While the engine is being cranked, the ECM detects the starter signal (STA signal) and performs engine control when the engine starts.
If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) or more for more than 20 seconds.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P061512 | Starter Relay Circuit Short to Battery | Conditions (a), (b) and (c) are met for 20 seconds (1 trip detection logic):
(a) Vehicle speed is more than 20 km/h (12.4 mph). (b) Engine speed is more than 1000 rpm. (c) STA signal is on. |
·
STARTER relay ·
Park/Neutral position switch assembly*1 ·
Clutch start switch assembly*2 ·
STA signal circuit ·
ECM |
Comes on | DTC stored | SAE Code: P0617 |
*1: for Automatic transmission
*2: for Manual transmission
| DTC No. | Data List |
|---|---|
| P061512 | Starter SW |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P061512 | Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>INITIALIZATION).
The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>PROBLEM SYMPTOMS TABLE).
If this DTC is output, inspect the starter assembly.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Starter SW.
| Tester Display |
|---|
| Starter SW |
Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.
| Result | Proceed to | |
|---|---|---|
| Driving at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more | OFF | A |
| ON | B | |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Starter SW.
| Tester Display |
|---|
| Starter SW |
Remove the STARTER relay from the No. 1 engine room relay block and junction block assembly.
According to the display on the GTS, read the Data List.
| Result | Proceed to |
|---|---|
| The Data List item "Starter SW" does not change from ON. | A |
| The Data List item "Starter SW" changes from ON to OFF. | B |
When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the STARTER relay is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | STARTER Relay |
The purpose of this step is to check for STARTER relay terminal voltage under abnormal conditions.
Remove the STARTER relay from the No. 1 engine room relay block and junction block assembly.
Turn the ignition switch to ON.
Measure the voltage between STARTER relay terminal 2 and body ground.
Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the STARTER relay.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:
Short to +B in the circuit of a connected ECU or the switch.
Short to +B in the wire harness.
| Result | Proceed to |
|---|---|
| NEXT
(for Automatic Transmission Models) |
A |
| NEXT
(for Manual Transmission Models) |
B |
A
B
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | STARTER Relay |
Disconnect the park/neutral position switch assembly connector.
Measure the voltage between STARTER relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between STARTER relay terminal 2 and body ground does not change when the connector is disconnected. | A |
| The voltage between STARTER relay terminal 2 and body ground changes when the connector is disconnected. | B |
If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | STARTER Relay |
Disconnect the ECM connector.
Measure the voltage between STARTER relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between STARTER relay terminal 2 and body ground does not change when the connector is disconnected. | A |
| The voltage between STARTER relay terminal 2 and body ground changes when the connector is disconnected. | B |
If the voltage is the same before and after disconnecting the connector, the ECM is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
Repair or replace harness or connector (STA signal circuit).
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the park/neutral position switch assembly.
Click hereDrivetrain>AC60E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | STARTER Relay |
Disconnect the clutch start switch assembly connector.
Measure the voltage between STARTER relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between STARTER relay terminal 2 and body ground does not change when the connector is disconnected. | A |
| The voltage between STARTER relay terminal 2 and body ground changes when the connector is disconnected. | B |
If the voltage is the same before and after disconnecting the connector, the clutch start switch assembly is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | STARTER Relay |
Disconnect the ECM connector.
Measure the voltage between STARTER relay terminal 2 and body ground and compare it to the voltage measured in the previous step.
| Result | Proceed to |
|---|---|
| The voltage between STARTER relay terminal 2 and body ground does not change when the connector is disconnected. | A |
| The voltage between STARTER relay terminal 2 and body ground changes when the connector is disconnected. | B |
If the voltage is the same before and after disconnecting the connector, the ECM is normal.
DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.
A
B
Repair or replace harness or connector (STA signal circuit).
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the clutch start switch assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the STARTER relay.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT