Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR) › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0395991 ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Exhaust Gas Temperature Sensor for EGR)  P056014  System Voltage Circuit Short to Ground or Open  


DESCRIPTION

The battery supplies electricity to the ECM even when the engine switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the ECM memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL (MIL status: Class B1) and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P056014 System Voltage Circuit Short to Ground or Open The voltage at terminal BATT drops excessively for 3 seconds and part of the stored values in the ECM are initialized (1 trip detection logic).
·

Open in backup power source circuit (to BATT terminal)

·

Battery

·

Battery terminals

·

ECM


Class B1 DTC stored SAE Code: P0562

Related Data List
DTC No. Data List
P056014 Battery Voltage*

*: This is not the voltage at terminal BATT, it is the power supply voltage for the ECM.

HINT:

If DTC P056014 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P056014 Engine switch on (IG) for 3 seconds or more

WIRING DIAGRAM

A348990E12
0.896,1.844 1.5,2.073 0.604,0.229 10 false Battery 0.781,1.135 1.385,1.365 0.604,0.229 10 false FL MAIN 2.542,0.875 3.865,1.25 1.323,0.375 10 false EFI-MAIN 5.771,0.698 6.375,0.927 0.604,0.229 10 false BATT 5.792,1.635 6.396,1.865 0.604,0.229 10 false E1 2.677,0.531 2.813,0.76 0.135,0.229 10 false 1 2.917,0.531 3.052,0.76 0.135,0.229 10 false 2 5.427,0.719 5.75,1 0.323,0.281 10 false N2 5.479,0.49 5.615,0.719 0.135,0.229 10 false 1 5.49,1.448 5.625,1.677 0.135,0.229 10 false 5 5.438,1.635 5.76,1.917 0.323,0.281 10 false A2 6.031,2.24 6.635,2.469 0.604,0.229 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After the engine switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

2.CHECK BATTERY TERMINAL

NG

9.RECHARGE OR REPLACE BATTERY
2.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

3.CHECK ECM TERMINAL VOLTAGE (BATT)

NG

7.REPAIR OR REPLACE BATTERY TERMINAL
3.CHECK ECM TERMINAL VOLTAGE (BATT)
a.
A346513C14
2.292,0.292 2.688,0.563 0.396,0.271 2.135,1.719 2.677,0.958 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.802,1.76 2.635,1.969 0.833,0.208 10 false 1 (BATT) 2.396,0.354 2.781,0.594 0.385,0.24 10 false N2
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N2-1 (BATT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

d.

Turn the engine switch off.


e.

Turn the engine switch on (IG) for 3 seconds or more.


f.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

g.

Read the DTCs.

Result:
Result Proceed to
DTC P056014 is output A
No DTC is output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE BATTERY TERMINAL
a.

Repair or replace the battery terminal.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 456

c.

Turn the engine switch off for 30 seconds or more.


d.

Turn the engine switch on (IG) for 3 seconds or more.


e.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 456

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

9.RECHARGE OR REPLACE BATTERY
a.

Recharge or replace the battery.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED