Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
67935
1.INSTALL BACK DOOR SCUFF PLATE
|
Install in this Direction |
Attach the clip to install the back door scuff plate as shown in the illustration.
Install the 4 screws.
2.INSTALL ROOF HEADLINING ASSEMBLY (for Standard Roof)
Tilt the roof headlining assembly vertically and carry it onto the vehicle through the back door.
Installation of the roof headlining assembly must be performed by multiple people to prevent deformation of the roof headlining assembly.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
Attach the claw to install the visor holder base.
Use the same procedure for the opposite side.
w/o Rear Air Duct, for 4 Door:
Attach the fastener.
Install the roof headlining assembly with the 12 clips and 2 plates.
When installing the clips indicated by the white arrow, make sure to install the plate between the roof headlining assembly.
| *a | Fastener | *b | Plate |
|
w/ Plate | - | - |
w/o Rear Air Duct, for 5 Door:
Attach the fastener.
Install the roof headlining assembly with the 11 clips and 2 plates.
When installing the clips indicated by the white arrow, make sure to install the plate between the roof headlining assembly.
| *a | Fastener | *b | Plate |
|
w/ Plate | - | - |
w/ Rear Air Duct:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>INSTALLATION
for Rear Roof RH Side, w/ Digital Inner Mirror:
Attach the clamp and connect the connector.
for Rear Roof LH Side:
| *A | w/ Rear Wiper or w/ Digital Inner Mirror |
|
Connector |
|
Washer Hose |
Connect the connector.
w/ Rear Wiper or w/ Digital Inner Mirror:
Connect the washer hose.
for Front Pillar LH Side:
w/ Curtain Shield Airbag:
Remove the protective cover installed to the front pillar LH.
| *A | w/ Rear Wiper or w/ Digital Inner Mirror |
|
Connector |
|
Washer Hose |
w/ Rear Wiper or w/ Digital Inner Mirror:
Connect the washer hose.
Attach the wire harness clamp.
Connect the 3 connectors.
w/ Curtain Shield Airbag:
Install the protective cover to the front pillar LH.
for Windshield Glass Side:
Connect each connector.
3.INSTALL ROOF HEADLINING ASSEMBLY (for High Roof)
Tilt the roof headlining assembly vertically and carry it onto the vehicle through the back door.
Installation of the roof headlining assembly must be performed by multiple people to prevent deformation of the roof headlining assembly.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
w/o Rear Air Duct:
Install the roof headlining assembly with the 16 clips and 2 plates.
When installing the clips indicated by the white arrow, make sure to install the plate between the roof headlining assembly.
| *a | Plate | - | - |
|
w/ Plate | - | - |
w/ Rear Air Duct:
Install the roof headlining assembly with the 14 clips and 2 plates.
When installing the clips indicated by the white arrow, make sure to install the plate between the roof headlining assembly.
| *a | Plate | - | - |
|
w/ Plate | - | - |
Install the 4 bolts.
for Roof Headlining Front Side:
w/o Wire Harness Protector:
Attach the clamp.
w/ Wire Harness Protector:
Attach the clamp.
for Rear Roof RH Side, w/ Digital Inner Mirror:
Attach the clamp and connect the connector.
for Rear Roof LH Side:
w/ Rear Wiper or w/ Digital Inner Mirror:
Attach the clamp and connect the washer hose.
Connect the connector.
for Front Pillar LH Side:
w/ Curtain Shield Airbag:
Remove the protective cover installed to the front pillar LH.
| *A | w/ Rear Wiper or w/ Digital Inner Mirror |
|
Connector |
|
Washer Hose |
w/ Rear Wiper or w/ Digital Inner Mirror:
Connect the washer hose.
Attach the wire harness clamp.
Connect the 3 connectors.
w/ Curtain Shield Airbag:
Install the protective cover to the front pillar LH.
for Windshield Glass Side:
Connect each connector.
65896J
4.INSTALL COVER TOP SET BOLT CAP (for Standard Roof, w/ Rear Air Duct)
63413C
5.INSTALL FRONT INNER ROOF RACK BOARD (for High Roof)
63439D
6.INSTALL NO. 2 INNER ROOF RACK COVER (for High Roof)
63438F
7.INSTALL NO. 1 INNER ROOF RACK COVER (for High Roof)
53989A
8.INSTALL AIR INTAKE NET (w/ Rear Air Duct)
74348
9.INSTALL VISOR HOLDER
74320
10.INSTALL VISOR ASSEMBLY LH
74310
11.INSTALL VISOR ASSEMBLY RH
Use the same procedure described for the LH side.
12.INSTALL ASSIST GRIP ASSEMBLY (w/ Assist Grip)
86768
13.INSTALL ROOF ANTENNA COVER (w/ Digital Audio Broadcasting Antenna)
86466D
14.INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)
81260A
15.INSTALL MAP LIGHT ASSEMBLY
87834
16.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER
w/ EC Mirror:
Click hereVehicle Interior>MIRROR (INT)>INNER REAR VIEW MIRROR (w/ EC Mirror)>INSTALLATION
w/ Digital Inner Mirror:
Click hereVehicle Interior>MIRROR (INT)>DIGITAL INNER MIRROR>INSTALLATION
63320E
17.INSTALL REAR ROOF HEADLINING ASSEMBLY (for Standard Roof)
Tilt the rear roof headlining assembly vertically and carry it onto the vehicle through the back door.
Installation of the rear roof headlining assembly must be performed by multiple people to prevent deformation of the roof headlining assembly.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
| *a | Plate |
|
w/ Plate |
Attach the guide.
Install the rear roof headlining assembly with the 16 clips and 2 plates.
When installing the clips indicated by the white arrow, make sure to install the plate between the rear roof headlining assembly.
18.INSTALL REAR ROOF HEADLINING ASSEMBLY (for High Roof)
Tilt the rear roof headlining assembly vertically and carry it onto the vehicle through the back door.
Installation of the rear roof headlining assembly must be performed by multiple people to prevent deformation of the roof headlining assembly.
Check that the corners of the roof headlining are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining or vehicle interior.
w/ Rear Air Duct:
w/ Roof Window Glass:
Install the rear roof headlining assembly with the 29 clips and 4 plates.
When installing the clips indicated by the white arrow, make sure to install the plate between the rear roof headlining assembly.
| *a | Plate | - | - |
|
w/ Plate | - | - |
w/o Roof Window Glass:
Install the rear roof headlining assembly with the 26 clips and 4 plates.
When installing the clips indicated by the white arrow, make sure to install the plate between the rear roof headlining assembly.
| *a | Plate | - | - |
|
w/ Plate | - | - |
w/o Rear Air Duct:
w/ Roof Window Glass:
Install the rear roof headlining assembly with the 23 clips and 4 plates.
When installing the clips indicated by the white arrow, make sure to install the plate between the rear roof headlining assembly.
| *a | Plate | - | - |
|
w/ Plate | - | - |
w/o Roof Window Glass:
Install the rear roof headlining assembly with the 25 clips and 4 plates.
When installing the clips indicated by the white arrow, make sure to install the plate between the rear roof headlining assembly.
| *a | Plate | - | - |
|
w/ Plate | - | - |
72681E
19.INSTALL REAR SEAT HOOK (for High Roof, w/ Seat Hook)
63349A
20.INSTALL REAR ROOF HEADLINING GARNISH (w/ Roof Window Glass)
w/ Rear Air Duct:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>INSTALLATION
w/o Rear Air Duct:
|
Install in this Direction |
Attach the clip as shown in the illustration to install the rear roof headlining garnish.
81240
21.INSTALL NO. 1 ROOM LIGHT ASSEMBLY
81240D
22.INSTALL NO. 2 ROOM LIGHT ASSEMBLY (for High Roof, w/ No. 2 Room Light Assembly)
Use the same procedure described for the No. 1 room light assembly.
73370E
23.INSTALL REAR SEAT OUTER BELT ASSEMBLY LH (for Van, w/ Seat Belt)
Install the bolt.
|
Close in this Direction |
Attach the claw and close the cover as shown in the illustration.
73360D
24.INSTALL REAR SEAT OUTER BELT ASSEMBLY RH (for Van, w/ Seat Belt)
Use the same procedure described for the LH side.
62411
25.INSTALL CENTER PILLAR GARNISH RH
62412
26.INSTALL CENTER PILLAR GARNISH LH
for 4 Door, Standard Roof:
|
Install in this Direction |
Attach the clip as shown in the illustration to install the center pillar garnish LH.
Install the clip.
for 4 Door, High Roof:
|
Install in this Direction |
Attach the clip as shown in the illustration to install the center pillar garnish LH.
Install the clip.
for 5 Door:
Use the same procedure described for the RH side.
62413A
27.INSTALL LOWER CENTER PILLAR GARNISH RH
62414A
28.INSTALL LOWER CENTER PILLAR GARNISH LH
Use the same procedure described for the RH side.
67871E
29.INSTALL NO. 1 SLIDE DOOR WEATHERSTRIP RH
67872A
30.INSTALL NO. 1 SLIDE DOOR WEATHERSTRIP LH (for 5 Door)
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR OPENING TRIM WEATHERSTRIP (except Wagon)>INSTALLATION
67917C
31.INSTALL REAR DOOR SCUFF PLATE RH
for Standard Roof, Full Cover Type:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>INSTALLATION
for Standard Roof, except Full Cover Type:
Attach the clip and guide to install the rear door scuff plate RH.
Install the 5 screws.
for High Roof, Full Cover Type:
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for Full-trim)>INSTALLATION
for High Roof, except Full Cover Type:
Attach the clip and guide to install the rear door scuff plate RH.
Install the 6 screws.
67918D
32.INSTALL REAR DOOR SCUFF PLATE LH (for 5 Door)
Use the same procedure described for the RH side.
74707
33.INSTALL NO. 1 HAND GRIP FRAME SUB-ASSEMBLY (w/ Hand Rail)
Attach the guide.
Install the No. 1 hand grip frame sub-assembly with the 6 bolts.
74733
34.INSTALL NO. 1 HAND GRIP COVER (w/ Hand Rail)
Attach the clip to install the No. 1 hand grip cover.
73220
35.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH
73210
36.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure described for the LH side.
73233D
37.INSTALL OUTER LAP BELT ANCHOR COVER
73178C
38.INSTALL SEAT BELT ANCHOR COVER CAP
74680
39.INSTALL PILLAR ASSIST GRIP ASSEMBLY B (w/ Assist Grip)
74617A
40.INSTALL ASSIST GRIP PLUG (w/ Assist Grip)
41.INSTALL REAR SEAT ASSEMBLY LH
for Van:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Van)>INSTALLATION
for Commuter, 3-Passenger Seat with 2-Point Type Seat Belt and Headrest:
for Commuter, 3-Passenger Seat with 2-Point Type Seat Belt without Headrest:
for Commuter, 4-Passenger Seat:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, 4-Passenger Seat)>INSTALLATION
for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt and Headrest:
for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest:
42.INSTALL REAR SEAT ASSEMBLY RH
for Commuter, Single-Passenger Seat with 2-Point Type Seat Belt:
for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest:
Use the same procedure described for the LH side.
43.INSTALL FRONT SEAT ASSEMBLY
for Separate Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Separate Seat Type)>INSTALLATION
for Fixed Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Fixed Bench Seat Type)>INSTALLATION
for Sliding Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Sliding Bench Seat Type)>INSTALLATION
62212
44.INSTALL FRONT PILLAR GARNISH LH
62211
45.INSTALL FRONT PILLAR GARNISH RH
Use the same procedure described for the LH side.
74680
46.INSTALL PILLAR ASSIST GRIP ASSEMBLY LH
74680
47.INSTALL PILLAR ASSIST GRIP ASSEMBLY RH
Use the same procedure described for the LH side.
62312B
48.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
49.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
62112
50.INSTALL COWL SIDE TRIM BOARD LH
62111C
51.INSTALL COWL SIDE TRIM BOARD RH
Use the same procedure described for the LH side.
67914B
52.INSTALL FRONT DOOR SCUFF PLATE LH
67912A
53.INSTALL FRONT DOOR OUTSIDE SCUFF PLATE LH
67913B
54.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
67911B
55.INSTALL FRONT DOOR OUTSIDE SCUFF PLATE RH
Use the same procedure described for the LH side.
61890A
56.INSTALL BACK WINDOW GLASS HAMMER ASSEMBLY (w/ Hammer)
57.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)
for 7GR-FKS:
for 1GD-FTV:
58. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (w/ Airbag System)
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
59. PERFORM DIAGNOSTIC SYSTEM CHECK (w/ Airbag System)
60.CHECK SRS WARNING LIGHT (w/ Airbag System)
61.INSPECT SEAT BELT WARNING SYSTEM (w/ Seat Belt Warning System)