Wear protective gloves. Sharp areas on the parts may injure your hands.
There is risk of injury.
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 3 seat outer belt assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
1. PRECAUTION (for First Row)
Be sure to read Precaution thoroughly before servicing.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type C:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
If the pretensioner has been deployed, replace any damaged parts as necessary.
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for First Row)
Operate the rear power seat switch and move the ottoman to the uppermost position and seatback to the frontmost position.
Disconnet the cable from the negative (-) battery terminal.
for 7GR-FKS:
for 1GD-FTV:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
3.REMOVE REAR SEAT ASSEMBLY
for Folding Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Folding Type)>REMOVAL
for 60/40 Split Seat Type 40 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 40 Side)>REMOVAL
for 60/40 Split Seat Type 60 Side:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type 60 Side)>REMOVAL
for Manual Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Manual Captain Seat)>REMOVAL
for Power Captain Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Power Captain Seat)>REMOVAL
67935
4.REMOVE BACK DOOR SCUFF PLATE
73233
5.REMOVE OUTER LAP BELT ANCHOR COVER
| *a | Guide A |
| *b | Guide B |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull in the removal direction (1) shown in the illustration and detach the guide A.
Detach the guide B in the removal direction (2) shown in the illustration and remove the outer lap belt anchor cover.
73570A
6.REMOVE NO. 3 SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
Remove the bolt and floor anchor of the No. 3 seat outer belt assembly LH.
67872A
7.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP LH
Use the same procedure described for the RH side.
Pull back the No. 1 slide door weatherstrip LH so that the rear quarter trim panel assembly LH can be removed.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (for Wagon)>REMOVAL
62520B
8.REMOVE QUARTER TRIM PANEL ASSEMBLY LH
73570A
9.REMOVE NO. 3 SEAT OUTER BELT ASSEMBLY LH
|
Open in this Direction |
Using moulding remover D, detach the claw and open the cover as shown in the illustration.
Remove the bolt.
Remove the 2 bolts.
Detach the guide and remove the No. 3 seat outer belt assembly LH.
73015A
10.REMOVE OUTER BELT ANCHOR BRACKET SUB-ASSEMBLY RH (for 60/40 Split Seat Type RH Side)
Perform this procedure when replacing the outer belt anchor bracket sub-assembly RH.
Remove the bolt and outer belt anchor bracket sub-assembly RH.