Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECM › 2019.06–2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0387390 ECM A

1GD-FTV ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the ECM removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
ECM
·

Learning values save

·

Learning values write

·

Perform Vehicle Identification Number (VIN) or frame number registration


DTC is stored w/ DPF:
(Click here)
w/ Urea SCR System:
(Click here)
w/ EGR Cooler:
(Click here)
w/ Exhaust Gas Temperature Sensor for EGR:
(Click here)
w/o EGR Cooler:
(Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
for RC60J:

Performing iMT installation information reset


·

iMT system

·

DTCs are output


(Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative when not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative when not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



NOTICE:
·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) registration when replacing the ECM.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 55320 3.REMOVE LOWER NO. 2 INSTRUMENT PANEL ASSEMBLY

Hide 89661 4.REMOVE ECM

a.
A443199

for LHD:

i.

Disconnect the 6 connectors from the ECM.


ii.

Remove the bolt, nut and ECM.



b.
A443201

for RHD:

i.

Disconnect the 6 connectors from the ECM.


ii.

Remove the bolt, nut and ECM.



Hide 89667E 5.REMOVE NO. 1 ECM BRACKET

a.
A443200

for LHD:

i.

Remove the 2 screws and No. 1 ECM bracket from the ECM.



b.
A443203

for RHD:

i.

Remove the 2 screws and No. 1 ECM bracket from the ECM.



Hide 89668 6.REMOVE NO. 2 ECM BRACKET

a.
A443202

for LHD:

i.

Remove the 2 screws and No. 2 ECM bracket from the ECM.



b.
A443204

for RHD:

i.

Remove the 2 screws and No. 2 ECM bracket from the ECM.