When the ignition switch is turned to ON, battery power is supplied to the IGSW terminal of the ECM and MREL is operated.
As a result, the EFI MAIN Relay contact closes and power is supplied to the +B, +B2 and +B3 terminals of the ECM.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
| *a | Component with harness connected
(ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N2-4 (+B) - A2-5 (E1) | Ignition switch ON | 11 to 14 V |
| N2-3 (+B2) - A2-5 (E1) | Ignition switch ON | 11 to 14 V |
| N2-2 (+B3) - A2-5 (E1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>PROBLEM SYMPTOMS TABLE
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A2-5 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A2-18 (IGSW) - A2-5 (E1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the EFI MAIN relay.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Remove the EFI MAIN relay from the No. 1 engine room relay brock and junction brock assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N2-14 (MREL) - EFI MAIN relay terminal 2 | Always | Below 1 Ω |
| N2-4 (+B) - EFI MAIN relay terminal 5 | Always | Below 1 Ω |
| N2-3 (+B2) - EFI MAIN relay terminal 5 | Always | Below 1 Ω |
| N2-2 (+B3) - EFI MAIN relay terminal 5 | Always | Below 1 Ω |
| N2-14 (MREL) or EFI MAIN relay terminal 2 - Body ground and other terminals | Always | 10 kΩ or higher |
| N2-4 (+B) or EFI MAIN relay terminal 5 - Body ground and other terminals | Always | 10 kΩ or higher |
| N2-3 (+B2) or EFI MAIN relay terminal 5 - Body ground and other terminals | Always | 10 kΩ or higher |
| N2-2 (+B3) or EFI MAIN relay terminal 5 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *a | EFI MAIN Relay |
Remove the EFI MAIN relay from the No. 1 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI MAIN relay terminal 3 - Body ground | Always | 11 to 14 V |
| EFI MAIN relay terminal 1 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the No. 1 integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A2-18 (IGSW) - 1D-1 | Always | Below 1 Ω |
| 1E-4 - Body ground | Always | Below 1 Ω |
| A2-18 (IGSW) or 1D-1 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay (IG2 MAIN relay).
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | No. 1 Engine Room Relay Block and Junction Block Assembly without No. 1 Integration Relay |
Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 - Body ground | Always | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK (w/ Entry and Start System) | A |
| OK (w/o Entry and Start System) | B |
| NG | C |
A
B
C
Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N156-17 (IG1D) - 1D-2 | Always | Below 1 Ω |
| N156-17 (IG1D) or 1D-2 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>1GD-FTV (STARTING)>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG