Home › Engine / Hybrid System › 1GD-FTV (STARTING) › GLOW PLUG › from 2019.06
RM35X0E _51 Engine / Hybrid System _078666 1GD-FTV STARTING _0382049 GLOW PLUG A

1GD-FTV STARTING  GLOW PLUG  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the glow plug assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative when not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative when not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



CAUTION / NOTICE / HINT

CAUTION:
·
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·

Make sure to wear protective gloves when performing work to avoid burns.



NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Common rail assembly
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The common rail assembly is a precision instrument. Do not use the common rail assembly if it is struck or dropped.

·

Hold the common rail assembly itself during removal and installation. Do not hold the pressure discharge valve or fuel pressure sensor, etc.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 1. WARM UP ENGINE

CAUTION:

To protect the glow plug assembly from damage, before removing the glow plug assembly, make sure to warm up the engine.


Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 23810A 4.REMOVE COMMON RAIL ASSEMBLY

Hide 19871 5.REMOVE NO. 1 GLOW PLUG CONNECTOR

CAUTION:

Make sure to wear protective gloves when performing work to avoid burns.


a.
A346967

Using an E8 "TORX" socket wrench, remove the stud bolt from the intake manifold.


b.
A346968

Remove the 4 glow plug screw grommets.


c.
A346969

Remove the 4 nuts and No. 1 glow plug connector.


Hide 19850 6.REMOVE GLOW PLUG ASSEMBLY

CAUTION:

Make sure to wear protective gloves when performing work to avoid burns.


a.
A346970

Using a 10 mm deep socket wrench, remove the 4 glow plug assemblies.