The mass air flow meter sub-assembly is a sensor that measures the intake air volume using the following built-in components:
By-pass duct (allows some of the intake air to flow past a silicon chip sensor)
Silicon chip sensor (uses a heater control bridge circuit and temperature sensor bridge circuit to detect the difference in the temperature of the intake air that passes the sensors positioned before and after the heater)
Control circuit (converts the difference in temperature into a pulse signal and performs correction)
Intake air flows past the temperature sensor (before heater), the heater, and then the temperature sensor (after heater) of the silicon chip sensor in the by-pass duct. As the intake air is warmed up when it is exposed to the heater, the temperature of the intake air as it flows past the temperature sensor (after heater) is higher than when it flows past the temperature sensor (before heater). The difference in temperature of the intake air at each temperature sensor varies depending on the velocity of the intake air that flows past the silicon chip sensor. The temperature sensor bridge circuit detects the difference in temperature and the control circuit converts it into a pulse signal and outputs it to the ECM. When the temperature detected by the temperature sensor (before heater) is higher than that detected by the temperature sensor (after heater), backflow of the intake air is detected.
The ECM calculates the intake air volume based on the pulse signal received from the mass air flow meter sub-assembly.
The heater control bridge circuit has a temperature sensor and power transistor, and maintains the heater temperature at a specific temperature.
| *1 | Mass Air Flow Meter Sub-assembly | - | - |
| *a | Silicon Chip Sensor | *b | By-pass Duct |
| *c | Heater | *d | Heater Thermistor |
| *e | Intake Air | *f | Temperature Sensor (After Heater) |
| *g | Temperature Sensor (Before Heater) | *h | Air Flow |
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P010012 | Mass or Volume Air Flow Sensor "A" Circuit Short to Battery | Mass air flow meter sub-assembly signal frequency is higher than 9.8 kHz for 3 seconds (1 trip detection logic). | ·
Open or short in mass air flow meter sub-assembly circuit ·
Mass air flow meter sub-assembly ·
ECM |
Class A | DTC stored | SAE Code: P0103 |
| P010014 | Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open | Mass air flow meter sub-assembly signal frequency is less than 0.1 kHz for 3 seconds (1 trip detection logic). | ·
Open or short in mass air flow meter sub-assembly circuit ·
Mass air flow meter sub-assembly ·
ECM |
Class A | DTC stored | SAE Code: P0102 |
| DTC No. | Data List |
|---|---|
| P010012
P010014 |
Mass Air Flow Sensor |
If DTC P010012 or P010014 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is less or more air than the actual intake air amount, EGR is decreased according to the target EGR):
Combustion noise worsens
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P010012
P010014 |
3 seconds or more after engine is started |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly) |
Disconnect the mass air flow meter sub-assembly connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E20-3 (5V) - Body ground | Engine switch on (IG) | 4.8 to 5.2 V |
| E20-1 (FG) - E20-2 (E2G) | Engine switch on (IG) | 4.8 to 5.2 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P010012 or P010014 is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E20-3 (5V) - E6-30 (VCVG) | Always | Below 1 Ω |
| E20-1 (FG) - E6-31 (VG) | Always | Below 1 Ω |
| E20-2 (E2G) - E6-29 (EVG) | Always | Below 1 Ω |
| E20-3 (5V) or E6-30 (VCVG) - Body ground and other terminals | Always | 10 kΩ or higher |
| E20-1 (FG) or E6-31 (VG) - Body ground and other terminals | Always | 10 kΩ or higher |
| E20-2 (E2G) or E6-29 (EVG) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and wait for 3 seconds or more.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT