The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the EGR valve removal/installation are shown below.
| Replacement Part or Procedure | Necessary Procedures | Effects/Inoperative when not Performed | Link |
|---|---|---|---|
·
Replacement of diesel throttle body assembly ·
Replacement of electric EGR control valve assembly |
Perform initialization | - |
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
1.DRAIN ENGINE COOLANT (for Air Cooled Type Intercooler)
85110
2.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
55701J
3.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
17940D
4.REMOVE INTERCOOLER ASSEMBLY (for Water Cooled Type Intercooler)
26100G
5.REMOVE DIESEL THROTTLE BODY ASSEMBLY
87209
6.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Heater)
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
for Air Cooled Type Intercooler:
w/ Rear Heater:
Slide the 2 clamps and disconnect the 2 water hose sub-assemblies from the water pipe.
Slide the 4 clamps and remove the 2 water hose sub-assemblies from the air conditioning unit assembly and No. 2 water by-pass pipe.
w/o Rear Heater:
Slide the 4 clamps and remove the 2 water hose sub-assemblies from the air conditioning unit assembly and No. 2 water by-pass pipe.
for Water Cooled Type Intercooler:
Slide the 4 clamps and remove the 2 water hose sub-assemblies from the air conditioning unit assembly and water pipe.
16278
7.REMOVE NO. 2 WATER BY-PASS PIPE (for Air Cooled Type Intercooler)
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
| *A | w/ Heater |
| *B | w/o Heater |
for Laminated EGR Pre-cooler:
Detach the clamp, slide the clamp and disconnect the No. 18 water by-pass hose from the EGR pipe with cooler sub-assembly.
| *A | w/ Heater |
| *B | w/o Heater |
w/ Viscous Heater:
Slide the clamp and disconnect the water by-pass hose sub-assembly from the No. 2 water by-pass pipe.
w/ Heater:
Slide the clamp and disconnect the No. 13 water by-pass hose from the No. 2 water by-pass pipe.
Slide the clamp and disconnect the No. 15 water by-pass hose from the water by-pass pipe.
Slide the clamp and disconnect the No. 16 water by-pass hose from the No. 1 EGR cooler.
| *A | w/ Heater |
| *B | w/o Heater |
Remove the 3 bolts and No. 2 water by-pass pipe from the cylinder head cover sub-assembly and No. 3 water by-pass pipe sub-assembly.
89421C
8.REMOVE DIESEL TURBO PRESSURE SENSOR
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Disconnect the connector from the diesel turbo pressure sensor.
Disconnect the vacuum hose and remove the bolt and turbo pressure sensor from the No. 3 water by-pass pipe sub-assembly.
23265C
9.REMOVE GAS FILTER
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Disconnect the vacuum hose from the intake manifold.
Detach the clamp and remove the gas filter from the gas filter bracket.
12632
10.REMOVE NO. 2 ENGINE COVER BRACKET (for Air Cooled Type Intercooler)
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the 2 bolts and No. 2 engine cover bracket from the No. 3 water by-pass pipe sub-assembly and No. 2 EGR valve assembly.
23941
11.DISCONNECT NO. 1 FUEL FILTER PROTECTOR
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Disconnect the connector from the fuel filter assembly.
Detach the clamp and disconnect the wire harness from the No. 1 fuel filter protector.
Remove the bolt and disconnect the No. 1 fuel filter protector from the body.
82121
12.DISCONNECT ENGINE WIRE
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
for Air Cooled Type Intercooler:
Disconnect the 2 connectors from the turbocharger sub-assembly.
Detach the clamp and disconnect the connector from the intake mass air flow meter sub-assembly.
Disconnect the connector from the camshaft position sensor.
w/ DPF:
Disconnect the connector from the exhaust fuel addition injector assembly.
Detach the 3 clamps and disconnect the engine wire from the 2 wire harness clamp brackets.
w/ DPF:
Detach the clamp and disconnect the connector from the differential pressure sensor.
Disconnect the 3 connectors from the exhaust gas temperature sensors.
Disconnect the 4 connectors from the 4 injector assemblies.
Disconnect the connector from the electric EGR control valve assembly.
Disconnect the connector from the glow plug connector.
Remove the bolt and disconnect the connector from the sensor wire of the common rail assembly.
Disconnect the 2 connectors from the vane pump assembly.
Detach the 2 clamps and disconnect the engine wire from the No. 3 water by-pass pipe sub-assembly and wire harness clamp bracket.
Detach the clamp, remove the bolt and disconnect the engine wire from the No. 4 water by-pass pipe sub-assembly.
for Water Cooled Type Intercooler:
Detach the clamp and disconnect the 2 connectors from the turbocharger sub-assembly.
Detach the clamp and disconnect the connector from the intake mass air flow meter sub-assembly.
Disconnect the connector from the camshaft position sensor.
Disconnect the connector from the exhaust fuel addition injector assembly.
Detach the 2 clamps and disconnect the engine wire from the wire harness clamp bracket.
Detach the clamp, remove the 2 bolts and disconnect the engine wire from the intercooler support bracket.
Disconnect the connector from the differential pressure sensor.
Disconnect the 3 connectors from the exhaust gas temperature sensors.
Disconnect the 4 connectors from the 4 injector assemblies.
Disconnect the connector from the connecting wire.
Disconnect the connector from the glow plug connector.
Disconnect the connector from the electric EGR control valve assembly.
Detach the clamp, remove the 2 bolts and disconnect the engine wire from the cylinder head cover sub-assembly and No. 3 water by-pass pipe sub-assembly.
Disconnect the connector from the connecting wire.
Disconnect the 2 connectors from the vane pump assembly.
Detach the clamp, remove the bolt and disconnect the engine wire from the No. 3 water by-pass pipe sub-assembly and oil level gage guide sub-assembly.
Detach the clamp, remove the bolt and disconnect the engine wire from the No. 4 water by-pass pipe sub-assembly.
25804
13.REMOVE VACUUM CONTROL VALVE SET
25625
14.REMOVE EGR VALVE BRACKET
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the bolt, nut and EGR valve bracket from the electric EGR control valve assembly and intake manifold.
89425D
15.REMOVE NO. 5 EXHAUST GAS TEMPERATURE SENSOR (w/ Exhaust Gas Temperature Sensor for EGR)
25612
16.REMOVE NO. 2 EGR PIPE
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
| *A | w/o Exhaust Gas Temperature Sensor for EGR |
| *B | w/ Exhaust Gas Temperature Sensor for EGR |
Remove the bolt, 4 nuts and No. 2 EGR pipe from the electric EGR control valve assembly and intake manifold.
Remove the 2 gaskets.
25800
17.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Detach the clamp and disconnect the connector from the common rail assembly.
Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.
Remove the 2 bolts and electric EGR control valve assembly.
Remove the gasket.
16206B
18.REMOVE NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
for Air Cooled Type Intercooler:
Detach the clamp and disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.
Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.
Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the No. 1 EGR cooler.
for Water Cooled Type Intercooler:
Detach the clamp and disconnect the No. 4 fuel hose from the No. 3 water by-pass pipe sub-assembly.
Slide the clamp and disconnect the No. 8 water by-pass hose from the No. 3 water by-pass pipe sub-assembly.
Remove the 2 bolts and No. 3 water by-pass pipe sub-assembly from the No. 1 EGR cooler.
16209
19.DISCONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
for Air Cooled Type Intercooler:
| *1 | No. 7 Water By-pass Hose |
| *2 | Water Hose |
Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 1 EGR cooler.
Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.
Remove the 2 bolts and disconnect the No. 4 water by-pass pipe sub-assembly from the intake manifold.
for Water Cooled Type Intercooler:
| *1 | No. 17 Water By-pass Hose |
| *2 | No. 7 Water By-pass Hose |
| *3 | Water Hose |
Slide the clamp and disconnect the No. 17 water by-pass hose from the No. 1 EGR pipe sub-assembly.
Slide the clamp and disconnect the No. 7 water by-pass hose from the No. 1 EGR cooler.
Slide the clamp and disconnect the water hose from the No. 2 EGR valve assembly.
Remove the 2 bolts and disconnect the No. 4 water by-pass pipe sub-assembly from the intake manifold.
25601
20.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (for Single Actuator EGR Bypass Valve)
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
for Air Cooled Type Intercooler:
Remove the bolt and disconnect the No. 1 EGR pipe sub-assembly from the vacuum transmitting pipe sub-assembly.
Remove the 4 nuts and No. 1 EGR pipe sub-assembly from the exhaust manifold and EGR valve adapter.
Remove the 2 gaskets.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.
for Water Cooled Type Intercooler:
Remove the bolt and disconnect the No. 1 EGR pipe sub-assembly from the vacuum transmitting pipe sub-assembly.
Remove the 4 nuts and No. 1 EGR pipe sub-assembly from the exhaust manifold and EGR valve adapter.
Remove the 2 gaskets.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.
25601
21.DISCONNECT EGR PIPE WITH COOLER SUB-ASSEMBLY (for Double Actuator EGR Bypass Valve)
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
Remove the bolt and disconnect the EGR pipe with cooler sub-assembly from the cylinder head sub-assembly.
Remove the 4 nuts and disconnect the EGR pipe with cooler sub-assembly from the exhaust manifold and EGR valve adapter.
Remove the 2 gaskets.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold.
22.REMOVE NO. 1 EGR COOLER WITH NO. 2 EGR VALVE ASSEMBLY
To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
| *A | for Single Actuator EGR Bypass Valve |
| *B | for Double Actuator EGR Bypass Valve |
for Air Cooled Type Intercooler:
Remove the 4 bolts and No. 1 EGR cooler with No. 2 EGR valve assembly from the intake manifold.
for Water Cooled Type Intercooler:
Remove the 4 bolts, No. 1 EGR cooler with No. 2 EGR valve assembly and No. 2 intercooler support bracket from the intake manifold.
25624
23.REMOVE EGR VALVE ADAPTER
Remove the 2 bolts and EGR valve adapter from the No. 2 EGR valve assembly.
Remove the gasket.
25630
24.REMOVE NO. 2 EGR VALVE ASSEMBLY
| *A | for Single Actuator EGR Bypass Valve |
| *B | for Double Actuator EGR Bypass Valve |
Remove the 4 bolts and No. 2 EGR valve assembly from the No. 1 EGR cooler.
Remove the gasket.
Using an E8 "TORX" socket wrench, remove the 4 stud bolts from the No. 2 EGR valve assembly.