Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
55990C
1.REMOVE CENTER DEFROSTER NOZZLE ASSEMBLY
|
Screw <A> |
Remove the 5 screws <A>.
Detach the guide and remove the center defroster nozzle assembly.
88051B
2.REMOVE NO. 1 ION GENERATOR SUB-ASSEMBLY (for Wagon, w/ Ion Generator)
87201N
3.REMOVE AIR DUCT SUB-ASSEMBLY (for Wagon, w/ Ion Generator)
Remove the air duct sub-assembly.
55843A
4.REMOVE NO. 1 HEATER TO REGISTER DUCT
|
Screw <A> |
Remove the 3 screws <A>.
Detach the guide and remove the No. 1 heater to register duct.
55845A
5.REMOVE NO. 3 HEATER TO REGISTER DUCT
|
Screw <A> |
Remove the 3 screws <A>.
Detach the guide and remove the No. 3 heater to register duct.
55844
6.REMOVE NO. 2 HEATER TO REGISTER DUCT
|
Screw <A> |
Remove the 4 screws <A>.
Detach the guide and remove the No. 2 heater to register duct.
7.REMOVE NAVIGATION ANTENNA ASSEMBLY WITH BRACKET (w/ Navigation Antenna)
86101
8.REMOVE ANTENNA CORD SUB-ASSEMBLY
89120A
9.REMOVE AUTOMATIC LIGHT CONTROL SENSOR (w/ Automatic Light Control System)
88625H
10.REMOVE COOLER (SOLAR SENSOR) THERMISTOR (w/o Automatic Light Control System)
55538C
11.REMOVE COOLER SWITCH HOLE COVER (w/ Cover)
|
Remove in this Direction |
Detach the claw and remove the cooler switch hole cover.
89747F
12.REMOVE BLIND SPOT MONITOR BUZZER (w/ Blind Spot Monitor System)
86681C
13.REMOVE ANTENNA DIVIDER (for Wagon, w/ Telematics Transceiver)
82144
14.REMOVE NO. 4 INSTRUMENT PANEL WIRE
for LHD:
|
Remove in this Direction |
Slide in the direction indicated by the arrow shown in the illustration to detach the claw.
w/ Solar Sensor, w/ Automatic Light Control System:
Detach the clamp and remove the No. 4 instrument panel wire.
w/ Solar Sensor, w/o Automatic Light Control System:
Detach the clamp and remove the No. 4 instrument panel wire.
w/ Ion Generator:
Detach the clamp and remove the No. 4 instrument panel wire.
w/ Ion Generator, Blind Spot Monitor System:
Detach the clamp and remove the No. 4 instrument panel wire.
for RHD:
|
Remove in this Direction |
Slide in the direction indicated by the arrow shown in the illustration to detach the claw.
w /Solar Sensor, w/ Automatic Light Control System:
Detach the clamp and remove the No. 4 instrument panel wire.
w /Solar Sensor, w/o Automatic Light Control System:
Detach the clamp and remove the No. 4 instrument panel wire.
w/ Blind Spot Monitor System:
Detach the clamp and remove the No. 4 instrument panel wire.
w/ Blind Spot Monitor System, w/ Automatic Light Control System:
Detach the clamp and remove the No. 4 instrument panel wire.
w/ Ion Generator:
Detach the clamp and remove the No. 4 instrument panel wire.
w/ Ion Generator, Blind Spot Monitor System:
Detach the clamp and remove the No. 4 instrument panel wire.
73960A
15.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/ Front Passenger Airbag)
73908
16.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG CASE SUB-ASSEMBLY (w/o Front Passenger Airbag)
|
Screw <A> |
Remove the 2 screws <A>.
Lean the instrument panel safety pad sub-assembly and detach the hook.
Detach the hook to remove the instrument panel passenger airbag case sub-assembly.
82142A
17.REMOVE NO. 2 INSTRUMENT PANEL WIRE
for LHD:
Disconnect the connector.
Remove the screw.
Detach the clamp and remove the No. 2 instrument panel wire.
| *A | w/o Front Passenger Airbag | *B | w/ Front Passenger Airbag |
for RHD:
Disconnect the connector.
Remove the screw.
Detach the clamp and remove the No. 2 instrument panel wire.
| *A | w/o Front Passenger Airbag | *B | w/ Front Passenger Airbag |
55620
18.REMOVE INSTRUMENT PANEL CUP HOLDER ASSEMBLY
|
Screw <A> |
Remove the 5 screws <A>.
Detach the claw and guide and remove the instrument panel cup holder assembly.
55972C
19.REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT
|
Clip <H> |
Remove the clip <H> and No. 2 side defroster nozzle duct.
55316A
20.REMOVE UPPER INSTRUMENT SIDE PATCH LH
|
Clip <H> |
Remove the clip <H>.
|
Screw <A> |
Remove the screw <A>.
|
Remove in this Direction |
Detach the guide and remove the upper instrument side patch LH as shown in the illustration.
55660
21.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
|
Screw <A> |
Remove the 3 screws <A>.
Detach the guide and remove the No. 2 instrument panel register assembly.
55662A
22.REMOVE NO. 2 INSTRUMENT PANEL REGISTER BEZEL (for Wagon)
Detach the claw and guide and remove the No. 2 instrument panel register bezel.
55971C
23.REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT
|
Clip <H> |
Remove the clip <H> and No. 1 side defroster nozzle duct.
55315C
24.REMOVE UPPER INSTRUMENT SIDE PATCH RH
|
Clip <H> |
Remove the clip <H>.
|
Screw <A> |
Remove the screw <A>.
|
Remove in this Direction |
Detach the guide and remove the upper instrument side patch RH as shown in the illustration.
55650
25.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
|
Screw <A> |
Remove the 3 screws <A>.
Detach the guide and remove the No. 1 instrument panel register assembly.
55661A
26.REMOVE INSTRUMENT PANEL REGISTER BEZEL (for Wagon)
Detach the claw and guide and remove the instrument panel register bezel.
55355
27.REMOVE NO. 1 INSTRUMENT PANEL CUSHION (for Full-trim)
Remove the No. 1 instrument panel cushion.
55356C
28.REMOVE NO. 2 INSTRUMENT PANEL CUSHION (for Full-trim, except Wagon)
Remove the No. 2 instrument panel cushion.
55357B
29.REMOVE NO. 3 INSTRUMENT PANEL CUSHION (for Full-trim)
Remove the No. 3 instrument panel cushion.
55471C
30.REMOVE INSTRUMENT PANEL NAME PLATE (w/o Front Passenger Airbag)
|
Screw <A> |
Remove the 2 screws <A>.
| *a | No. 4 Instrument Panel Safety Pad Retainer |
Remove the No. 4 instrument panel safety pad retainer and instrument panel name plate.
55962D
31.REMOVE NO. 2 SIDE DEFROSTER NOZZLE
Detach the claw and guide and remove the No. 2 side defroster nozzle.
55961B
32.REMOVE NO. 1 SIDE DEFROSTER NOZZLE
Use the same procedure for the No. 2 side defroster nozzle.
55403
33.REMOVE METER HOOD SUB-ASSEMBLY (for Wagon)
|
Remove in this Direction |
Detach the claw and remove the meter hood sub-assembly.
55047A
34.REMOVE METER HOOD CLUSTER SUB-ASSEMBLY RH (for Wagon)
Detach the claw and remove the meter hood cluster sub-assembly RH.
55048A
35.REMOVE METER HOOD CLUSTER SUB-ASSEMBLY LH (for Wagon)
Detach the claw in the order shown in the illustration and remove the meter hood cluster sub-assembly LH.
55328
36.REMOVE NO. 1 INSTRUMENT PANEL PIN
Use the same procedure for the opposite side.
|
Screw <A> |
Remove the screw <A>.
Detach the guide and remove the No. 1 instrument panel pin.
55349A
37.REMOVE INSTRUMENT PANEL CUSHION
Remove the instrument panel cushion.
55981
38.REMOVE NO. 1 DEFROSTER NOZZLE GARNISH (for Wagon)
|
Screw <A> |
Remove the 2 screws <A>.
|
Remove in this Direction |
Detach the claw and remove the No. 1 defroster nozzle garnish.
55532B
39.REMOVE CIGAR LIGHTER HOLE COVER (w/o Power Outlet Socket)
|
Remove in this Direction |
Detach the claw and remove the cigar lighter hole cover as shown in the illustration.
86211
40.REMOVE NO. 1 RADIO BRACKET (w/ Radio Receiver Opening Cover)
|
Screw <A> |
Remove the screw <A>.
Detach the claw and remove the No. 1 radio bracket.
86212
41.REMOVE NO. 2 RADIO BRACKET (w/ Radio Receiver Opening Cover)
|
Screw <A> |
Remove the screw <A>.
Detach the claw and remove the No. 2 radio bracket.
55473A
42.REMOVE INSTRUMENT PANEL FINISH PANEL RETAINER (for Full-trim, except Wagon)
Remove the 6 screws and instrument panel finish panel retainer.
55618B
43.REMOVE NO. 3 SWITCH HOLE BASE (for Full-trim, except Wagon)
Remove the 3 screws and No. 3 switch hole base.
55539
44.REMOVE SPARE SWITCH HOLE COVER (for Semi-trim)
|
Screw <A> |
Remove the 3 screws <A> and spare switch hole cover.
55308D
45.REMOVE CENTER INSTRUMENT PANEL BOX SUB-ASSEMBLY (for Full-trim)
except Wagon:
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front)>REMOVAL
for Wagon:
Remove the 4 screws.
Detach the claw and guide and remove the center instrument panel box sub-assembly.
55414A
46.REMOVE INSTRUMENT CLUSTER FINISH PANEL END (w/ Radio Receiver Opening Cover)
|
Screw <A> |
Remove the 4 screws <A> and instrument cluster finish panel end.
47.REMOVE GLOVE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY
for LHD:
| *a | Stopper |
|
Remove in this Direction |
Push the stopper to release the lock, and then push the glove compartment door lock cylinder assembly and remove it from the glove compartment door assembly.
for RHD:
| *a | Stopper |
|
Remove in this Direction |
Push the stopper to release the lock, and then push the glove compartment door lock cylinder assembly and remove it from the glove compartment door assembly.
55550
48.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
Remove the 2 screws and glove compartment door assembly.
55557A
49.REMOVE GLOVE COMPARTMENT DOOR CHECK CUSHION
|
Remove in this Direction |
Detach the claw and remove the glove compartment door check cushion.
Use the same procedure to remove the glove compartment door check cushion on the other side.
81260
50.REMOVE GLOVE BOX LIGHT ASSEMBLY (for Wagon)
55524H
51.REMOVE SWITCH BASE HOLE COVER (for RHD, Separate Seat Type)
|
Remove in this Direction |
Detach the clip and remove the switch base hole cover.
55548A
52.REMOVE INSTRUMENT PANEL HOLE COVER (for RHD, Separate Seat Type)
Remove the 2 screws.
|
Remove in this Direction |
Detach the guide and remove the instrument panel hole cover.