Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P01009B  Mass or Volume Air Flow Sensor "A" High/Excessive Flow  P01009C  Mass or Volume Air Flow Sensor "A" Low/Insufficient Flow  


DESCRIPTION

Refer to DTC P010012.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P010012

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P01009B Mass or Volume Air Flow Sensor "A" High/Excessive Flow After the engine is completely warmed up, while the accelerator pedal is released for 7 seconds or more and the vehicle is decelerating, the intake air volume is higher than the threshold* (EGR valve fully closed and throttle valve is fully open) (2 trip detection logic).
*: The threshold is different depending on the values of "Engine Speed", "Intake Manifold Absolute Pressure" and "Intake Air Temperature B1S1 (Turbo)".
·

Mass air flow meter sub-assembly

·

Intake air temperature sensor (turbo)

·

Manifold absolute pressure sensor

·

Electric EGR control valve assembly

·

ECM

·

Open or short in mass air flow meter sub-assembly circuit


Comes on DTC stored SAE Code: P0101
P01009C Mass or Volume Air Flow Sensor "A" Low/Insufficient Flow After the engine is completely warmed up, while the accelerator pedal is released for 7 seconds or more and the vehicle is decelerating, the intake air volume is lower than the threshold* (EGR valve fully closed and throttle valve is fully open) (2 trip detection logic).
*: The threshold is different depending on the values of "Engine Speed", "Intake Manifold Absolute Pressure" and "Intake Air Temperature B1S1 (Turbo)".
·

Mass air flow meter sub-assembly

·

Intake air temperature sensor (turbo)

·

Manifold absolute pressure sensor

·

Electric EGR control valve assembly

·

ECM

·

Open or short in mass air flow meter sub-assembly circuit


Comes on DTC stored SAE Code: P0101

HINT:
·

P01009B (High air flow rate malfunction): For example when the vehicle is decelerating and "Mass Air Flow Sensor" is 52 gm/sec or more, a high air flow malfunction is confirmed (at "Engine Speed" is 1600 rpm, "Intake Manifold Absolute Pressure" is 110 kPa and "Intake Air Temperature B1S1 (Turbo)" is 35°C).

·

P01009C (Low air flow rate malfunction): For example, when the vehicle is decelerating and "Mass Air Flow Sensor" is 29 gm/sec or less, a low air flow malfunction is confirmed (at "Engine Speed" is 1600 rpm, "Intake Manifold Absolute Pressure" is 110 kPa and "Intake Air Temperature B1S1 (Turbo)" is 35°C).



Related Data List
DTC No. Data List
P01009B
P01009C
·

Mass Air Flow Sensor

·

Intake Manifold Absolute Pressure

·

Engine Speed

·

Intake Air Temperature B1S1 (Turbo)

·

Target EGR Valve Position No.1

·

Actual EGR Valve Position No.1

·

EGR Close Learning Value Bank 1



HINT:

If DTC P01009B and/or P01009C is stored, either of the following symptoms may appear:

1.

As the ECU mistakenly determines that there is less air than the actual intake air amount, EGR is decreased to match the target EGR.

-

Combustion noise worsens


2.

As the ECU mistakenly determines that there is more air than the actual intake air amount, EGR is increased to match the target EGR:

-

Misfire

-

White smoke

-

Black smoke




CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P01009B
P01009C
After the engine is completely warmed up, perform the following procedure 3 times: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
After performing the above procedure, immediately stop the vehicle and confirm that "Exhaust Temperature B1S2" displays 300°C (572°F) or higher using the GTS.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P01009B OR P01009C)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
DTC P01009B or P01009C is output A
DTC P01009B or P01009C and other DTCs are output B


HINT:

If codes other than DTC P01009B or P01009C are output, perform troubleshooting for those DTCs first.




A

2.CHECK FREEZE FRAME DATA (MASS AIR FLOW SENSOR AND ENGINE SPEED)

B

2.CHECK FREEZE FRAME DATA (MASS AIR FLOW SENSOR AND ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Check the freeze frame data.

Result:
Result Proceed to
·

Engine speed: 1350 rpm or less

·

Mass Air Flow Sensor: 246.0 gm/sec or more


A
·

Engine speed: 1350 rpm or more

·

Mass Air Flow Sensor: 0.03 gm/sec or less


Except above B




A

3.READ VALUE USING GTS (ENGINE SPEED AND MASS AIR FLOW SENSOR)

B

8.READ VALUE USING GTS (ENGINE SPEED AND MASS AIR FLOW SENSOR)
3.READ VALUE USING GTS (ENGINE SPEED AND MASS AIR FLOW SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
50003 372 211,215

d.

Start the engine and read the value when 30 seconds has elapsed.

Standard:
Engine Speed Mass Air Flow Sensor
Idling
·

0.5 to 15 gm/sec (EGR on)

·

10 to 22 gm/sec (EGR off)


3000 rpm (without load)
·

42 to 89 gm/sec (EGR on)

·

72 to 117 gm/sec (EGR off)





Result:
Proceed to
OK
NG



OK

4.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
4.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the GTS to the DLC3.


h.

Enter the following menus: Powertrain / Engine / Data List / Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 372 1134
HINT:
·

"Exhaust Temperature B1S2" must be 300°C or more.

·

If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.




i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P01009B or P01009C.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC DTC P01009B or P01009C is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.





A

END

B

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E20-1 (FG) - E6-31 (VG) Always Below 1 Ω
E20-2 (E2G) - E6-29 (EVG) Always Below 1 Ω
E20-1 (FG) or E6-31 (VG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

19.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.READ VALUE USING GTS (ENGINE SPEED AND MASS AIR FLOW SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Mass Air Flow Sensor
50003 372 211,215

d.

Start the engine and read the value when 30 seconds has elapsed.

Standard:
Engine Speed Mass Air Flow Sensor
Idling
·

0.5 to 15 gm/sec (EGR on)

·

10 to 22 gm/sec (EGR off)


3000 rpm (without load)
·

42 to 89 gm/sec (EGR on)

·

72 to 117 gm/sec (EGR off)





Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (ATMOSPHERIC PRESSURE AND INTAKE MANIFOLD ABSOLUTE PRESSURE)

NG

13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
9.READ VALUE USING GTS (ATMOSPHERIC PRESSURE AND INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Atmospheric Pressure and Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List
Tester Display
Atmospheric Pressure
Intake Manifold Absolute Pressure
50003 372 229,385

d.

Compare the values when the ignition switch is ON.

Standard:

Difference between "Intake Manifold Absolute Pressure" and "Atmospheric Pressure" is less than 8 kPa.


HINT:
·

If "Intake Manifold Absolute Pressure" and "Atmospheric pressure" have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather.




Result:
Proceed to
OK
NG



OK

10.CHECK INTAKE SYSTEM

NG

26.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
10.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leakage.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leakage from intake system.


HINT:
·

Check for abnormal disconnection, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

Air leaks from the intake system can be checked by applying soapy water and revving the engine.

·

Check for any modifications in the intake system made by the user.




Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (INTAKE AIR TEMPERATURE B1S1 AND INTAKE AIR TEMPERATURE B1S1 (TURBO))

NG

25.REPAIR OR REPLACE INTAKE SYSTEM
11.READ VALUE USING GTS (INTAKE AIR TEMPERATURE B1S1 AND INTAKE AIR TEMPERATURE B1S1 (TURBO))
a.

Connect the GTS to the DLC3.


b.

Soak the engine for a long time.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Intake Air Temperature B1S1 and Intake Air Temperature B1S1 (Turbo)

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature B1S1 (Turbo)
Intake Air Temperature B1S1
50003 372 310,613
OK:

Intake Air Temperature B1S1 is the same as Intake Air Temperature B1S1 (Turbo).



Result:
Proceed to
OK
NG



OK

12.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

23.INSPECT INTAKE AIR TEMPERATURE SENSOR (TURBO)
12.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position Bank 1 / Data List / Actual EGR Valve Position No.1.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position Bank 1
Data List Display
Actual EGR Valve Position No.1
50004 372 70 382

d.

When changing the Active Test value consecutively to 1, 30, 60, 90, 60, 30 and 1%, check that Actual EGR Valve Position No.1 smoothly changes to the set opening angle.

OK:

Value smoothly changes to set opening angle.



e.

Enter the following menus: Powertrain / Engine / Data List / EGR Close Learning Value Bank 1.

Powertrain > Engine > Data List
Tester Display
EGR Close Learning Value Bank 1
50003 372 969

f.

Read the values.

Standard:

0 to 1 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

16.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
13.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E20-1 (FG) - E6-31 (VG) Always Below 1 Ω
E20-2 (E2G) - E6-29 (EVG) Always Below 1 Ω
E20-1 (FG) or E6-31 (VG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

19.REPAIR OR REPLACE HARNESS OR CONNECTOR
14.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
15.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the GTS to the DLC3.


h.

Enter the following menus: Powertrain / Engine / Data List / Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 372 1134
HINT:
·

"Exhaust Temperature B1S2" must be 300°C or more.

·

If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.




i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P01009B or P01009C.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC DTC P01009B or P01009C is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.





A

END

B

21.REPLACE ECM
16.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Remove the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL


b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

NOTICE:
·

When cleaning the electric EGR control valve assembly, make sure the valve is completely closed.

·

Do not forcibly open the valve, as it may be damaged or deformed.

·

When cleaning the electric EGR control valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.

·

When cleaning the EGR control valve, care should be taken to prevent the ingress of cleaning solvent into the bearings of the valve shaft, and when wiping off deposits on the EGR valve, care should be taken not to push the deposits into the bearings of the valve shaft. These contaminants may adversely affect the function of the EGR valve.

·

When cleaning the electric EGR control valve assembly, perform initialization procedure.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>INITIALIZATION




c.
A346511C01
0.865,2.458 1.115,2.708 0.25,0.25 2.115,4.344 2.26,4.344 2.26,4.344 2.604,3.854 true 2.594,3.229 2.75,2.531 2.75,2.531 2.885,2.531 true 0.667,3.469 0.688,2.583 0.688,2.583 0.792,2.583 true 0.938,2.49 1.094,2.688 0.156,0.198 10 false A 2.948,2.469 3.208,2.708 0.26,0.24 10 false *1 1.969,4.281 2.26,4.5 0.292,0.219 10 false *1 0.844,4.198 1.135,4.417 0.292,0.219 10 false *a 2.604,4.188 2.896,4.406 0.292,0.219 10 false *b
*1 Gap
*a OK
*b NG


Hold the electric EGR control valve assembly up to a light, and then from the side indicated by the arrow in the illustration, visually check that there is no gap between the valve and body.

OK:

No light passes through (there is no gap between the valve and body).


HINT:

Light passes through part A shown in the illustration even if the valve is completely closed as there is an opening in the seal ring of the valve. This is not a problem.


If light passes through (there is a gap between the valve and body), replace the electric EGR control valve assembly.


Result:
Proceed to
OK
NG



OK

17.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

22.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
17.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter sub-assembly, the output characteristics of the mass air flow meter sub-assembly may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

18.CHECK DTC OUTPUT
18.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the GTS to the DLC3.


h.

Enter the following menus: Powertrain / Engine / Data List / Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 372 1134
HINT:
·

"Exhaust Temperature B1S2" must be 300°C or more.

·

If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.




i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P01009B or P01009C.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC DTC P01009B or P01009C is output B
All Readiness NORMAL A
ABNORMAL B


HINT:

If STATUS is INCOMPLETE, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.





A

END

B

21.REPLACE ECM
19.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.


f.

Stop the vehicle immediately after completing the above procedure.


g.

Connect the GTS to the DLC3.


h.

Enter the following menus: Powertrain / Engine / Data List / Exhaust Temperature B1S2.

Powertrain > Engine > Data List
Tester Display
Exhaust Temperature B1S2
50003 372 1134
HINT:
·

"Exhaust Temperature B1S2" must be 300°C or more.

·

If "Exhaust Temperature B1S2" is less than 300°C (572°F), perform the DTC detection drive pattern again, increasing the vehicle speed so that the exhaust gas temperature increases.




i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

Confirm that the pending DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

21.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
22.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL


Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
23.INSPECT INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Inspect the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

17.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

24.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
24.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)
a.

Replace the intake air temperature sensor (turbo).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
25.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the intake system.


Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
26.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED