Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2019.06
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0385516 ECD SYSTEM(w/ DPF) D

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  VEHICLE CONTROL HISTORY  


DESCRIPTION (ECD SYSTEM)


·

Vehicle Control History is a function that captures and stores ECU data when triggered by specific vehicle behavior.

·

If the customer states that the engine stalled or will not start, it may be possible to diagnose the cause of the malfunction by checking the vehicle history information and freeze frame data.

·

The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.

·

The stored data items for Vehicle Control History Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The contents of the Freeze Frame Data is almost the same as that of the Data List.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DATA LIST / ACTIVE TEST



PRECAUTIONS (ECD SYSTEM)


·

As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History before performing any inspections.

·

As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.



CHECK VEHICLE CONTROL HISTORY (ECD SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 1055
HINT:

It is also possible to display Vehicle Control History during the Health Check, if "Store All Data" is selected.


Vehicle Control History Item
Code Item Trigger Description Stored Group Reference Inspection Procedure Link
X0800 Engine Stall
Detection Condition (Engine Stall)
·

Prerequisite Conditions: The engine is running (after engine is judged to be difficult to start)

·

Detection Conditions: The engine speed decreases to 200 rpm or less, or stops

·

Duration: 0.5 seconds or more


08 Flowchart [Engine difficult to start or stalling] step 3 (Click here)
The engine stalled due to factors other than the operation of the ignition switch
X0806 Engine Stall (Fuel Pressure Low) It is judged that the engine is stalled due to a drop in fuel pressure 08 Flowchart [Engine difficult to start or stalling] step 3 (Click here)
X0810 Engine Difficult to Start (Engine Starting Time Long)
Detection Condition (Engine Starting Time Long)
·

Prerequisite Conditions: STA signal is ON

·

Detection Conditions: The engine speed is less than 500 rpm for a long period of time (the starting time is long or the engine does not start)

·

Duration: Refer to Engine Difficult to Start Duration Judgment Region illustration


09 Flowchart [Engine difficult to start or stalling] step 3 (Click here)
X0811 Engine Difficult to Start (Engine Stall Immediately After Starting)
Detection Condition (Engine Stall Immediately After Starting)
·

Prerequisite Conditions: Within 2 seconds after the engine has started (engine speed is 500 rpm or more) and the engine coolant temperature is -15°C (5°F) or more

·

Detection Conditions: The engine speed decreases to 200 rpm or less (immediately after starting, the engine speed decreases or the engine stalls)

·

Duration: -


09 Flowchart [Engine difficult to start or stalling] step 3 (Click here)
The engine speed decreases or the engine stalls immediately after starting
X0812 Engine Difficult to Start (Immobiliser) Engine difficult to start due to immobiliser 09 Flowchart [Engine difficult to start or stalling] step 3 (Click here)
X0821 Rough Idle #1
Detection Condition (Rough Idle)
·

Prerequisite Conditions: The engine is idling with the vehicle is stopped and the accelerator pedal is fully released

·

Detection Conditions: It is judged that combustion is unstable due to the instantaneous change in engine speed for each cylinder

·

Duration: Depending on the combustion status, between 2 and 10 seconds


03 Flowchart [Rough idling or excessive vibration] step 4 (Click here)
Idling is rough due to unstable combustion in the No. 1 cylinder
X0822 Rough Idle #2 Idling is rough due to unstable combustion in the No. 2 cylinder 03 Flowchart [Rough idling or excessive vibration] step 4 (Click here)
X0823 Rough Idle #3 Idling is rough due to unstable combustion in the No. 3 cylinder 03 Flowchart [Rough idling or excessive vibration] step 4 (Click here)
X0824 Rough Idle #4 Idling is rough due to unstable combustion in the No. 4 cylinder 03 Flowchart [Rough idling or excessive vibration] step 4 (Click here)
X082A Rough Idle (Plural Cylinders) Idling is rough due to multiple cylinders
As more than one cylinder is affected, the EGR system, fuel system, etc. is suspected
03 Flowchart [Rough idling or excessive vibration] step 4 (Click here)
X082D Rough Idle (Compression Leakage) Idling is judged to be rough due to compression leakage 03 Flowchart [Rough idling or excessive vibration] step 4 (Click here)
X0843 Engine Lack of Power (Boost Pressure Low) Engine output is insufficient due to a drop in boost pressure 04 Flowchart [Lack of power or hesitation] step 2 (Click here)
X0846 Engine Lack of Power (Fuel Pressure Low) Engine output is insufficient due to a drop in fuel pressure 04 Flowchart [Lack of power or hesitation] step 2 (Click here)
X0847 Engine Lack of Power (Mass Air Flow Low) Engine output is insufficient due to a drop in mass air flow 04 Flowchart [Lack of power or hesitation] step 2 (Click here)
X0848 Engine Lack of Power (Engine Coolant Temperature High) Engine output is insufficient due to the load being limited during high coolant temperature 04 Flowchart [Lack of power or hesitation] step 2 (Click here)
X0850 Engine Oil Pressure Low The engine oil pressure is low 05 - -
X0851 Engine Coolant Temperature High The engine coolant temperature is high (overheating) 05 - -
X0852 Engine RPM High The engine speed is high (over revving) 05 - -
X085D DPF Clogged Level 1 DPF regeneration is insufficient and PM accumulation requires PM Forced Regeneration 05 - -
X085E DPF Clogged Level 2 DPF regeneration is insufficient and PM accumulation requires PM Forced Regeneration 05 - -
X0860 Air-Fuel Ratio Too High The air-fuel ratio is too rich 05 Flowchart [Black smoke emitted] (Click here)
X0861 Clogged Fuel Filter The fuel filter cap with element is clogged 05 Refer to the P00BB00 inspection procedure (Click here)

Engine Difficult to Start Duration Judgment Region (Engine Starting Time Long) (X0810)
A220316E34
0.314,1.64 1.192,1.824 0.878,0.184 10 Starting Time 1.276,0.37 1.960,0.554 0.684,0.184 10 (Seconds) 3.844,1.136 5.000,1.486 1.156,0.350 10 Region Indicating Malfunction 6.384,2.761 6.665,2.959 0.281,0.198 10 (°C) 1.43,2.26 1.553,2.437 0.123,0.177 10 2 1.892,2.78 2.132,2.936 0.239,0.156 10 -30 3.517,2.78 3.715,2.950 0.198,0.170 10 20 5.198,2.78 5.410,2.964 0.211,0.184 10 80 3.518,3.178 5.368,3.362 1.850,0.184 10 Engine Coolant Temperature

Stored Data
Stored Group Number of Records Number of Freeze Frame Points Multi Freeze Frame Data Sampling Period Note
03 1 code
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.

·

If rough idle codes other than Rough Idle (Low Frequency) code X082E are stored, data for code X082E will not be overwritten.



7 points (1 point at detection + 6 points before detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal.
04 1 code
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



7 points (1 point at detection + 6 points before detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal.
05 4 codes
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



1 point (multi freeze frame data not available) -
·

The data can be cleared by using the GTS.

·

The data cannot be cleared by disconnecting the cable from the negative (-) battery terminal.


08 2 codes
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



12 points (1 point at detection + 8 points before detection + 3 points after detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds
·

The data can be cleared by using the GTS.

·

The data cannot be cleared by disconnecting the cable from the negative (-) battery terminal.


09 1 code
HINT:
·

If the detection conditions for a code that is not currently stored are met, the code will be stored.

·

If the detection conditions for a code that is currently stored are met again in the same trip, the code will not be overwritten.

·

If the detection conditions for a code that is currently stored are met again in a different trip, the code will be overwritten.



7 points (1 point at detection + 3 points before detection + 3 points after detection)
HINT:

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


0.5 seconds The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal.

HINT:
·

Multi Freeze Frame Data makes it possible to display the engine condition (ECU data) both before and after the trigger detection point.

·

The number of available points differs depending on the stored group.

·

When the value of a data item does not change across all points, only the value at the detection point will be displayed.


A405050E06
2.948,1.552 2.844,1.552 2.844,1.552 2.844,1.385 false 0.156,0.083 2.917,0.323 2.76,0.24 12 false Stored Group 03, 04 1.854,0.635 3.458,0.906 1.604,0.271 10 false Point Before Detection 1.667,2.344 3.802,2.656 2.135,0.313 10 false Recording Time Before Detection 1.094,1.927 3.063,2.188 1.969,0.26 10 false Sampling Cycle (0.5 seconds) 3.542,0.104 5.135,0.396 1.594,0.292 10 false Trigger Detection Point 2.969,1.458 4.177,1.948 1.208,0.49 10 false Freeze Frame Data which can be read

A414224E03
5.406,1.688 5.208,1.615 5.208,1.615 5.208,1.479 false 0.302,0.156 1.677,0.354 1.375,0.198 12 false Stored Group 08 4.156,0.135 5.677,0.323 1.521,0.188 10 false Trigger Detection Point 5.604,0.458 7,0.656 1.396,0.198 10 false Point After Detection 1.885,0.458 3.479,0.688 1.594,0.229 10 false Point Before Detection 2.979,1.958 4.885,2.229 1.906,0.271 10 false Sampling Cycle (0.5 seconds) 5.448,1.615 6.875,2.01 1.427,0.396 10 false Freeze Frame Data which can be read 1.542,2.417 3.667,2.656 2.125,0.24 10 false Recording Time Before Detection 5.167,2.448 7.135,2.677 1.969,0.229 10 false Recording Time After Detection

A412793E01
5.063,1.625 4.927,1.625 4.927,1.625 4.833,1.458 false 3.302,0.177 5.073,0.396 1.771,0.219 10 false Trigger Detection Point 1.573,0.552 3.281,0.813 1.708,0.26 10 false Point Before Detection 4.833,0.542 6.594,0.75 1.76,0.208 10 false Point After Detection 2.031,1.948 4.115,2.198 2.083,0.25 10 false Sampling Cycle (0.5 seconds) 0.198,0.146 1.917,0.417 1.719,0.271 12 false Stored Group 09 5.135,1.563 6.375,2.104 1.24,0.542 10 false Freeze Frame Data which can be read 1.406,2.427 3.802,2.646 2.396,0.219 10 false Recording Time Before Detection 4.458,2.427 6.781,2.656 2.323,0.229 10 false Recording Time After Detection

Only 1 measurement point can be displayed for stored group 05 Freeze Frame Data.




CLEAR VEHICLE CONTROL HISTORY (ECD SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) (Clear).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55
NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.




VEHICLE CONTROL HISTORY FREEZE FRAME DATA (ECD SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

e.

Select a vehicle control history item to access the applicable freeze frame data.


f.

Check the freeze frame Data recorded with the Vehicle Control History.

Vehicle Control History Data
A441050

A441051



CHECK VEHICLE CONTROL HISTORY (CHARGING SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55
Vehicle Control History Item
Code Tester Display Measurement Item Diagnostic Note
X0600 Auxiliary Battery Voltage Low at Start History of low battery voltage at engine control system start -
X0603 Auxiliary Battery Discharge at Running History of battery becoming discharged while vehicle being driven -



CLEAR VEHICLE CONTROL HISTORY (CHARGING SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) (Clear).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55
NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.




VEHICLE CONTROL HISTORY FREEZE FRAME DATA (CHARGING SYSTEM)


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

e.

Select a vehicle control history item to access the applicable freeze frame data.


f.

Check the freeze frame Data recorded with the Vehicle Control History.

Vehicle Control History Data
GTS Display Description
Total Distance Traveled Driving distance
Total Distance Traveled - Unit Unit of driving distance
Initial Engine Auxiliary battery Minimum Voltage Minimum voltage at engine start
Alternator Voltage - Non Active Test Requested voltage when the regulator forced operation is not executed
Alternator Output Duty Ratio LIN terminal output (power generation rate)
Auxiliary Battery Voltage Battery voltage
(+B, +B2 terminal)
Auxiliary Battery Integrated Current Battery capacity taking into account battery deterioration.
Smoothed Value of Auxiliary Battery Temperature Calculated battery fluid temperature by battery fluid temperature sensor
Auxiliary Battery Charge Rate Battery charge percentage calculated by battery sensor
Auxiliary Battery Charging Rate Accuracy Accuracy of battery charge percentage calculated by battery sensor
Auxiliary Battery Charging Capacity Battery charging capacity calculated by battery sensor
Charging Control Mode Status of charging control
Average Vehicle Speed during Trip Average vehicle speed after engine starts during the current trip
Auxiliary Battery Integrated Current during Trip Integrated current value detected by the battery state sensor during the current trip
Auxiliary Battery Charging Integrated Current when Trip before Last Integrated current charged during the previous trip
Auxiliary Battery Discharging Integrated Current when Trip before Last Integrated current discharged during the previous trip
Auxiliary Battery Capacity after IG ON Battery capacity immediately after ignition switch ON
Auxiliary Battery Capacity after IG OFF Battery capacity immediately after ignition switch off
Estimated Open Ended Auxiliary Battery Voltage when IG OFF Estimated battery release voltage calculated when ignition switch is off by the battery sensor
Auxiliary Battery Average Current during IG OFF Average current while parked (average value of current consumed from when the ignition switch is off until lit is on (IG))
IG OFF Time just before IG ON Parking duration (duration from when the ignition switch is off until it is on (IG))
Auxiliary Battery Average Current when Auxiliary Battery Voltage Low (during IG OFF) Average current when system judges that voltage is low while parked (average current value when the ignition switch is off until the system judges the voltage is low while parked)
IG OFF Time when Auxiliary Battery Voltage Low (during IG OFF) Parking duration when system judges that voltage is low while parked (duration from when the ignition switch is off until the system judges the voltage is low while parked)
Elapsed Time during Auxiliary Battery Voltage Low Duration that the voltage detected by the battery state sensor while the vehicle is in motion is below the threshold (example: 11 V)
Average Engine Speed Average engine speed after engine starts during the current trip



VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)


HINT:

A part of the control history can be confirmed using the vehicle control history.