The exhaust gas temperature sensors are installed before and after the exhaust manifold converter sub-assembly to sense the exhaust gas temperature.
A thermistor built into the sensor changes its resistance value according to the exhaust gas temperature. The lower the exhaust gas temperature, the higher the thermistor resistance value. The higher the exhaust gas temperature, the lower the thermistor resistance value.
The exhaust gas temperature sensor is powered by a 5 V supply from the THTO, THCI and THCO terminals of the ECM, via resistor R.
Resistor R and the exhaust gas temperature sensor are connected in series. When the resistance value of the exhaust gas temperature sensor changes in accordance with the exhaust gas temperature, the voltage at terminals THTO, THCI and THCO also changes. The exhaust gas temperature sensor monitors the temperature upstream of the DOC catalyst. The No. 2 exhaust gas temperature sensor monitors the temperature upstream of the DPF catalyst. The No. 3 exhaust gas temperature sensor monitors the rise in temperature of the DPF catalyst. When PM forced regeneration is needed, the ECM operates the exhaust fuel addition injector assembly to obtain the target upstream temperature of the DPF catalytic converter as monitored through sensor 2. In addition, the ECM monitors the temperature increase of the exhaust manifold converter sub-assembly using sensor 3.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P054411 | Exhaust Gas Temperature Sensor 1 Bank 1 Circuit Short to Ground | Exhaust gas temperature sensor output voltage is below 0.2 V for 3 seconds or more when all conditions are met (1 trip detection logic): | ·
Open or short in exhaust gas temperature sensor circuit ·
Exhaust gas temperature sensor ·
ECM |
Class B2 | DTC stored | SAE Code: P0545 |
| P054415 | Exhaust Gas Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open | Exhaust gas temperature sensor output voltage is higher than 4.95 V for 3 seconds or more when all conditions are met (1 trip detection logic):
·
After starting the engine, 11 minutes or more elapses ·
Engine is running ·
Coolant temperature is 60°C (140°F) or higher |
·
Open or short in exhaust gas temperature sensor circuit ·
Exhaust gas temperature sensor ·
ECM |
Class B2 | DTC stored | SAE Code: P0546 |
| DTC No. | Data List |
|---|---|
| P054411
P054415 |
Exhaust Temperature B1S1 |
DTC P20CF00 (Exhaust fuel addition injector assembly malfunction) may be stored if there is an open malfunction in an exhaust gas temperature sensor circuit.
Sensor 1 represents the sensor located upstream of the DOC catalytic converter.
When DTC P054411 and P054415 is output, check the exhaust gas temperature indicated by "Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Exhaust Temperature B1S1" using the GTS.
| Condition | Exhaust Temperature B1S1 | Exhaust Gas Temperature Sensor Condition |
|---|---|---|
| Idling with warm engine | Constant at between 50 and 700°C (122 and 1292°F) | Normal |
| 0°C (32°F) | Open circuit | |
| 1000°C (1832°F) | Short circuit |
The ECM constantly monitors the output voltages from the exhaust gas temperature sensors in order to detect problems with the sensors. When the sensor output voltage deviates from the normal operating range (between 0.2 V and 4.95 V) for more than 3 seconds after the engine is warmed up, the ECM interprets this as malfunction of the sensor circuit and illuminates the MIL (MIL status: Class B2).
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P054411 | Engine switch on (IG) for 3 seconds or more |
| P054415 | Idle the engine for 3 seconds after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine. |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Exhaust Temperature B1S1.
| Tester Display |
|---|
| Exhaust Temperature B1S1 |
Read the value.
Same as the actual exhaust gas temperature (50 to 700°C [122 to 1292°F] during idling with warm engine), and varies after an engine speed of 3000 rpm is maintained for 1 minute.
| Temperature Displayed | Proceed to |
|---|---|
| 0°C (32°F) (After warming up the engine) | A |
| 1000°C (1832°F) or higher | B |
| Same as the actual exhaust gas temperature | C |
If there is a short circuit, the GTS will indicate 0°C (32°F).
If there is an open circuit, the GTS will indicate 1000°C (1832°F).
A
B
C
| *1 | Exhaust Gas Temperature Sensor |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Exhaust Gas Temperature Sensor) |
Disconnect the exhaust gas temperature sensor connector.
Connect terminals 1 (E2) and 2 (THC3) of the exhaust gas temperature sensor connector on the wire harness side.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Diesel Exhaust / Exhaust Temperature B1S1.
| Tester Display |
|---|
| Exhaust Temperature B1S1 |
Read the value.
1000°C (1832°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the exhaust gas temperature sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the exhaust gas temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E88-2 (THC3) - E5-23 (THTO) | Always | Below 1 Ω |
| E88-1 (E2) - E5-27 (E2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off for 30 seconds or more.
Start the engine and turn the GTS on.
Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Exhaust Gas Temperature Sensor |
| *2 | ECM |
Disconnect the exhaust gas temperature sensor connector.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Data List / Exhaust Temperature B1S1.
| Tester Display |
|---|
| Exhaust Temperature B1S1 |
Read the value.
0°C (32°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the exhaust gas temperature sensor.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the exhaust gas temperature sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E88-2 (THC3) or E5-23 (THTO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) for 3 seconds or more.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off for 30 seconds or more.
Start the engine and turn the GTS on.
Idle the engine for 3 seconds or more after warming up the engine (the engine coolant temperature is 60°C (140°F) or higher) and allowing 11 minutes to elapse after starting the engine.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT