Use the same procedure for RHD and LHD vehicles.
The procedure below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure below is for the LH side.
67858J
1.INSTALL SLIDE DOOR RAIL PROTECTOR LH
When installing the slide door rail protector LH, heat the center slide door rail sub-assembly LH and slide door rail protector LH using a heat light.
| Item | Temperature |
|---|---|
| Center Slide Door Rail Sub-assembly | 40 to 60°C (104 to 140°F) |
| Slide Door Rail Protector LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the center slide door rail sub-assembly LH and slide door rail protector LH excessively.
Clean the center slide door rail sub-assembly LH surface.
Using a heat light, heat the center slide door rail sub-assembly LH surface.
Remove any remaining double-sided tape from the slide door rail protector LH.
Wipe off any tape adhesive residue with cleaner.
Install a new slide door rail protector LH.
Using a heat light, heat the center slide door rail sub-assembly LH and slide door rail protector LH.
Remove the release paper from the slide door rail protector LH.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *1 | Slide door rail protector LH |
| *a | Cutout |
| *b | R End |
|
Double-sided Tape |
Align the cutout of the front end of the slide door rail protector LH with the center slide door rail sub-assembly LH, align the end of the curve, set the slide door rail protector LH into place and install the slide door rail protector LH as shown in the illustration.
Firmly press the slide door rail protector LH to attach it.
68304B
2.INSTALL CENTER SLIDE DOOR RAIL SUB-ASSEMBLY LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Insert the stud bolt at the front end of the center slide door rail LH in the direction (1) indicated by the arrow shown in the illustration.
Insert the stud bolt at the rear end of the center slide door rail LH in the direction (2) indicated by the arrow shown in the illustration and install the center slide door rail LH.
Do not damage the vehicle body with the slide door rail.
Using a T40 "TORX" socket wrench, install the "TORX" screw.
Install the 5 nuts.
68390A
3.INSTALL CENTER SLIDE DOOR HINGE ASSEMBLY LH
|
Install in this Direction |
Move the slide door to a position where the center slide door hinge assembly LH can be installed.
Make sure not to contact the vehicle body with the slide door.
|
Install in this Direction |
Insert the slide door hinge into the slide door rail.
Make sure not to contact the vehicle body with the slide door.
Do not damage the vehicle body with the center slide door hinge assembly LH.
Install the center slide door hinge assembly LH with the 2 bolts.
68074
4.INSTALL SLIDE RAIL END MOULDING SUB-ASSEMBLY LH
Use the same procedure described for the LH side.
Click hereVehicle Exterior>DOOR / HATCH>SLIDE DOOR (for Wagon)>REASSEMBLY
62640M
5.INSTALL REAR QUARTER TRIM BOARD ASSEMBLY LH
62630L
6.INSTALL REAR QUARTER TRIM BOARD ASSEMBLY RH (w/ Rear Air Conditioning System)
67872A
7.INSTALL NO. 1 SLIDE DOOR WEATHERSTRIP LH
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>INSTALLATION
67918D
8.INSTALL REAR DOOR SCUFF PLATE LH
73370E
9.INSTALL REAR SEAT OUTER BELT ASSEMBLY LH (w/ Seat Belt)
73178C
10.INSTALL SEAT BELT ANCHOR COVER CAP (w/ Seat Belt)
67935
11.INSTALL BACK DOOR SCUFF PLATE
12.INSTALL REAR SEAT ASSEMBLY LH
for Folding Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>INSTALLATION
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>INSTALLATION
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>INSTALLATION
for 60/40 Split Seat Type 40 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>INSTALLATION
for 60/40 Split Seat Type 60 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)>INSTALLATION
13.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Rear Curtain Shield Airbag)
for 7GR-FKS:
for 1GD-FTV:
14. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (w/ Rear Curtain Shield Airbag)
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
15. CHECK SRS WARNING LIGHT (w/ Rear Curtain Shield Airbag)
16. PERFORM DIAGNOSTIC SYSTEM CHECK (w/ Rear Curtain Shield Airbag)