screws and fuel filter cap with element from the fuel filter assembly.

HINT:

Use a container to catch the draining fuel.



h.
A339638

Remove the O-ring from the fuel filter assembly.


Hide 3.INSTALL FUEL FILTER CAP WITH ELEMENT

a.

Clean the fuel filter assembly and remove dirt completely.


b.

Apply a light coat of diesel fuel to a new O-ring.


c.

Install the O-ring to the fuel filter assembly.


d.

Temporarily install a new fuel filter element with cap to the fuel filter assembly with the 4 screws.


e.
A362715E01
0.722,3.118 0.879,3.280 0.158,0.162 10 1 2.589,1.99 2.746,2.152 0.158,0.162 10 2 0.719,1.981 0.877,2.143 0.158,0.162 10 3 2.589,3.139 2.747,3.302 0.158,0.162 10 4

Using a 5 mm hexagon wrench, tighten the 4 screws in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Check the torque of screw 1 after tightening screw 4.



f.

Connect the fuel filter assembly to the cylinder block sub-assembly with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


g.

Connect the No. 3 fuel pipe and a new gasket to the fuel filter assembly with the union bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Clean the union bolt and remove dirt completely.



h.
A339639C02
1.792,3.063 2.229,2.771 2.229,2.771 2.365,2.771 true 2.417,2.688 2.667,2.865 0.25,0.177 10 true *a 1.427,2.573 1.667,2.771 0.24,0.198 10 true *b 1.823,2.583 2.063,2.781 0.24,0.198 10 true *b
*a Paint Mark
*b 0 to 2 mm (0 to 0.0787 in.)


Install the 2 fuel pipe clamps to the fuel filter assembly and No. 3 fuel pipe.

NOTICE:

Be careful that the fuel pipe clamp and No. 4 fuel pipe sub-assembly do not interfere with each other.


HINT:

Make sure the fuel pipe clamp is oriented as shown in the illustration.



i.

Install the No. 4 fuel pipe sub-assembly and a new gasket with the union bolt to the fuel filter assembly.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


j.
A439068N01
3.063,0.469 3.24,0.646 0.177,0.177 10 true A 1.948,0.167 2.156,0.365 0.208,0.198 10 true B

Attach the 3 clamps and connect the engine wire with the 2 bolts.

Torque:
for bolt A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for bolt B : 18.5 N*m (189 kgf*cm, 14 ft.*lbf)


k.

Connect the crankshaft position sensor connector.