Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P208A14  Reductant Pump "A" Control Circuit Low Circuit Short to Ground or Open  P208A19  Reductant Pump "A" Control Circuit High Circuit Current Above Threshold  P208A96  Reductant Pump "A" Control Performance/Stuck Off Component Internal Failure  P20E900  Reductant Pressure Too High  


DESCRIPTION

The urea pump is a bottom entry type intake pump installed to the bottom of the urea tank sub-assembly.

This urea pump has functions that 1) pressurize and supply the urea solution, 2) thaw frozen urea solution and heat the urea solution to prevent further freezing, 3) gauge the level of remaining urea solution inside the tank and 4) filter foreign matter inside the urea tank sub-assembly.

When the engine is stopped, the urea pump operates in reverse to draw the urea solution in the pipe back into the urea tank sub-assembly.

The urea pump performs feedback control using the pressure sensor, achieving accurate urea solution volume adjustment control.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P208A14 Reductant Pump "A" Control Circuit Low Circuit Short to Ground or Open When the urea pump motor is operating, an open or short circuit occurs in the urea pump motor circuit (1 trip detection logic).
·

Open or short in urea tube with pump motor circuit

·

Urea pump

·

Urea pump control ECU


Comes on DTC stored SAE Code: P208C
P208A19 Reductant Pump "A" Control Circuit High Circuit Current Above Threshold When power is supplied to the urea pump (during normal/reverse operation, power supplied to heater, position fixed), the pump current is equal to or greater than a fixed value (1 trip detection logic). Urea pump Comes on DTC stored SAE Code: P208D
P208A96 Reductant Pump "A" Control Performance/Stuck Off Component Internal Failure When each pump status is "operating" (operation check, filling, pressure increase, pressure maintenance, line pressure relief), urea pump rotation malfunctions, pressure malfunctions, etc., are detected multiple times (1 trip detection logic). Urea pump Comes on DTC stored SAE Code: P208B
P20E900 Reductant Pressure Too High After filling the urea injector with urea solution from the urea pipe, the urea pressure is continuously higher than a fixed value (1 trip detection logic). Urea pump Comes on DTC stored SAE Code: P20E9

Related Data List
DTC No. Data List
P208A14 Reductant Pump Speed
P208A19
P208A96
P20E900
Reductant Pressure

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P208A14
P208A19
P208A96
P20E900
Idle engine for 5 second

WIRING DIAGRAM

A444448E01
0.135,3.021 3.5,3.219 3.365,0.198 10 false Pump Motor (Urea Pump) 3.5,0.292 3.656,0.49 0.156,0.198 10 false * 3.208,2.917 6.573,3.115 3.365,0.198 10 false *: Shielded 5.469,3.052 7.156,3.396 1.688,0.344 10 false Urea Pump Control ECU 5.844,0.708 6.458,0.906 0.615,0.198 10 false UPMU 0.906,0.708 1.521,0.906 0.615,0.198 10 false PHAA 0.906,1.281 1.521,1.479 0.615,0.198 10 false PHAB 5.844,1.292 6.458,1.49 0.615,0.198 10 false UPMV 5.844,1.865 6.458,2.063 0.615,0.198 10 false UPMW 5.844,2.438 6.458,2.635 0.615,0.198 10 false MSG 0.906,2.427 1.521,2.625 0.615,0.198 10 false MGND 0.906,1.865 1.521,2.063 0.615,0.198 10 false PHAC 0.156,2.854 0.469,3.052 0.313,0.198 10 false X4 5.469,2.896 5.781,3.094 0.313,0.198 10 false N37 1.458,1.156 1.615,1.354 0.156,0.198 10 false 8 1.448,0.604 1.604,0.802 0.156,0.198 10 false 7 5.531,2.302 6.167,2.51 0.635,0.208 10 false 23 1.438,1.74 1.771,1.917 0.333,0.177 10 false 16 1.438,2.302 2.146,2.552 0.708,0.25 10 false 15 5.521,1.74 6.229,1.99 0.708,0.25 10 false 33 5.521,1.156 6.24,1.427 0.719,0.271 10 false 22 5.563,0.594 5.719,0.792 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P208A14, P208A19, P208A96 OR P20E900)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
DTC P208A14 is output A
DTC P208A19, P208A96 or P20E900 is output B
DTC P208A19, P208A96 or P20E900 and other DTCs are output* C


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.




A

2.CHECK HARNESS AND CONNECTOR (PUMP MOTOR - UREA PUMP CONTROL ECU)

B

4.CHECK AROUND BOTTOM OF VEHICLE

C

2.CHECK HARNESS AND CONNECTOR (PUMP MOTOR - UREA PUMP CONTROL ECU)
a.

Disconnect the urea pump connector.


b.

Disconnect the urea pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X4-7 (PHAA) - N37-3 (UPMU) Always Below 1 Ω
X4-8 (PHAB) - N37-22 (UPMV) Always Below 1 Ω
X4-16 (PHAC) - N37-33 (UPMW) Always Below 1 Ω
X4-15 (MGND) - N37-23 (MSG) Always Below 1 Ω
X4-7 (PHAA) or N37-3 (UPMU) - Body ground and other terminals Always 10 kΩ or higher
X4-8 (PHAB) or N37-22 (UPMV) - Body ground and other terminals Always 10 kΩ or higher
X4-16 (PHAC) or N37-33 (UPMW) - Body ground and other terminals Always 10 kΩ or higher
X4-15 (MGND) or N37-23 (MSG) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AROUND BOTTOM OF VEHICLE

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

4.CHECK AROUND BOTTOM OF VEHICLE
4.CHECK AROUND BOTTOM OF VEHICLE
a.

Check around the bottom of the vehicle.

HINT:

If the urea solution dries on an object, deposition occurs and leaves behind a white powder.


Area to check:

·

Areas connecting the urea pump and urea injector set.

·

Perforations in the urea tank sub-assembly.

·

Connectors not connected properly.

·

Clogging of the cooling fins of the urea injector set.

HINT:

If the cooling fins are clogged with foreign matter, remove the foreign matter and clean the cooling fins.




b.

Repair any trouble areas.


Result:
Proceed to
NEXT



NEXT

5.PERFORM ACTIVE TEST USING GTS (ACTIVATES THE REDUCTANT PUMP CHECK)
5.PERFORM ACTIVE TEST USING GTS (ACTIVATES THE REDUCTANT PUMP CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and idle it for 5 seconds or more.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pump Check (Backward).

Powertrain > Engine > Active Test
Tester Display
Reductant Pump Check (Backward)
50004 372 85

h.

Perform the Active Test.


i.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Purge.

Powertrain > Engine > Active Test
Tester Display
Reductant Purge
50004 372 86

j.

Perform the Active Test.

HINT:

Perform the urea solution forced purge to draw the urea solution back into the urea tank sub-assembly from the urea injector set.



k.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

l.

Read the DTCs.


Result:
Result Proceed to
No DTCs are output A
DTC P208A19, P208A96 or P20E900 is output B
DTC P208A14 is output C



A

6.PERFORM ACTIVE TEST USING GTS (Activates the Reductant Filling (Pressure Keep))

B

7.REPLACE UREA PUMP

C

9.REPLACE UREA PUMP
6.PERFORM ACTIVE TEST USING GTS (Activates the Reductant Filling (Pressure Keep))
a.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Filling (Pressure Keep) / Data List / Diesel Exhaust / Reductant Pressure.

Powertrain > Engine > Active Test
Active Test Display
Reductant Filling (Pressure Keep)
Data List Display
Reductant Pressure
50004 372 84 1030

b.

Execute "Reductant Filling (Pressure Keep)


c.

Check the Reductant Pressure.

OK:

400 to 600 kPa


HINT:

During a malfunction, pressure either does not increase, or increases to 800 kPa or higher and then stops.



Result:
Proceed to
OK
NG



OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

7.REPLACE UREA PUMP
7.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and idle it for 5 seconds or more.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Start the engine and idle it for 5 seconds or more.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

i.

Confirm that the DTCs are not output again.


Result:
Proceed to
NEXT



NEXT

END

9.REPLACE UREA PUMP

Result:
Proceed to
NEXT



NEXT

10.PERFORM ACTIVE TEST USING GTS (ACTIVATES THE REDUCTANT PUMP CHECK)
10.PERFORM ACTIVE TEST USING GTS (ACTIVATES THE REDUCTANT PUMP CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and idle it for 5 seconds or more.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off for 30 seconds or more.


f.

Turn the ignition switch to ON and turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Pump Check (Backward).

Powertrain > Engine > Active Test
Tester Display
Reductant Pump Check (Backward)
50004 372 85

h.

Perform the Active Test.


i.

Enter the following menus: Powertrain / Engine / Active Test / Reductant Purge.

Powertrain > Engine > Active Test
Tester Display
Reductant Purge
50004 372 86

j.

Perform the Active Test.

HINT:

Perform the urea solution forced purge to draw the urea solution back into the urea tank sub-assembly from the urea injector set.



k.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

l.

Read the DTCs.


Result:
Result Proceed to
No DTCs are output A
DTC P208A14 is output B



A

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

B

11.REPLACE UREA PUMP CONTROL ECU
11.REPLACE UREA PUMP CONTROL ECU

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED