The seat belt warning light on the combination meter assembly illuminates, blinks or turns off in accordance with the state of the front seat inner belt assembly (for Driver Side).
except Wagon:
for Wagon:
The seat belt warning system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
The seat belt warning light on the combination meter assembly is used for the driver seat, front passenger seat and front center seat (w/ Front Center Seat Belt Warning). Check that the operation of the seat belt warning light is normal first.
Click here
If the seat belt warning light does not operate for the driver seat, front passenger seat and front center seat (w/ Front Center Seat Belt Warning), replace the combination meter assembly.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.*
*: w/ Entry and Start System
Read the Data List according to the display on the GTS.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Seat Buckle SW | Driver seat belt buckle switch signal | OFF or ON | OFF: Driver seat belt unfastened
ON: Driver seat belt fastened |
- |
| Tester Display |
|---|
| D Seat Buckle SW |
ON or OFF appears on the GTS screen according to the driver seat belt condition.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (except Wagon) | B |
| NG (for Wagon) | C |
A
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
B
C
Remove the front seat inner belt assembly (for Driver Side).
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Separate Seat Type)>REMOVAL
Inspect the front seat inner belt assembly (for Driver Side).
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Separate Seat Type)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Separate Seat Type)>REMOVAL
Disconnect the n1*1, m1*2, N24*3 or N26*4 front seat inner belt assembly (for Driver Side) connector.
*1: for LHD with Seat Airbag
*2: for RHD with Seat Airbag
*3: for LHD without Seat Airbag
*4: for RHD without Seat Airbag
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| n1-4 - 3D-33 | Always | Below 1 Ω |
| n1-4 or 3D-33 - Body ground | Always | 10 kΩ or higher |
| n1-3 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| m1-4 - 3D-33 | Always | Below 1 Ω |
| m1-4 or 3D-33 - Body ground | Always | 10 kΩ or higher |
| m1-3 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N24-6 - 3D-33 | Always | Below 1 Ω |
| N24-6 or 3D-33 - Body ground | Always | 10 kΩ or higher |
| N24-4 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N26-6 - 3D-33 | Always | Below 1 Ω |
| N26-6 or 3D-33 - Body ground | Always | 10 kΩ or higher |
| N26-4 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-18 (DBKL) - 3D-33 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Remove the front seat inner belt assembly (for Driver Side).
for Separate Seat Type:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Separate Seat Type)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL
Inspect the front seat inner belt assembly (for Driver Side).
for Separate Seat Type:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Separate Seat Type)>INSPECTION
for Power Seat:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Separate Seat Type:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Separate Seat Type)>REMOVAL
for Power Seat:
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)>REMOVAL
Disconnect the n1*1, m1*2, N181*3 or N183*4 front seat inner belt assembly (for Driver Side) connector.
*1: for LHD with Seat Airbag
*2: for RHD with Seat Airbag
*3: for LHD without Seat Airbag
*4: for RHD without Seat Airbag
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| n1-4 - 3D-33 | Always | Below 1 Ω |
| n1-4 or 3D-33 - Body ground | Always | 10 kΩ or higher |
| n1-3 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| m1-4 - 3D-33 | Always | Below 1 Ω |
| m1-4 or 3D-33 - Body ground | Always | 10 kΩ or higher |
| m1-3 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N181-14 - 3D-33 | Always | Below 1 Ω |
| N181-14 or 3D-33 - Body ground | Always | 10 kΩ or higher |
| N181-15 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N183-14 - 3D-33 | Always | Below 1 Ω |
| N183-14 or 3D-33 - Body ground | Always | 10 kΩ or higher |
| N183-15 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-18 (DBKL) - 3D-33 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
for LHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD:
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL