Refer to DTC P200873.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P200812 | Intake Manifold Runner Control Bank 1 Circuit Short to Battery | Short in vacuum switching valve assembly (for swirl control valve) circuit for 3 seconds (2 trip detection logic). | ·
Vacuum switching valve assembly (for swirl control valve) ·
Short in vacuum switching valve assembly (for swirl control valve) circuit ·
ECM |
Comes on | DTC stored | SAE Code: P2010 |
| P200814 | Intake Manifold Runner Control Bank 1 Circuit Short to Ground or Open | Open in vacuum switching valve assembly (for swirl control valve) circuit for 3 seconds (2 trip detection logic). | ·
Vacuum switching valve assembly (for swirl control valve) ·
Open in vacuum switching valve assembly (for swirl control valve) circuit ·
ECM |
Comes on | DTC stored | SAE Code: P2009 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P200812
P200814 |
2 seconds after engine is started, race engine for 1 second |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Disconnect the vacuum hoses from the vacuum switching valve assembly (for swirl control valve).
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.
| Tester Display |
|---|
| Activate the VSV for Swirl Control Valve |
Check the VSV operation when it is operated using the intelligent tester.
| Tester Operation | Specified Condition |
|---|---|
| VSV ON | Air from port E flows out through port F |
| VSV OFF | Air from port E flows out through air filter |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the vacuum switching valve assembly (for swirl control valve).
Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the vacuum switching valve assembly (for swirl control valve) connector.
| *a | Front view of wire harness connector
(to Vacuum Switching Valve Assembly (for Swirl Control Valve)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| E87-2 (SCV+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the vacuum switching valve assembly (for swirl control valve) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E87-1 (SCV-) - E5-10 (SCV) | Always | Below 1 Ω |
| E87-1 (SCV-) or E5-10 (SCV) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Remove the EFI MAIN relay from the No. 1 engine room relay block and junction block assembly.
Disconnect the vacuum switching valve assembly (for swirl control valve) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI MAIN relay terminal 5 - E87-2 (SCV+) | Always | Below 1 Ω |
| EFI MAIN relay terminal 5 or E87-2 (SCV+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the ECM power source circuit.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Start the engine and wait for 2 seconds or more.
Race the engine for 1 second or more.
Enter the following menus: Powertrain / Engine / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the vacuum switching valve assembly (for swirl control valve).
Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT