The combination meter assembly and engine oil level sensor are connected via direct line. The combination meter assembly determines the engine oil level based on the engine oil level sensor signal.
As the engine oil level may be unstable when the engine is cold or running at high speeds, the combination meter assembly receives the engine coolant temperature signal and engine speed signal from the ECM via CAN communication in order to prevent the oil level warnings from being output erroneously.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
The following troubleshooting procedure is based on the assumption that the SFI system is normal. Confirm that the SFI system is not malfunctioning before performing the following procedure.
Click hereEngine / Hybrid System>7GR-FKS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
The following troubleshooting procedure is based on the assumption that the ECD system is normal. Confirm that the ECD system is not malfunctioning before performing the following procedure.
w/ DPF: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>HOW TO PROCEED WITH TROUBLESHOOTING
w/ Urea SCR System: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING
w/ EGR Cooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>HOW TO PROCEED WITH TROUBLESHOOTING
w/o EGR Cooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>HOW TO PROCEED WITH TROUBLESHOOTING
w/ Exhaust Gas Temperature Sensor for EGR: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Exhaust Gas Temperature Sensor for EGR)>HOW TO PROCEED WITH TROUBLESHOOTING
Remove the engine oil level sensor.
for 7GR-FKS:
Click hereEngine / Hybrid System>7GR-FKS (LUBRICATION)>OIL LEVEL SENSOR>REMOVAL
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL LEVEL SENSOR>REMOVAL
Inspect the engine oil level sensor.
for 7GR-FKS:
Click hereEngine / Hybrid System>7GR-FKS (LUBRICATION)>OIL LEVEL SENSOR>INSPECTION
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL LEVEL SENSOR>INSPECTION
| Proceed to |
|---|
| OK (for 7GR-FKS) |
| OK (for 1GD-FTV) |
| NG |
OK (for 7GR-FKS)
OK (for 1GD-FTV)
NG
for 7GR-FKS:
Click hereEngine / Hybrid System>7GR-FKS (LUBRICATION)>OIL LEVEL SENSOR>REMOVAL
for 1GD-FTV:
Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL LEVEL SENSOR>REMOVAL
Disconnect the E96 engine oil level sensor connector.
Disconnect the N23 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N23-31 (OILW) - E96-1 (LOIL) | Always | Below 1 Ω |
| N23-31 (OILW) or E96-1 (LOIL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the E97 engine oil level sensor connector.
Disconnect the N23 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N23-31 (OILW) - E97-1 | Always | Below 1 Ω |
| E97-2 - Body ground | Always | Below 1 Ω |
| N23-31 (OILW) or E97-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG