| Malfunction Condition | Main Trouble Area | Related Trouble Area |
|---|---|---|
·
Lack of power caused by abnormal fuel injection volume (fuel supply pump assembly malfunction, injector assembly malfunction, etc.) ·
Lack of power caused by intake air volume shortage (turbocharger malfunction or exhaust manifold converter sub-assembly blocked) |
(a) Injector assembly malfunctions
·
Injector sliding malfunction ·
Injector stuck closed ·
Injector stuck open ·
Deposits in injector ·
Injector circuit malfunction (b) Abnormal common rail pressure ·
Pre-stroke control valve (c) Abnormal intake air volume ·
Intake system leakage or clogged ·
Turbocharger sub-assembly ·
Exhaust manifold converter blockage ·
EGR valve does not close ·
Throttle valve does not open |
·
Pressure discharge valve ·
Intake air system blockage ·
EGR system ·
Fuel filter element assembly is clogged ·
Throttle valve ·
Mass air flow meter sub-assembly ·
Compression pressure ·
Injector compensation code ·
Fuel leak ·
Glow plug assembly ·
Fuel pressure sensor ·
Manifold absolute pressure sensor ·
Vacuum hose connection for manifold absolute pressure sensor ·
Vehicle modifications ·
Clutch disc wear ·
Low quality fuel ·
Frozen fuel ·
ECM |
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
Check that the vehicle has not been modified in any way prior to the vehicle inspection.
This troubleshooting procedure checks for the cause of an obvious lack of engine power while the vehicle is being driven (such as the maximum speed being extremely low).
Faults and Symptoms of Common Rail Diesel Components
Engine Control
| Main fault | Decrease in performance (foreign matter is stuck) |
| Symptoms | Lack of power, black smoke |
| Data List | Mass Air Flow Sensor |
|
|
| Symptom and Corresponding Main Fault | ·
Lack of power (no black smoke) due to air cleaner filter element blockage or crushed or leaking air duct ·
Black smoke (no lack of power) due to leakage between the turbo and intake manifold |
| Data List | ·
Intake Manifold Absolute Pressure ·
Target Boost Pressure When the accelerator is fully depressed, if Intake Manifold Absolute Pressure is 20 kPa lower than Target Boost Pressure for more than 5 seconds, then a lack of power will be felt. ·
Mass Air Flow Sensor |
| Main fault | ·
Air leak in the turbocharged air passage ·
Turbocharger sub-assembly (turbine, bearing, variable nozzle) |
| Symptoms | Lack of power (when vehicle is starting, under heavy load)
(Black smoke is not emitted when racing while vehicle is stopped) |
| Data List | Intake Manifold Absolute Pressure, Target Boost Pressure
·
When the accelerator is fully depressed, if Intake Manifold Absolute Pressure is 20 kPa lower than Target Boost Pressure for more than 5 seconds, then a lack of power will be felt. ·
With the ignition switch ON or during idling, Intake Manifold Absolute Pressure = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and Intake Manifold Absolute Pressure becomes higher than atmospheric pressure. ·
Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions. |
| Main fault | Blockage |
| Symptoms | Lack of power (high engine speed, under heavy load) |
| Data List | Intake Manifold Absolute Pressure, Target Boost Pressure
When the accelerator is fully depressed, if Intake Manifold Absolute Pressure is 20 kPa lower than Target Boost Pressure for more than 5 seconds, then a lack of power will be felt. |
| Main fault | Glow system malfunction |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) |
| Diagnostic Point | ·
Measure the resistance of the glow plug assembly ·
Check the glow plug indicator light |
| Main fault | Damaged, seized up |
| Symptoms | Cannot crank, crank speed is low, strange noise |
| Main fault | Loss of compression |
| Symptoms | Rough idle (lack of power always) |
| Data List | Engine Speed Cylinder
·
When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression. Injection Feedback Value ·
When an Injector Feedback Value is more than 5 mm3/st, there may be a malfunction in the corresponding cylinder. |
Diesel Injection
| Main fault | - |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Fuel Pressure (High), Target Fuel Pressure (High)
·
Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)). ·
If the fuel pressure is 20000 kPag below the target pressure, then a lack of power will be felt. ·
If the fuel pressure is below 25000 kPag, then idling will be rough.
|
| Diagnostic Trouble Code | Even if Fuel Pressure (High) is below Target Fuel Pressure (High), a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power |
| Data List | Fuel Pressure (High), Target Fuel Pressure (High)
·
Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)). ·
If the fuel pressure is 20000 kPag below the target pressure, then a lack of power will be felt. ·
If the fuel pressure is below 25000 kPag, then idling will be rough.
|
| Diagnostic Trouble Code | Even if Fuel Pressure (High) is below Target Fuel Pressure (High), a DTC will not be stored. |
| Main fault | Blockage |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking |
| Data List | Injection Feedback Value
·
When an Injector Feedback Value is more than 5 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute. |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power |
| Data List | Fuel Pressure (High), Target Fuel Pressure (High)
·
Fuel Pressure (High) is within 5000 kPag of Target Fuel Pressure (High) during idling with the engine warmed up (engine coolant temperature is higher than 75°C (167°F)). |
| Diagnostic Trouble Code | When the fuel pressure sensor has a fault, some DTCs may be stored. |
| Main fault | - |
| Symptoms | Difficult to start, rough idle (especially when cold) |
Diesel EGR
| Main fault | ·
Does not move smoothly ·
Does not close fully |
| Symptoms | ·
Rough idle ·
EGR valve stuck closed: A loud turbocharger sound. ·
EGR valve stuck open: Difficult to start (does not stall), black smoke, white smoke (when engine is cold), lack of power, jerking (If there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt. Also, when racing the engine, there will be some black smoke). |
| Data List | Actual EGR Valve Position No.1, Target EGR Valve Position No.1
·
Generally, Actual EGR Valve Position No.1 = Target EGR Valve Position No.1 +/-5% (fully closed: 0%, fully open: 100%). ·
Using the EGR valve Active Test, check whether Actual EGR Valve Position No.1 follows Target EGR Valve Position No.1 (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs). ·
EGR valve is fully closed when the ignition switch is ON (engine stopped). ·
EGR valve opens to the halfway point at idling after the engine is warmed up. ·
When the EGR valve does not close, Mass Air Flow Sensor (Mass Air Flow) decreases when the vehicle is accelerated at full throttle. Intake Manifold Absolute Pressure also decreases in comparison to Target Boost Pressure, however there is not a large difference. EGR Close Learning Value Bank 1 ·
When leaving the vehicle idling, the normal range of EGR Close Learning Value Bank 1 is 0 to 1 V. ·
In cases when EGR Close Learning Value Bank 1 is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close. |
Diesel Throttle
| Main fault | Stuck, does not move smoothly |
| Symptoms | ·
Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed. ·
Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur. |
| Data List | Actual Throttle Position Bank 1
·
0%: Fully closed ·
100%: Fully open ·
When the ignition switch is ON (engine stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily. |
Data List Related to Lack of Power
Depending on the vehicle model, the applicable Data List items may vary. Data List items other than the ones used in the diagnostic procedure are for reference only.
Engine Speed
Intake Manifold Absolute Pressure
Mass Air Flow Sensor
Intake Air Temperature
Coolant Temperature
Target Fuel Pressure (High)
Fuel Pressure (High)
Injection Feedback Value #1 to #4
Target Injection Volume
Actual Throttle Position Bank 1
Target EGR Valve Position No.1
Actual EGR Valve Position No.1
Vehicle Control History Freeze Frame Data Items Related to Lack of Power
The frequency of the malfunction can be determined by confirming the number of times the symptom occurred.
Engine Lack of Power Count (Boost Pressure Low)
Engine Lack of Power Count (Fuel Pressure Low)
Engine Lack of Power Count (Mass Air Flow Low)
Engine Lack of Power Count (Engine Coolant Temperature High)
Explanation of Symptom
| Lack of Power | The power of the diesel engine is determined by the quantity of injected fuel and the quantity of intake air.
The quantity of injected fuel is determined by the fuel pressure and the amount of time the injector assembly is open. Basically, the fuel pressure is controlled so that it reaches the target fuel pressure. The throttle valve does not restrict air flow volume, so the manifold absolute pressure is almost the same as atmospheric pressure when idling. At more than approximately 1500 rpm, the turbo starts to operate causing the manifold absolute pressure to become higher than atmospheric pressure. The manifold absolute pressure is controlled so that it reaches the Target Boost Pressure when accelerating the vehicle at full throttle. Also, when accelerating the vehicle at full throttle, the throttle is fully open and the EGR valve is fully closed, preserving the mass air flow. |
After replacing an injector assembly, the ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
If any other DTCs are output, perform troubleshooting for those DTCs first.
Make sure to reproduce the conditions present when the malfunction occurred.
Using the GTS, read the Data List to confirm the engine operating conditions. This information can be useful when troubleshooting.
The vehicle condition when the problem symptoms occurred can be determined using the Vehicle Control History.
As the Vehicle Control History data may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
If the problem symptoms do not recur, attempt to reproduce the symptoms and conditions when the malfunction occurred based on the result of the customer problem analysis and Vehicle Control History. Place the priority on confirming the symptoms.
When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
The suspected cause of the problem symptoms can be determined using the codes, items, and Freeze Frame Data within the Vehicle Control History.
When confirming the Freeze Frame Data, be sure to check all multi Freeze Frame Data.
When confirming the Freeze Frame Data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
If the malfunction is currently occurring, use the Data List to confirm the current vehicle condition. By using the Data List, more detailed vehicle information can be confirmed than by using the Vehicle Control History Freeze Frame Data by itself.
As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.
If the engine is started immediately after reconnecting the battery terminal, the engine may stall immediately after it starts due to the intercommunication process between each ECU. For this reason, when starting the engine after reconnecting the battery terminal, first turn the ignition switch to ON and then wait several seconds for the communication process to complete before starting the engine.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| Engine related DTCs are output | B |
A
B
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
It is also possible to display vehicle control history during the Health Check, if "Store All Data" is selected.
Confirm if any data relating to the problem symptoms exists in the Vehicle Control History.
The vehicle condition when the problem symptoms occurred can be determined by confirming the Vehicle Control History Freeze Frame Data.
As the Vehicle Control History data may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
Using information from the customer about when the problem symptom occurred, find the Freeze Frame Data with the appropriate Key Cycle, Total Distance Traveled, etc., to find vehicle history that may be related to the problem symptoms.
Check the vehicle control history code and freeze frame data.
| Vehicle Control History | Vehicle Control History Freeze Frame Data | Suspected Area | Proceed to |
|---|---|---|---|
| Engine Lack of Power (Boost Pressure Low) is stored
(Vehicle Control History Code: X0843) |
- | ·
Intake system hose disconnected or cracked ·
Turbocharger sub-assembly vane stuck fully open ·
Manifold absolute pressure sensor ·
Manifold absolute pressure sensor out of range ·
Atmospheric pressure sensor (built into ECM) ·
Abnormal pressure difference between the atmospheric pressure sensor and manifold absolute pressure sensor ·
EGR valve stuck closed |
A |
"MAF/Estimate MAF Ratio" in freeze frame data is 1.4 or more
|
Intake air leak due to intake pipe disconnection or cracks between the turbocharger sub-assembly and intercooler assembly or between the intercooler assembly and intake manifold. | B | |
"MAF/Estimate MAF Ratio" in freeze frame data is below 0.6
|
Air entering due to intake pipe disconnection or cracks between the turbocharger sub-assembly and intercooler assembly or between the intercooler assembly and intake manifold. | ||
| Engine Lack of Power (Fuel Pressure Low) is stored
(Vehicle Control History Code: X0846) |
- | ·
Pre-stroke control valve sticking ·
Fuel leak ·
Fuel filter element assembly clogged ·
Fuel pressure sensor (built into common rail assembly) |
C |
| Engine Lack of Power (Mass Air Flow Low) is stored
(Vehicle Control History Code: X0847) |
- | ·
Intake system clogged ·
EGR valve stuck closed ·
Deterioration of mass air flow meter sub-assembly (foreign matter present on sensor element etc.) |
D |
| Engine Lack of Power (Engine Coolant Temperature High) is stored
(Vehicle Control History Code: X0848) |
- | ·
Engine coolant leak ·
Radiator assembly clogged ·
Engine coolant temperature sensor ·
Engine coolant temperature sensor out of range or stuck ·
Fan |
- |
| The malfunction is not currently occurring and there is no Vehicle Control History related to the problem symptoms stated by the customer. | E | ||
| The malfunction is currently occurring and there is no Vehicle Control History related to the problem symptoms stated by the customer. | F | ||
A
B
C
D
E
F
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Lack of Power.
With no load after the engine is warmed up, take a snapshot when idling and at 4000 rpm.
A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
The shift lever should be in neutral and the A/C switch and all accessory switches should be off.
| Proceed to |
|---|
| NEXT |
NEXT
Enter the following menus: Powertrain / Engine / Data List / Diesel Lack of Power.
Check for a lack of power during the driving test.
A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.
Move the shift lever to 2nd gear and accelerate the vehicle with the accelerator pedal fully depressed. Then, check the Data List with the engine warmed up and idling (the shift lever should be in neutral and the A/C switch and all accessory switches should be off).
Obey all laws and regulations, and pay attention to traffic conditions while driving the vehicle.
| Result | Proceed to |
|---|---|
| Apparent lack of power is present | A |
| Apparent lack of power is not present | B |
A
B
Check Intake Manifold Absolute Pressure and Mass Air Flow Sensor in the snapshot taken in procedure 3 when the engine was running at 4000 rpm with no load.
| Result | Proceed to |
|---|---|
| Mass Air Flow Sensor 84 gm/sec or more and Intake Manifold Absolute Pressure 105 kPa or higher*1 | A |
| Intake Manifold Absolute Pressure is below 90 kPa*2 | B |
| Except above*3 | C |
The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
*1: There may be a problem in the fuel injection system or intake system.
*2: There may be a problem in the turbocharger system.
*3: There may be a problem in the intake system or a problem with the EGR valve (valve stuck open or valve does not close).
A
B
C
Check Intake Manifold Absolute Pressure, Fuel Pressure (High) and Target Fuel Pressure (High) in the snapshot taken in procedure 4 when the vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.
| Result | Proceed to |
|---|---|
| Intake Manifold Absolute Pressure is below 170 kPa at an engine speed of 3000 rpm | A |
| Difference between Fuel Pressure (High) and Target Fuel Pressure (High) is 20000 kPag or more | B |
| Except above | C |
The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc. Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
The engine speed must be 1500 rpm or less before performing the inspection in which the accelerator pedal is fully depressed and the engine is accelerated to a speed of 3000 rpm.
If the turbocharger movement is not smooth, etc., the value of Intake Manifold Absolute Pressure in the snapshot taken during lack of power will not reach the target value. When the accelerator pedal is fully depressed and the engine speed is 3000 rpm, the Intake Manifold Absolute Pressure should be higher than 190 kPa.
A
B
C
Check for air leaks and blockages between the air cleaner case and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.
Inspect the intake system, especially hoses and pipes between the air cleaner filter element sub-assembly and turbocharger sub-assembly.
Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
Using your hand, check whether the pipes and hoses in the intake system are securely connected.
By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.
Check for any modifications in the intake system made by the user.
No leakage or blockage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clean the fuel filter case and replace the fuel filter element assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT
Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the injector assemblies of all cylinders.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL
When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.
Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| NEXT |
NEXT
Register the injector compensation code.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION
| Tester Display |
|---|
| Injector Compensation |
Perform the injector pilot quantity learning.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION
| Tester Display |
|---|
| Pilot Quantity Learning |
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Confirm the situation in which the lack of power was experienced by the customer again, and compare the driving feeling under the same conditions using a similar vehicle with the same engine while collecting data with the GTS.
Confirm the state of the following conditions when the lack of power was experienced.
Accelerator pedal position (vehicle load)
Vehicle speed
Engine coolant temperature
Ambient temperature
Driving conditions before the lack of power occurred
Climate
Road and traffic conditions
When (what day) the problem was noticed
Whether the problem occurs suddenly or gradually
How often the problem occurs
Why the customer felt there is a lack of power (e.g. the customer compared their vehicle with another vehicle, somebody told the customer that their vehicle has a lack of power, etc.)
Level of lack of power (slight or drastic)
| Result | Proceed to |
|---|---|
| Significant difference is found | A |
| Significant difference is not found | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Atmospheric Pressure and Intake Manifold Absolute Pressure.
| Tester Display |
|---|
| Atmospheric Pressure |
| Intake Manifold Absolute Pressure |
Compare Intake Manifold Absolute Pressure to Atmospheric Pressure when the ignition switch is ON (do not start the engine).
Difference between Intake Manifold Absolute Pressure and Atmospheric Pressure is less than 8 kPa.
If Intake Manifold Absolute Pressure and Atmospheric Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.
| Result | Proceed to |
|---|---|
| Intake Manifold Absolute Pressure and Atmospheric Pressure have same value | A |
| Intake Manifold Absolute Pressure is different from actual atmospheric pressure | B |
| Atmospheric Pressure is different from actual atmospheric pressure | C |
A
B
C
Check for air leaks and blockages between the air cleaner cap and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.
| Result | Proceed to |
|---|---|
| Leaks and/or blockages exist in the intake system | A |
| No leaks or blockages in the intake system | B |
Inspect the intake system, especially hoses and pipes between the air cleaner filter element sub-assembly and turbocharger sub-assembly.
Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
Using your hand, check whether the pipes and hoses in the intake system are securely connected.
When inspecting for a clogged intake system (cause of low Intake Manifold Absolute Pressure), check the following points:
- Clogged air cleaner filter element
- Clogged intake hose
- Diesel throttle valve stuck in closed position
Check for any modifications in the intake system made by the user.
A
B
Repair or replace the malfunctioning part in the intake system.
| Proceed to |
|---|
| NEXT |
NEXT
Vehicle performance is normal. There is no problem at this point in time. However, if the problem reoccurs, ask the customer to explain in detail the situation in which the problem occurred. The best course may be to have the customer ride in another vehicle with the same specifications to understand that there is no problem with the customer's vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Check the lack of power (turbocharger system).
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).
| Tester Display |
|---|
| Target Fuel Pressure (High) |
| Fuel Pressure (High) |
With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.
Check the Target Fuel Pressure (High) and Fuel Pressure (High) value.
| Result | Proceed to |
|---|---|
| While idling the vehicle, "Fuel Pressure (High)" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1 | A |
| "Fuel Pressure (High)" is normal while idling the vehicle, but "Fuel Pressure (High)" does not follow "Target Fuel Pressure (High)" when the accelerator pedal is fully depressed in 2nd gear*2 | |
| Except above | B |
*1: The cause may be a squashed or blocked fuel pipe or hose.
*2: The cause may be a clogged fuel filter element assembly.
A
B
Repair or replace the clogged (including frozen fuel) fuel pipe.
Replace the fuel filter element assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT
If "Fuel Pressure (High)" does not follow "Target Fuel Pressure (High)" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Bleed the air from the fuel system.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL FILTER>REPLACEMENT
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Target Fuel Pressure (High) and Fuel Pressure (High).
| Active Test Display |
|---|
| Test the Fuel Leak |
| Data List Display |
|---|
| Target Fuel Pressure (High) |
| Fuel Pressure (High) |
Take a snapshot with the GTS during the Active Test.
Measure the difference between the target fuel pressure (Target Fuel Pressure (High)) and the actual fuel pressure (Fuel Pressure (High)) when the "Test the Fuel Leak" Active Test is performed.
In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPag.
"Target Fuel Pressure (High)" is the target fuel pressure controlled by the ECM.
"Fuel Pressure (High)" is the actual fuel pressure.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the fuel supply pump assembly.
Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the manifold absolute pressure sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check for air leaks and blockages between the air cleaner cap and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.
| Result | Proceed to |
|---|---|
| No leaks or blockages in the intake system | A |
| Leaks and/or blockages exist in the intake system | B |
Inspect the intake system, especially hoses and pipes between the air cleaner filter element sub-assembly and turbocharger sub-assembly.
Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.
Using your hand, check whether the pipes and hoses in the intake system are securely connected.
By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.
Make sure that the hose between the manifold absolute pressure sensor and intake manifold is not loose or disconnected.
Check for any modifications in the intake system made by the user.
A
B
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.
| Tester Display |
|---|
| Mass Air Flow Sensor |
Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Valve Close Bank 1 / Data List / Mass Air Flow Sensor.
| Active Test Display |
|---|
| Activate the EGR Valve Close Bank 1 |
| Data List Display |
|---|
| Mass Air Flow Sensor |
Read the Mass Air Flow Sensor value when the EGR valve is closed using the Active Test function.
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.
| Active Test | Result | Proceed to |
|---|---|---|
| Activate the EGR Valve Close Bank 1:
OFF to Close |
Mass Air Flow Sensor value does not change | A |
| Mass Air Flow Sensor value changes | B |
As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.
The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric EGR control valve assembly or mass air flow meter sub-assembly.
| EGR Valve Condition (Opening) | Measuring Condition | Mass Air Flow Sensor (Reference) |
|---|---|---|
| Open (41%) | ·
Atmospheric pressure: 101 kPa ·
Engine coolant temperature: 75°C (167°F) |
3 to 7 gm/sec |
| Closed (0%) | 10 to 21 gm/sec |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Mass Air Flow Sensor.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
Start the engine and read the value when 30 seconds has elapsed.
| Engine Speed | Mass Air Flow Sensor |
|---|---|
| Idling | ·
0.5 to 15 gm/sec (EGR on) ·
10 to 21 gm/sec (EGR off) |
| 3000 rpm (without load) | ·
43 to 89 gm/sec (EGR on) ·
72 to 117 gm/sec (EGR off) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.
| Tester Display |
|---|
| Mass Air Flow Sensor |
Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / Mass Air Flow Sensor and EGR Cooler Bypass Position.
Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.
| Active Test Display |
|---|
| Activate the VSV for EGR Cooler Bypass |
| Data List Display |
|---|
| Mass Air Flow Sensor |
| EGR Cooler Bypass Position |
Using the Active Test function, switch the EGR cooler bypass valve between "Cooler" and "Bypass" a few times, and then check whether the Mass Air Flow Sensor value changes after switching the valve from "Cooler" to "Bypass".
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
When operating "Activate the VSV for EGR Cooler Bypass", check that "Cooler" and "Bypass" can be switched between and the EGR cooler by-pass valve regulating link operates. If the link does not operate, the inspection cannot be performed correctly. Therefore, inspect and repair the following parts, perform the Active Test and read the changes in the Mass Air Flow Sensor value.
- No. 2 EGR valve assembly
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
- Vacuum hose connection
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
- Vacuum switching valve assembly (for EGR Bypass Valve)
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>INSPECTION
| GTS Display | Result | Proceed to |
|---|---|---|
| Activate the VSV for EGR Cooler Bypass:
Cooler to Bypass |
Mass Air Flow Sensor value does not change | A |
| Mass Air Flow Sensor value changes | B |
If the EGR cooler is clogged, the Mass Air Flow Sensor value changes.
When confirming the change in the Mass Air Flow Sensor value, do not determine the change at "Half Pos". Perform the Active Test so that the system changes from "Cooler" to "Bypass" to confirm the change in the Mass Air Flow Sensor value.
A
B
Remove the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL
Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.
When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.
Do not forcibly open the valve, as it may be damaged or deformed.
When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.
When cleaning the electric EGR control valve assembly, care should be taken to prevent the ingress of cleaning solvent into the bearings of the valve shaft, and when wiping off deposits on the EGR valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR valve.
When cleaning the electric EGR control valve assembly, perform the initialization procedure.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION
If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.
If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the electric EGR control valve assembly.
Reinstall the electric EGR control valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the malfunctioning part in the intake system.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 1 EGR cooler.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR COOLER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.
Before replacing the mass air flow meter sub-assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off and wait for 30 seconds.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.
| Tester Display |
|---|
| Mass Air Flow Sensor |
Read the Mass Air Flow Sensor value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for EGR Cooler Bypass / Data List / Mass Air Flow Sensor and EGR Cooler Bypass Position.
Whether the EGR is passing through the bypass side or cooler side during the Active Test can be confirmed by checking EGR Cooler Bypass Position.
| Active Test Display |
|---|
| Activate the VSV for EGR Cooler Bypass |
| Data List Display |
|---|
| Mass Air Flow Sensor |
| EGR Cooler Bypass Position |
Using the Active Test function, switch the EGR cooler bypass valve between "Cooler" and "Bypass" a few times, and then check whether the Mass Air Flow Sensor value changes after switching the valve from "Cooler" to "Bypass".
If idling continues for 20 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.
When operating "Activate the VSV for EGR Cooler Bypass", check that "Cooler" and "Bypass" can be switched between and the EGR cooler by-pass valve regulating link operates. If the link does not operate, the inspection cannot be performed correctly. Therefore, inspect and repair the following parts, perform the Active Test and read the changes in the Mass Air Flow Sensor value.
- No. 2 EGR valve assembly
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
- Vacuum hose connection
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION
- Vacuum switching valve assembly (for EGR Bypass Valve)
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR BYPASS VALVE SWITCHING VALVE>INSPECTION
| GTS Display | Result | Proceed to |
|---|---|---|
| Activate the VSV for EGR Cooler Bypass:
Cooler to Bypass |
Mass Air Flow Sensor value does not change | A |
| Mass Air Flow Sensor value changes | B |
If the EGR cooler is clogged, the Mass Air Flow Sensor value changes.
When confirming the change in the Mass Air Flow Sensor value, do not determine the change at "Half Pos". Perform the Active Test so that the system changes from "Cooler" to "Bypass" to confirm the change in the Mass Air Flow Sensor value.
A
B
Remove the exhaust manifold converter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL
Visually check for catalyst clogging or carbon deposits adhering to the inner wall of the exhaust pipe upstream of the catalyst.
Less than 10% of the cells are clogged.
Reinstall the exhaust manifold converter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>INSTALLATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the lack of power (turbocharger system).
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
Replace the exhaust manifold converter sub-assembly.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL
Perform the initialization procedure for "Catalyst Deterioration Learning Value Clear" and "DPF Deposition Value Clear".
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 1 EGR cooler.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR COOLER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT