Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P034011  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground  P034015  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P03402A.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>P03402A

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P034011 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground Output voltage of camshaft position sensor is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Camshaft position sensor

·

Open or short in camshaft position sensor circuit

·

ECM


Class A DTC stored SAE Code: P0342
P034015 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open Output voltage of camshaft position sensor is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Camshaft position sensor

·

Open or short in camshaft position sensor circuit

·

ECM


Class A DTC stored SAE Code: P0343

HINT:

If DTC P034011 or P034015 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




Reference: Inspection using an oscilloscope.

The correct waveform is as shown.

A340471E01
3.042,1.021 3.375,1.281 0.333,0.26 10 false GND 3.031,1.542 3.365,1.771 0.333,0.229 10 false GND 0.052,0.854 0.406,1.094 0.354,0.24 10 false G2 0.063,1.396 0.354,1.625 0.292,0.229 10 false NE 2.729,0.156 3.323,0.354 0.594,0.198 10 false 2 V/DIV. 1.292,1.833 2.5,2 1.208,0.167 10 false 20 msec./DIV.

ECM Terminal Name Between G2+ and G2-
Between NE+ and NE-
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

MONITOR DESCRIPTION

When the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P034011
P034015
Engine switch on (IG) for 4 seconds or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

d.

Record any output DTC(s).


e.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

f.

Turn the engine switch off for 30 seconds or more.


g.

Disconnect the camshaft position sensor connector.


h.

Turn the engine switch on (IG) for 4 seconds or more.


i.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

j.

Check whether the DTC changes when the connector is disconnected and connected.

Result:
Result Proceed to
DTC does not change A
DTC changes B




A

2.CHECK ECM (CAMSHAFT POSITION SENSOR VOLTAGE)

B

5.REPLACE CAMSHAFT POSITION SENSOR
2.CHECK ECM (CAMSHAFT POSITION SENSOR VOLTAGE)
a.
A372026C61
1.729,0.833 2.146,1.083 0.417,0.25 1.792,2.281 2.125,1.635 true 2.542,2.271 2.188,1.635 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.823,0.875 2.281,1.073 0.458,0.198 10 false E8 1.448,2.375 2.031,2.573 0.583,0.198 10 false 18 (G2-) 2.333,2.375 3.042,2.583 0.708,0.208 10 false 17 (VCG)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E8-17 (VCG) - E8-18 (G2-) Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

7.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E79-1 (G22+) - E8-27 (G2+) Always Below 1 Ω
E79-2 (G22-) - E8-18 (G2-) Always Below 1 Ω
E79-1 (G22+) or E8-27 (G2+) - Body ground and other terminals Always 10 kΩ or higher
E79-2 (G22-) or E8-18 (G2-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK ECM (CHECK RESISTANCE)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the camshaft position sensor connector.


b.
A186169C21
0.271,1.5 0.667,1.75 0.396,0.25 2.365,3.01 2,2.25 true 1.167,2.969 1.5,2.25 true 1.708,2.99 1.698,2.25 true 0.156,0.156 0.375,0.396 0.219,0.24 10 false *a 0.323,1.542 0.688,1.729 0.365,0.188 10 false E79 2.302,3.021 2.667,3.208 0.365,0.188 10 false VC 0.823,3 1.458,3.208 0.635,0.208 10 false G22+ 1.542,3.01 2.177,3.219 0.635,0.208 10 false G22-
*a Front view of wire harness connector
(to Camshaft Position Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E79-3 (VC) - E79-1 (G22+) Engine switch off No short or no open circuit
E79-1 (G22+) - E79-2 (G22-) Engine switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

5.REPLACE CAMSHAFT POSITION SENSOR

NG

7.REPLACE ECM
5.REPLACE CAMSHAFT POSITION SENSOR

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

e.

Turn the engine switch off for 30 seconds or more.


f.

Turn the engine switch on (IG) for 4 seconds or more.


g.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

h.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END