The urea pump is a bottom entry type intake pump installed to the bottom of the urea tank sub-assembly.
This urea pump has functions that 1) pressurize and supply the urea solution, 2) thaw frozen urea solution and heat the urea solution to prevent further freezing, 3) gauge the level of remaining urea solution inside the tank and 4) filter foreign matter inside the urea tank sub-assembly.
When the engine is stopped, the urea pump operates in reverse to draw the urea solution in the pipe back into the urea tank sub-assembly.
The urea pump performs feedback control using the pressure sensor, achieving accurate urea solution volume adjustment control.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P208A14 | Reductant Pump "A" Control Circuit Low Circuit Short to Ground or Open | When the urea pump motor is operating, an open or short circuit occurs in the urea pump motor circuit (1 trip detection logic). | ·
Open or short in urea tube with pump motor circuit ·
Urea pump ·
Urea pump control ECU |
Class A | DTC stored | SAE Code: P208C |
| P208A19 | Reductant Pump "A" Control Circuit High Circuit Current Above Threshold | When power is supplied to the urea pump (during normal/reverse operation, power supplied to heater, position fixed), the pump current is equal to or greater than a fixed value (1 trip detection logic). | Urea pump | Class A | DTC stored | SAE Code: P208D |
| P208A96 | Reductant Pump "A" Control Performance/Stuck Off Component Internal Failure | When each pump status is "operating" (operation check, filling, pressure increase, pressure maintenance, line pressure relief), urea pump rotation malfunctions, pressure malfunctions, etc., are detected multiple times (1 trip detection logic). | Urea pump | Class A | DTC stored | SAE Code: P208B |
| P20E900 | Reductant Pressure Too High | After filling the urea injector with urea solution from the urea pipe, the urea pressure is continuously higher than a fixed value (1 trip detection logic). | Urea pump | Class A | DTC stored | SAE Code: P20E9 |
| DTC No. | Data List |
|---|---|
| P208A14 | Reductant Pump Speed |
| P208A96
P208A19 P20E900 |
Reductant Pressure |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P208A14
P208A19 P208A96 P20E900 |
Idle engine for 5 second |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P208A14 is output | A |
| DTC P208A19, P208A96 or P20E900 is output | B |
| DTC P208A19, P208A96 or P20E900 and other DTCs are output* | C |
*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.
A
B
C
Disconnect the urea pump connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| x4-7 (PHAA) - N37-3 (UPMU) | Always | Below 1 Ω |
| x4-8 (PHAB) - N37-22 (UPMV) | Always | Below 1 Ω |
| x4-16 (PHAC) - N37-33 (UPMW) | Always | Below 1 Ω |
| x4-15 (MGND) - N37-23 (MSG) | Always | Below 1 Ω |
| x4-7 (PHAA) or N37-3 (UPMU) - Body ground and other terminals | Always | 10 kΩ or higher |
| x4-8 (PHAB) or N37-22 (UPMV) - Body ground and other terminals | Always | 10 kΩ or higher |
| x4-16 (PHAC) or N37-33 (UPMW) - Body ground and other terminals | Always | 10 kΩ or higher |
| x4-15 (MGND) or N37-23 (MSG) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Check around the bottom of the vehicle.
If the urea solution dries on an object, deposition occurs and leaves behind a white powder.
Area to check:
Areas connecting the urea pump and urea injector set.
Perforations in the urea tank sub-assembly.
Connectors not connected properly.
Clogging of the cooling fins of the urea injector set.
If the cooling fins are clogged with foreign matter, remove the foreign matter and clean the cooling fins.
Repair any trouble areas.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and idle it for 5 seconds or more.
Clear the DTCs.
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Pump Check (Backward).
| Tester Display |
|---|
| Reductant Pump Check (Backward) |
Perform the Active Test.
Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Purge.
| Tester Display |
|---|
| Reductant Purge |
Perform the Active Test.
Perform the urea solution forced purge to draw the urea solution back into the urea tank sub-assembly from the urea injector set.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output | A |
| DTC P208A19, P208A96 or P20E900 is output | B |
| DTC P208A14 is output | C |
A
B
C
Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Filling (Pressure Keep) / Data List / Diesel Exhaust / Reductant Pressure.
| Active Test Display |
|---|
| Reductant Filling (Pressure Keep) |
| Data List Display |
|---|
| Reductant Pressure |
Execute "Reductant Filling (Pressure Keep)
Check the Reductant Pressure.
400 to 600 kPa
During a malfunction, pressure either does not increase, or increases to 800 kPa or higher and then stops.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the urea pump.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and idle it for 5 seconds or more.
Clear the DTCs.
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and idle it for 5 seconds or more.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Confirm that the DTCs are not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the urea pump.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Start the engine and idle it for 5 seconds or more.
Clear the DTCs.
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Pump Check (Backward).
| Tester Display |
|---|
| Reductant Pump Check (Backward) |
Perform the Active Test.
Enter the following menus: Powertrain / Engine and Transmission / Active Test / Reductant Purge.
| Tester Display |
|---|
| Reductant Purge |
Perform the Active Test.
Perform the urea solution forced purge to draw the urea solution back into the urea tank sub-assembly from the urea injector set.
Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output | A |
| DTC P208A14 is output | B |
A
B
Replace the urea pump control ECU.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT