Refer to DTC P208A14.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P204A1C | Reductant Pressure Sensor Circuit Range/Performance Circuit Voltage Out of Range | When the urea pump is not rotating (urea pump operation check complete and not being filled), the pressure sensor value is outside of a fixed range (1 trip detection logic). | Pressure sensor (urea pump) | Class A | DTC stored | SAE Code: P204B |
| DTC No. | Data List |
|---|---|
| P204A1C | Reductant Pressure |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P204A1C | Engine switch on (IG) for 5 seconds or more |
The urea injector set is a precision instrument. Take necessary precautions for installation and shipping. Do not use the part if it has been struck or dropped.
If the urea solution remaining inside the urea injector set dries out, it may become unable to inject urea solution. Therefore, conduct urea tube with heater assembly installation and removal quickly.
If the urea solution dries out and deposition occurs, urea may cling to the O-ring of the pipe and cause seal problems. Therefore, clean the urea tube with heater assembly and intake port of the urea injector set with water before attaching them.
Perform this procedure in an environment where urea solution will not freeze.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P204A1C is output | A |
| DTC P204A1C and other DTCs are output* | B |
*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.
A
B
Check around the bottom of the vehicle.
If the urea solution dries on an object, deposition occurs and leaves behind a white powder.
Area to check:
Areas connecting the urea pump and urea injector set.
Perforations in the urea tank sub-assembly.
Connectors not connected properly.
Clogging of the cooling fins of the urea injector set.
If the cooling fins are clogged with foreign matter, remove the foreign matter and clean the cooling fins.
Repair any trouble areas.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Pump Check (Backward).
| Tester Display |
|---|
| Reductant Pump Check (Backward) |
Perform the Active Test.
Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Purge / Data List / Diesel Exhaust / Reductant Pressure.
| Active Test Display |
|---|
| Reductant Purge |
| Data List Display |
|---|
| Reductant Pressure |
After executing the Active Test, check the Reductant Pressure.
Approximately 0 kPa
Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Filling (Pressure Keep) / Data List / Diesel Exhaust / Reductant Pressure.
| Active Test Display |
|---|
| Reductant Filling (Pressure Keep) |
| Data List Display |
|---|
| Reductant Pressure |
After executing the Active Test, check the Reductant Pressure.
Perform the Active Test until the pressure stabilizes (may take from 5 to 60 seconds).
400 to 600 kPa
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the urea pump.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) and turn the GTS on.
Wait for 5 seconds or more.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT