The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 1 indoor electrical key antenna assembly removal/installation are shown below.
Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
The procedure listed below is a representative example.
1. PRECAUTION (for First Row)
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type C:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
If the pretensioner has been deployed, replace any damaged parts as necessary.
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for First Row)
Operate the rear power seat switch and move the ottoman to the uppermost position and seatback to the frontmost position.
Disconnet the cable from the negative (-) battery terminal.
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
3.REMOVE REAR NO. 1 SEAT ASSEMBLY LH
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
4.REMOVE REAR NO. 1 SEAT ASSEMBLY RH
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
5.REMOVE REAR NO. 2 SEAT ASSEMBLY LH
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
6.REMOVE REAR NO. 2 SEAT ASSEMBLY RH
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
7.REMOVE REAR NO. 3 SEAT ASSEMBLY LH
for Folding Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>REMOVAL
for 60/40 Split Seat Type 40 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>REMOVAL
8.REMOVE REAR NO. 3 SEAT ASSEMBLY RH
for Folding Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>REMOVAL
for 60/40 Split Seat Type 60 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)>REMOVAL
58595
9.REMOVE NO. 3 FLOOR CARPET MOULDING NO. 1
Click hereVehicle Interior>SEAT>SEAT RAIL>REMOVAL
58595
10.REMOVE NO. 3 FLOOR CARPET MOULDING NO. 2
Click hereVehicle Interior>SEAT>SEAT RAIL>REMOVAL
58595
11.REMOVE NO. 3 FLOOR CARPET MOULDING NO. 3 (w/ Power Supply Unit)
Click hereVehicle Interior>SEAT>SEAT RAIL>REMOVAL
58595
12.REMOVE NO. 3 FLOOR CARPET MOULDING NO. 4 (w/ Power Supply Unit)
Click hereVehicle Interior>SEAT>SEAT RAIL>REMOVAL
13.REMOVE SEAT TRACK RAIL PROTECTOR
Click hereVehicle Interior>SEAT>SEAT RAIL>REMOVAL
58570C
14.REMOVE REAR FLOOR CARPET ASSEMBLY
Click hereVehicle Interior>SEAT>SEAT RAIL>REMOVAL
58513F
15.REMOVE NO. 3 FLOOR MAT
Remove the No. 3 floor mat.
58514H
16.REMOVE NO. 4 FLOOR MAT
Remove the No. 4 floor mat.
899A0
17.REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY
Do not reuse parts if dropped or subjected to any strong impact.
for LH Side:
| *a | Protective Tape |
Using a thin-bladed screwdriver, detach the claw and remove the No. 1 indoor electrical key antenna assembly.
Tape the thin-bladed screwdriver tip before use.
Disconnect the connector.
for RH Side:
| *a | Protective Tape |
Using a thin-bladed screwdriver, detach the claw and remove the No. 1 indoor electrical key antenna assembly.
Tape the thin-bladed screwdriver tip before use.
Disconnect the connector.