Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL SENDER GAUGE ASSEMBLY › from 2019.06
RM35X0E _51 Engine / Hybrid System _079306 1GD-FTV FUEL _0385718 FUEL SENDER GAUGE ASSEMBLY A

1GD-FTV FUEL  FUEL SENDER GAUGE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 83320 1.INSTALL FUEL SENDER GAUGE ASSEMBLY

a.
A439099C01
0,0 0,0 false
V100135

Slide


Set the fuel sender gauge assembly on the fuel tank vent tube assembly. Then slide the fuel sender gauge assembly downward until the 2 claws attach to install it.


b.

Connect the fuel sender gauge assembly connector.


Hide 77010 2.INSTALL FUEL TANK VENT TUBE ASSEMBLY

a.

Apply a light coat of diesel fuel or grease to a new fuel tank vent tube gasket, and install it to the fuel tank sub-assembly.


b.

Install the fuel tank vent tube assembly to the fuel tank sub-assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



c.
A439087C01
2.031,0.583 2.615,0.781 2.615,0.781 2.844,0.781 true 1.469,1.688 1.99,1.938 1.99,1.938 2.188,1.938 true 2.896,0.667 3.104,0.854 0.208,0.188 10 true *a 2.208,1.823 2.417,2.01 0.208,0.188 10 true *a
*a Protrusion
V100135

Hole
V100136

Front of Vehicle


Align the protrusions of the fuel tank vent tube assembly with the holes in the fuel tank sub-assembly.


d.

While pressing down on the fuel tank vent tube assembly, temporarily install the fuel pump gauge retainer.


e.
A439094C01
2.573,2.531 2.573,2.292 true 1.146,0.167 1.375,0.167 1.375,0.167 1.469,0.438 true 1.469,3.115 1.646,3.521 false 1.271,3.271 1.635,3.521 false 1.333,2.813 1.615,2.698 1.615,2.698 1.771,2.698 false 0.656,3.229 1.375,2.969 true 1.115,3.125 0.667,3.229 true 1.167,0.688 1.344,0.688 1.344,0.688 1.427,0.875 true 1.573,3.521 1.885,3.677 0.313,0.156 10 false *a 0.448,3.135 0.646,3.365 0.198,0.229 10 true *b 2.469,2.542 2.729,2.698 0.26,0.156 10 true *c 0.76,0.063 1.146,0.24 0.385,0.177 10 true SST 0.833,0.604 1.156,0.833 0.323,0.229 10 true SST 1.802,2.583 2.031,2.792 0.229,0.208 10 true *a
*a Alignment Mark
*b Groove
*c Insertion Point
V100135

Turn
V100136

Front of Vehicle


Set the 2 claws, 2 bolts and plate of SST on the fuel pump gauge retainer.

SST
09808-14031  (09808-01010, 09808-01030, 09808-01090)
09808-01110  

HINT:

Securely insert the ends of SST into the insertion points in the fuel pump gauge retainer.



f.

While firmly pressing the claws of SST into the insertion points in the fuel pump gauge retainer, tighten the bolts of the claws.


g.

Attach the handle of SST.


h.

Check once more that the tip of SST is securely inserted into the insertion area of the fuel pump gauge retainer as shown in the illustration.


i.

Using SST, rotate the fuel pump gauge retainer so that the protrusions of the fuel pump gauge retainer are aligned with the grooves in the fuel tank sub-assembly to install the fuel tank vent tube assembly to the fuel tank sub-assembly.

NOTICE:
·

Do not use any tools other than SST, such as a screwdriver, etc.

·

Do not use excessive force when pressing down on SST, as the fuel pump gauge retainer will place excessive force on the fuel tank vent tube assembly and be difficult to remove, and parts may be damaged.

·

Be sure to keep the handle level when turning it, as SST may slip off the retainer if the handle is turned at an angle with excessive force.

·

Do not use an impact wrench or turn the handle with excessive force, as parts may be damaged.

·

If SST slips off the fuel pump gauge retainer, loosen the bolts and reattach SST to the fuel pump gauge retainer.




j.
A439089C01
1.396,2.104 1.813,2.104 true 1.271,2.302 1.635,2.302 true 1.094,2.75 1.219,2.75 1.219,2.75 1.396,2.563 true 2.177,2.656 2.635,2.615 2.635,2.615 2.177,2.563 true 0.469,4.021 0.594,4.021 0.594,4.021 0.844,3.667 true 2.51,3.646 2.792,3.271 2.792,3.271 2.927,3.271 true 1.219,2 1.458,2.198 0.24,0.198 10 false *a 1.104,2.219 1.333,2.427 0.229,0.208 10 false *b 2.656,2.521 2.854,2.698 0.198,0.177 10 false *c 0.938,2.656 1.167,2.844 0.229,0.188 10 false *d 0.302,3.938 0.531,4.135 0.229,0.198 10 false *e 0.792,3.135 0.99,3.333 0.198,0.198 10 false *f 2.26,3.146 2.5,3.385 0.24,0.24 10 false *g 2.969,3.177 3.177,3.333 0.208,0.156 10 false *e
*a Fuel Tube Joint
*b Tube Joint Clip
*c O-Ring
*d Fuel Tank Vent Tube Assembly
*e Collar
*f CORRECT
*g INCORRECT


Insert the fuel tank main tube sub-assembly and fuel tank return tube into the plugs of the fuel tank vent tube assembly and fix them in place with the 2 tube joint clips.

NOTICE:
·

Check that there are no scratches or foreign objects on the connecting parts.

·

Check that the fuel tube joints are inserted securely.

·

Check that the tube joint clips are on the collars of the fuel tube joints.

·

After installing the tube joint clips, check that the fuel tube joints cannot be pulled off.

·

Be careful not to damage any clips.

If a clip is damaged, replace it.




Hide 77285R 3.INSTALL NO. 1 FUEL TUBE CLAMP

Hide 58759A 4.INSTALL FUEL TANK INSPECTION HOLE COVER

a.

Connect the connector to the fuel suction with pump and gauge tube assembly.


b.

Install the rear floor service hole cover with the 4 bolts.


c.

except Wagon:

i.

Install the rear floor board.


ii.

Return the rear floor carpet to its original position.



d.

for Wagon:

i.

Return the rear floor carpet to its original position.


ii.

Return the rear seat assembly LH to its original position.



Hide 5.INSTALL REAR SEAT ASSEMBLY (except Wagon)

·
·

for Commuter, 3-Passenger Seat with 2-Point Type Seat Belt without Headrest:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, 3-Passenger Seat with 2-Point Type Seat Belt without Headrest)>INSTALLATION

·
·
·
·

for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest:

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest)>INSTALLATION


Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 7. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART