The side airbag pressure sensor LH and side airbag pressure sensor RH detect impacts to the vehicle through changes in pressure inside the front doors caused by deformation of the outer side of the front doors and send signals to the airbag sensor assembly.
Based on the signals sent by the side airbag pressure sensor, the airbag sensor assembly determines if the SRS should be deployed.
If the difference between the pressure detected by the side airbag pressure sensor LH and the pressure detected by the side airbag pressure sensor RH exceeds a certain value a certain number of times, the airbag sensor assembly will output DTC B166A.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B166A | Pressure Sensor Difference for Front Door | The difference between the pressure detected by the side airbag pressure sensor LH and the side airbag pressure sensor RH exceeds a certain value a certain number of times. | ·
Side airbag pressure sensor LH ·
Side airbag pressure sensor RH ·
Airbag sensor assembly |
Comes on | Not applicable |
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>DTC CHECK / CLEAR
DTCs B166D, B166E, B167B and B167C are not output.
If B166D, B166E, B167B and B167C is output, perform troubleshooting for the DTC first.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the side airbag pressure sensor LH with a known good one.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
Perform the following inspection using known good parts from another vehicle if possible.
When using a new part, since the side airbag pressure sensor LH and RH have the same part number, prepare either one.
A prepared side airbag pressure sensor can also be used for the side airbag pressure sensor RH inspection.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B166A is output |
| DTC B166A is not output |
Codes other than DTC B166A may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Restore the side airbag pressure sensor LH that was installed for testing to its original location.
DTC B166A is output
DTC B166A is not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
Replace the side airbag pressure sensor RH with a known good one.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
Perform the following inspection using known good parts from another vehicle if possible.
Use the side airbag pressure sensor that was prepared during the side airbag pressure sensor LH inspection.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B166A is output |
| DTC B166A is not output |
Codes other than DTC B166A may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Restore the side airbag pressure sensor RH that was installed for testing to its original location.
DTC B166A is output
DTC B166A is not output
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL