Home › Vehicle Interior › SEAT › REAR SEAT CUSHION HEATER › from 2019.06
RM35X0E _58 Vehicle Interior _078601 SEAT _0396332 REAR SEAT CUSHION HEATER A

SEAT  REAR SEAT CUSHION HEATER  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:
·

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear No. 1 seat cushion heater assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

The procedure listed below is a representative example.

·

Use the same procedure for first row and second row, unless otherwise specified.



PROCEDURE

Hide 1. PRECAUTION (for First Row)

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.



NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

If the pretensioner has been deployed, replace any damaged parts as necessary.



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for First Row)

a.

Operate the rear power seat switch and move the ottoman to the uppermost position and seatback to the frontmost position.


b.

Disconnet the cable from the negative (-) battery terminal.


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




Hide 72526J 4.REMOVE NO. 1 SEAT RECLINING ADJUSTER RELEASE HANDLE LH

Hide 72345Y 5.REMOVE LH SEAT NO. 1 SEAT NO. 1 STAND FRAME CAP

Hide 72890C 6.REMOVE LH SEAT NO. 1 SEAT ARMREST ASSEMBLY

Hide 71324R 7.REMOVE REAR NO. 1 SEAT CUSHION LH (for First Row)

Hide 71849L 8.REMOVE NO. 1 SEAT ADJUSTER COVER CAP LH

Hide 72C45 9.REMOVE LH SEAT NO. 1 SEAT NO. 3 STAND FRAME CAP (for First Row)

Hide 71844J 10.REMOVE REAR NO. 1 SEAT NO. 2 RECLINING COVER LH

Hide 72804E 11.REMOVE LH SEAT REAR NO. 1 SEAT ARMREST FRAME SUB-ASSEMBLY LH

Hide 78060C 12.REMOVE NO. 1 SEAT SIDE TABLE ASSEMBLY (for First Row, RH Side)

Hide 84923 13.REMOVE REAR POWER SEAT SWITCH

Hide 72840K 14.REMOVE REAR NO. 1 SEAT ARMREST ASSEMBLY LH

Hide 71848W 15.REMOVE LH SEAT NO. 1 SEAT ADJUSTER COVER CAP

Hide 71H74 16.REMOVE REAR SEAT LOWER CUSHION SHIELD LH (for Second Row)

Hide 71866D 17.REMOVE LH SEAT REAR NO. 1 SEAT COVER BEZEL

Hide 71826C 18.REMOVE REAR SEAT CUSHION MOULDING LH

Hide 66990E 19.REMOVE REAR NO. 1 SEAT CUP HOLDER ASSEMBLY LH

Hide 72803H 20.REMOVE LH SEAT REAR NO. 1 SEAT ARMREST FRAME SUB-ASSEMBLY RH

Hide 71H75R 21.REMOVE LH SEAT RECLINING ADJUSTER INSIDE COVER RH

Hide 73375 22.REMOVE REAR SEAT SHOULDER BELT COVER LH

Hide 72345Z 23.REMOVE LH SEAT NO. 1 SEAT NO. 2 STAND FRAME CAP

Hide 72046G 24.REMOVE LH SEAT NO. 1 SEAT NO. 2 TRACK COVER SUB-ASSEMBLY

Hide 73390 25.REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH (ANCHOR)

Hide 26.REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD

Hide 79959F 27.REMOVE NO. 1 SEAT LEG COVER LH

Hide 71H76N 28.REMOVE LH SEAT RECLINING ADJUSTER INSIDE COVER

Hide 79968W 29.REMOVE LH SEAT REAR NO. 1 SEAT LEG SIDE COVER

Hide 30.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD

Hide 79012A 31.REMOVE NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY LH

Hide 87510Y 32.REMOVE REAR NO. 1 SEAT CUSHION HEATER ASSEMBLY LH

a.
B553050

Remove the 17 tag pins and rear No. 1 seat cushion heater assembly LH.

NOTICE:

Be careful not to damage the No. 1 seat cushion cover sub-assembly LH and No. 1 seat cushion heater assembly LH.