The manifold absolute pressure sensor detects the intake manifold pressure. The ECM determines the basic injection volume and injection advance timing based on the voltage output by the manifold absolute pressure sensor.
The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa [0 mmHg, 0 in.Hg]).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P010512 | Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Short to Battery | Manifold absolute pressure sensor voltage is 4.8 V or higher for more than 0.5 seconds (1 trip detection logic). | ·
Open or short in manifold absolute pressure sensor circuit ·
Manifold absolute pressure sensor ·
ECM |
Class A | DTC stored | SAE Code: P0108 |
| P010514 | Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Short to Ground or Open | Manifold absolute pressure sensor voltage is 0.1 V or less for more than 0.5 seconds (1 trip detection logic). | ·
Open or short in manifold absolute pressure sensor circuit ·
Manifold absolute pressure sensor ·
ECM |
Class A | DTC stored | SAE Code: P0107 |
| DTC No. | Data List |
|---|---|
| P010512
P010514 |
·
Intake Manifold Absolute Pressure ·
Atmospheric Pressure |
If DTC P010512 and/or P010514 is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
When DTC P010512 or P010514 is stored, check the intake manifold pressure by entering the following menus: Powertrain / Engine and Transmission / Data List / Intake Manifold Absolute Pressure.
| GTS Displayed | Malfunction |
|---|---|
| 23 kPa (173 mmHg, 6.79 in.Hg) | ·
Open in VC circuit ·
Open in PIM circuit ·
Short in PIM circuit |
| 418 kPa (3135 mmHg, 123.44 in.Hg) | ·
Open in E circuit |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P010512
P010514 |
2 seconds after engine is started, race engine for 1 second |
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Intake Manifold Absolute Pressure.
| Tester Display |
|---|
| Intake Manifold Absolute Pressure |
Read the value.
Same as the actual atmospheric pressure.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).
Also, check "Atmospheric Pressure" in the Data List.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Manifold Absolute Pressure Sensor) |
Disconnect the manifold absolute pressure sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E40-3 (VC) - E40-1 (E) | Engine switch on (IG) | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E5-18 (PIM) - E5-19 (EPIM) | Engine switch on (IG) | 0.8 to 1.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the manifold absolute pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E40-2 (PIM) - E5-18 (PIM) | Always | Below 1 Ω |
| E40-1 (E) - E5-19 (EPIM) | Always | Below 1 Ω |
| E40-2 (PIM) or E5-18 (PIM) - Body ground and other terminals | Always | 10 kΩ or higher |
| E40-1 (E) or E5-19 (EPIM) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the manifold absolute pressure sensor connector.
| *a | Front view of wire harness connector
(to Manifold Absolute Pressure Sensor) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E40-3 (VC) - E40-2 (PIM) | Engine switch off | No short or no open circuit |
| E40-2 (PIM) - E40-1 (E) | Engine switch off | No short or no open circuit |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the manifold absolute pressure sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E5-28 (VCPM) - E5-19 (EPIM) | Engine switch on (IG) | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
NG
OK
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the engine switch off for 30 seconds or more.
Turn the GTS off.
Turn the engine switch on (IG) for 3 seconds and turn the GTS on.
After the engine is started for 2 seconds, race the engine for 1 second.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and Transmission / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P010512 or P010514.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE, race the engine for 1 minute, and then idle the engine for 5 minutes.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT