Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
55548A
1.INSTALL INSTRUMENT PANEL HOLE COVER (for RHD, Separate Seat Type)
|
Install in this Direction |
Attach the guide to set the instrument panel hole cover.
Install the instrument panel hole cover with the 2 screws.
55524H
2.INSTALL SWITCH BASE HOLE COVER (for RHD, Separate Seat Type)
|
Install in this Direction |
Attach the clip to install the switch base hole cover.
81260
3.INSTALL GLOVE BOX LIGHT ASSEMBLY (for Wagon)
55557A
4.INSTALL GLOVE COMPARTMENT DOOR CHECK CUSHION
|
Install in this Direction |
Attach the claw to install the glove compartment door check cushion.
Use the same procedure to install the glove compartment door check cushion on the other side.
55550
5.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
Install the glove compartment door assembly with the 2 screws.
6.INSTALL GLOVE COMPARTMENT DOOR LOCK CYLINDER ASSEMBLY
for LHD:
| *a | Stopper |
|
Install in this Direction |
Push the stopper and insert the glove compartment door lock cylinder assembly to the glove compartment door assembly to install it.
for RHD:
| *a | Stopper |
|
Install in this Direction |
Push the stopper and insert the glove compartment door lock cylinder assembly to the glove compartment door assembly to install it.
55414A
7.INSTALL INSTRUMENT CLUSTER FINISH PANEL END (w/ Radio Receiver Opening Cover)
|
Screw <A> |
Install the instrument cluster finish panel end with the 4 screws <A>.
55308D
8.INSTALL CENTER INSTRUMENT PANEL BOX SUB-ASSEMBLY (for Full-trim)
except Wagon:
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL (for Front)>INSTALLATION
for Wagon:
Attach the claw and guide to install the center instrument panel box sub-assembly.
Install the 4 screws.
55539
9.INSTALL SPARE SWITCH HOLE COVER (for Semi-trim)
|
Screw <A> |
Install the spare switch hole cover with the 3 screws <A>.
55618B
10.INSTALL NO. 3 SWITCH HOLE BASE (for Full-trim, except Wagon)
Install the No. 3 switch hole base with the 3 screws.
55473A
11.INSTALL INSTRUMENT PANEL FINISH PANEL RETAINER (for Full-trim, except Wagon)
Install the instrument panel finish panel retainer with the 6 screws.
86212
12.INSTALL NO. 2 RADIO BRACKET (w/ Radio Receiver Opening Cover)
|
Screw <A> |
Attach the claw to install the No. 2 radio bracket with the screw <A>.
86211
13.INSTALL NO. 1 RADIO BRACKET (w/ Radio Receiver Opening Cover)
|
Screw <A> |
Attach the claw to install the No. 1 radio bracket with the screw <A>.
55532B
14.INSTALL CIGAR LIGHTER HOLE COVER (w/o Power Outlet Socket)
|
Install in this Direction |
Attach the claw to install the cigar lighter hole cover as shown in the illustration.
55981
15.INSTALL NO. 1 DEFROSTER NOZZLE GARNISH (for Wagon)
|
Install in this Direction |
Attach the claw to install the No. 1 defroster nozzle garnish as shown in the illustration.
|
Screw <A> |
Install the 2 screws <A>.
55349A
16.INSTALL INSTRUMENT PANEL CUSHION
Install the instrument panel cushion as shown in the illustration.
55328
17.INSTALL NO. 1 INSTRUMENT PANEL PIN
Use the same procedure for the opposite side.
Attach the guide to set the No. 1 instrument panel pin.
|
Screw <A> |
Install the No. 1 instrument panel pin with the screw <A>.
55048A
18.INSTALL METER HOOD CLUSTER SUB-ASSEMBLY LH (for Wagon)
Attach the claw to install the meter hood cluster sub-assembly LH.
55047A
19.INSTALL METER HOOD CLUSTER SUB-ASSEMBLY RH (for Wagon)
Attach the claw to install the meter hood cluster sub-assembly RH.
55403
20.INSTALL METER HOOD SUB-ASSEMBLY (for Wagon)
|
Install in this Direction |
Attach the claw to install the meter hood sub-assembly as shown in the illustration.
55962D
21.INSTALL NO. 2 SIDE DEFROSTER NOZZLE
Attach the guide and claw to install the No. 2 side defroster nozzle.
55961B
22.INSTALL NO. 1 SIDE DEFROSTER NOZZLE
Use the same procedure for the No. 2 side defroster nozzle.
55471C
23.INSTALL INSTRUMENT PANEL NAME PLATE (w/o Front Passenger Airbag)
| *a | No. 4 Instrument Panel Safety Pad Retainer |
Install the No. 4 instrument panel safety pad retainer and instrument panel name plate.
|
Screw <A> |
Install the 2 screws <A>.
55357B
24.INSTALL NO. 3 INSTRUMENT PANEL CUSHION (for Full-trim)
Installing the part with double-sided tape residue still remaining can cause poor adhesion. Therefore, using a cloth or other material, clean the part until the residue is completely removed (when reusing the instrument panel sub-assembly).
Remove the release paper from new No. 3 instrument panel cushion.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | Marking |
Align the No. 3 instrument panel cushion with the markings on the instrument panel sub-assembly and install them as shown in the illustration.
55356C
25.INSTALL NO. 2 INSTRUMENT PANEL CUSHION (for Full-trim, except Wagon)
Install the No. 2 instrument panel cushion as shown in the illustration.
55355
26.INSTALL NO. 1 INSTRUMENT PANEL CUSHION (for Full-trim)
Install the No. 1 instrument panel cushion as shown in the illustration.
55661A
27.INSTALL INSTRUMENT PANEL REGISTER BEZEL (for Wagon)
Attach the guide and claw to install the instrument panel register bezel.
55650
28.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Attach the guide to set the No. 1 instrument panel register assembly.
|
Screw <A> |
Install the No. 1 instrument panel register assembly with the 3 screws <A>.
55315C
29.INSTALL UPPER INSTRUMENT SIDE PATCH RH
|
Install in this Direction |
Attach the guide to set the upper instrument side patch RH as shown in the illustration.
|
Screw <A> |
Install the upper instrument side patch RH with the screw <A>.
|
Clip <H> |
Install the clip <H>.
55971C
30.INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT
|
Clip <H> |
Install the No. 1 side defroster nozzle duct with the clip <H>.
55662A
31.INSTALL NO. 2 INSTRUMENT PANEL REGISTER BEZEL (for Wagon)
Attach the guide and claw to install the No. 2 instrument panel register bezel.
55660
32.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Attach the guide to set the No. 2 instrument panel register assembly.
|
Screw <A> |
Install the No. 2 instrument panel register assembly with the 3 screws <A>.
55316A
33.INSTALL UPPER INSTRUMENT SIDE PATCH LH
|
Install in this Direction |
Attach the guide to set the upper instrument side patch LH as shown in the illustration.
|
Screw <A> |
Install the upper instrument side patch LH with the screw <A>.
|
Clip <H> |
Install the clip <H>.
55972C
34.INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT
|
Clip <H> |
Install the No. 2 side defroster nozzle duct with the clip <H>.
55620
35.INSTALL INSTRUMENT PANEL CUP HOLDER ASSEMBLY
Attach the guide and claw to install the instrument panel cup holder assembly.
|
Screw <A> |
Install the 5 screws <A>.
82142A
36.INSTALL NO. 2 INSTRUMENT PANEL WIRE
for LHD:
Attach the clamp to install the No. 2 instrument panel wire with the screw.
| *A | w/o Front Passenger Airbag | *B | w/ Front Passenger Airbag |
Connect the connector.
for RHD:
Attach the clamp to install the No. 2 instrument panel wire with the screw.
| *A | w/o Front Passenger Airbag | *B | w/ Front Passenger Airbag |
Connect the connector.
73908
37.INSTALL INSTRUMENT PANEL PASSENGER AIRBAG CASE SUB-ASSEMBLY (w/o Front Passenger Airbag)
Attach the hook.
Push in the instrument panel passenger airbag case sub-assembly to attach the hook.
|
Screw <A> |
Install the instrument panel passenger airbag case sub-assembly with the 2 screws <A>.
73960A
38.INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/ Front Passenger Airbag)
82144
39.INSTALL NO. 4 INSTRUMENT PANEL WIRE
for LHD:
w/ Solar Sensor, w/ Automatic Light Control System:
Attach the clamp to install the No. 4 instrument panel wire.
w/ Solar Sensor, w/o Automatic Light Control System:
Attach the clamp to install the No. 4 instrument panel wire.
w/ Ion Generator:
Attach the clamp to install the No. 4 instrument panel wire.
w/ Ion Generator, Blind Spot Monitor System:
Attach the clamp to install the No. 4 instrument panel wire.
|
Install in this Direction |
Install in the direction indicated by the arrow shown in the illustration to attach the claw.
for RHD:
w/ Solar Sensor, w/ Automatic Light Control System:
Attach the clamp to install the No. 4 instrument panel wire.
w/ Solar Sensor, w/o Automatic Light Control System:
Attach the clamp to install the No. 4 instrument panel wire.
w/ Blind Spot Monitor System:
Attach the clamp to install the No. 4 instrument panel wire.
w/ Automatic Light Control System, Blind Spot Monitor System:
Attach the clamp to install the No. 4 instrument panel wire.
w/ Ion Generator:
Attach the clamp to install the No. 4 instrument panel wire.
w/ Ion Generator, Blind Spot Monitor System:
Attach the clamp to install the No. 4 instrument panel wire.
|
Install in this Direction |
Install in the direction indicated by the arrow shown in the illustration to attach the claw.
86681C
40.INSTALL ANTENNA DIVIDER (for Wagon, w/ Telematics Transceiver)
89747F
41.INSTALL BLIND SPOT MONITOR BUZZER (w/ Blind Spot Monitor System)
89120A
42.INSTALL AUTOMATIC LIGHT CONTROL SENSOR (w/ Automatic Light Control System)
88625H
43.INSTALL COOLER (SOLAR SENSOR) THERMISTOR (w/o Automatic Light Control System)
55538C
44.INSTALL COOLER SWITCH HOLE COVER (w/ Cover)
|
Install in this Direction |
Attach the claw to install the cooler switch hole cover.
86101
45.INSTALL ANTENNA CORD SUB-ASSEMBLY
46.INSTALL NAVIGATION ANTENNA ASSEMBLY WITH BRACKET (w/ Navigation System)
55844
47.INSTALL NO. 2 HEATER TO REGISTER DUCT
|
Screw <A> |
Attach the guide to install the No. 2 heater to register duct with the 4 screws <A>.
55845A
48.INSTALL NO. 3 HEATER TO REGISTER DUCT
|
Screw <A> |
Attach the guide to install the No. 3 heater to register duct with the 3 screws <A>.
55843A
49.INSTALL NO. 1 HEATER TO REGISTER DUCT
|
Screw <A> |
Attach the guide to install the No. 1 heater to register duct with the 3 screws <A>.
87201N
50.INSTALL AIR DUCT SUB-ASSEMBLY (for Wagon, w/ Ion Generator)
Install the air duct sub-assembly.
88051B
51.INSTALL NO. 1 ION GENERATOR SUB-ASSEMBLY (for Wagon, w/ Ion Generator)
55990C
52.INSTALL CENTER DEFROSTER NOZZLE ASSEMBLY
Attach the guide to set the center defroster nozzle assembly.
|
Screw <A> |
Install the center defroster nozzle assembly with the 5 screws <A>.