Refer to DTC P202A12.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P205A11 | Reductant Tank Temperature Sensor Circuit Low Circuit Short to Ground | An open or short circuit occurs in the temperature sensor circuit for 10 seconds or more (1 trip detection logic). | ·
Open or short in temperature sensor circuit ·
Temperature sensor (urea pump) ·
Urea pump control ECU |
Comes on | DTC stored | SAE Code: P205C |
| P205A15 | Reductant Tank Temperature Sensor Circuit High Circuit Short to Battery or Open | An open or short circuit occurs in the temperature sensor circuit for 10 seconds or more (1 trip detection logic). | ·
Open or short in temperature sensor circuit ·
Temperature sensor (urea pump) ·
Urea pump control ECU |
Comes on | DTC stored | SAE Code: P205D |
| DTC No. | Data List |
|---|---|
| P205A11
P205A15 |
Reductant Temperature |
The urea pump control ECU calculates the temperature of the urea solution based on the output voltage of the temperature sensor. When the temperature sensor output voltage is outside the normal range, there may be a malfunction, short or open circuit in the temperature sensor. In this case, the urea pump control ECU determines that there is a malfunction in the temperature sensor, and then illuminates the MIL and stores a DTC through the ECM.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P205A11
P205A15 |
Ignition switch to ON and wait for 10 seconds or more. |
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Temperature.
| Tester Display |
|---|
| Reductant Temperature |
Read the values.
Reductant temperature is the same as the ambient temperature of urea tank assembly.
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 80°C (176°F) | B |
When the GTS indicates -40°C (-40°F), there is an open circuit.
When the GTS indicates 80°C (176°F), there is a short circuit.
A
B
Disconnect the urea pump connector.
| *1 | Temperature Sensor (Urea Pump) | *2 | Urea Pump Control ECU |
| *a | Front view of wire harness connector
(to Urea Pump) |
- | - |
Connect terminals 1 (TUW) and 2 (ETUW) of the urea pump connector on the wire harness side.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Temperature.
| Tester Display |
|---|
| Reductant Temperature |
Read the values.
80°C (176°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the urea pump.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for 30 seconds or more.
Turn the ignition switch to ON and wait for 10 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTCs are not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the urea pump connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X4-1 (TUW) - N37-54 (THU) | Always | Below 1 Ω |
| X4-2 (ETUW) - N37-53 (ETHU) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the urea pump control ECU.
Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Temperature Sensor (Urea Pump) |
| *2 | Urea Pump Control ECU |
Disconnect the urea pump connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Diesel Exhaust / Reductant Temperature.
| Tester Display |
|---|
| Reductant Temperature |
Read the values.
-40°C (-40°F)
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the urea pump connector.
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| X4-1 (TUW) and N37-54 (THU) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG