Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P200873  Intake Manifold Runner Control Bank 1 Actuator Stuck Closed  


DESCRIPTION

The swirl control valve is mounted on the intake manifold. The vacuum switching valve assembly is used to change the vacuum to control the swirl control valve.

The ECM determines the opening angle of the swirl control valve, and uses the vacuum switching valve assembly (for swirl control valve) to change the vacuum applied to the actuator's diaphragm to open and close the swirl control valve.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P200873 Intake Manifold Runner Control Bank 1 Actuator Stuck Closed When actual intake air volume detected by mass air flow meter continues to be smaller than volume estimated from boost pressure and intake air temperature sensor, ECM determines that swirl control valve is stuck closed (1 trip detection logic).
·

Vacuum switching valve assembly (for swirl control valve)

·

Open or short in vacuum switching valve assembly (for swirl control valve) circuit

·

Intake manifold (swirl control valve)

·

Electric EGR control valve assembly

·

Turbocharger sub-assembly

·

Mass air flow meter sub-assembly

·

Air cleaner hose

·

Vacuum hose

·

Air cleaner filter element is clogged

·

Intake hose is disconnected

·

ECM


Comes on DTC stored SAE Code: P2006

A357985C01
3.74,2.531 3.417,1.823 3.417,1.823 3.313,1.823 true 5.438,2.708 5.646,2.042 5.646,2.042 5.76,2.042 true 3.99,2.844 4.302,3.635 4.302,3.635 4.417,3.635 true 4.573,2.844 4.885,3.635 4.885,3.635 5,3.635 true 2.063,0.344 2.375,0.5 0.313,0.156 10 false *1 3.146,1.74 3.458,1.896 0.313,0.156 10 false *2 5.792,1.979 6.104,2.135 0.313,0.156 10 false *3 5.031,3.552 5.344,3.708 0.313,0.156 10 false *4 4.438,3.552 4.75,3.708 0.313,0.156 10 false *5
*1 ECM *2 Swirl Control Valve
*3 Vacuum Pump *4 Vacuum Switching Valve Assembly (for Swirl Control Valve)
*5 Swirl Control Valve Actuator - -


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P200873 After warming up engine, drive vehicle at an engine speed of 3200 rpm or more with high load for 1 minute or more.*

HINT:

*: When the above driving pattern cannot be performed due to road conditions, etc., the swirl control valve can be determined to be functioning normally if mass air flow is 84 gm/s or more and manifold absolute pressure is 105 kPa or higher when the engine speed is at 4000 rpm with no load. However, no DTCs are stored when inspecting the vehicle with this method.

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.


CAUTION / NOTICE / HINT

NOTICE:


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P200873)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / DTC.

Powertrain > Engine > Trouble Codes
50001 372

d.

Read the DTCs.

Result:
Result Proceed to
P200873 is output A
P200873 and other DTCs are output B


HINT:

When manifold absolute pressure sensor, mass air flow sub-assembly, intake air temperature sensor, and/or intake air temperature sensor (Turbo) related DTCs are stored along with P200873, perform troubleshooting for those DTCs first.

Manifold absolute pressure sensor-related DTCs: P010512 and P010514.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P010512

Mass air flow sub-assembly-related DTCs: P010012 and P010014.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P010012

Intake air temperature sensor-related DTCs: P011011 and P011015.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P011011

intake air temperature sensor (Turbo)-related DTCs: P007A11 and P007A15.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>P007A11




A

2.CHECK AIR INTAKE SYSTEM

B

2.CHECK AIR INTAKE SYSTEM
a.

Check for air leakage and blockage between the air cleaner cap and turbocharger sub-assembly, and between the turbocharger sub-assembly and intake manifold.

Result:
Result Proceed to
Leaks and/or blockages exist in the intake system A
No leaks or blockages in the intake system B


HINT:
·

Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.

·

Check if the air cleaner element is significantly dirty.

·

Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.

·

Check for any modifications in the intake system made by the user.





A

3.REPAIR OR REPLACE INTAKE SYSTEM

B

4.CHECK INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
3.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the intake system.


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 372 75

e.
A356877

Perform the Active Test.

OK:

Swirl control valve rod moves smoothly in the direction indicated by the arrow in the illustration.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (MASS AIR FLOW SENSOR AND INTAKE MANIFOLD ABSOLUTE PRESSURE)

NG

8.CHECK CONNECTION OF VACUUM HOSE
5.READ VALUE USING GTS (MASS AIR FLOW SENSOR AND INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor and Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
Intake Manifold Absolute Pressure
50003 372 215,385

e.

Take a snapshot when the engine speed is maintained at 4000 rpm with no load.


f.

Read the values of "Intake Manifold Absolute Pressure" and "Mass Air Flow Sensor" in the Data List using the snapshot review function.

Result:
Result Proceed to
Mass Air Flow Sensor 84 gm/s or more and Intake Manifold Absolute Pressure 105 kPa or higher C
Intake Manifold Absolute Pressure below 90 kPa B
Except above A


HINT:
·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc. Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.





A

6.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

B

7.INSPECT TURBOCHARGER NOZZLE VANE PLATE

C

END

6.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.



Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.INSPECT TURBOCHARGER NOZZLE VANE PLATE

b.

Inspect the turbocharger nozzle vane plate.

i.

Remove the e-washer from the turbocharger nozzle vane control actuator.



c.
A348999

Move the turbocharger vane control rod sub-assembly and check that the turbocharger nozzle vane support plate moves.


Result:
Result Proceed to
Catches, but operates* OK
Gets stuck and does not operate NG


HINT:

*: Check several times.



OK

NG

8.CHECK CONNECTION OF VACUUM HOSE
a.

Check the connection of the swirl control valve system vacuum hose.


Result:
Proceed to
OK
NG



OK

9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)

NG

15.REPAIR OR REPLACE VACUUM HOSE
9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
a.
A067588E23
0.458,1.438 0.313,1.677 false 0.667,1.396 0.917,1.885 true 2,1.417 1.844,1.646 false 2.177,1.375 2.5,1.844 true 0.823,0.031 1.531,0.24 0.708,0.208 10 false VSV is ON 2.458,0.021 3.24,0.229 0.781,0.208 10 false VSV is OFF 0.573,0.365 0.792,0.563 0.219,0.198 10 false Air 2.333,1.833 2.813,2.031 0.479,0.198 10 false Port E 0.771,1.906 1.25,2.104 0.479,0.198 10 false Port E 1.625,1.625 2.094,1.823 0.469,0.198 10 false Port F 0.104,1.688 0.573,1.885 0.469,0.198 10 false Port F 2.031,0.417 2.25,0.615 0.219,0.198 10 false Air 2.76,0.74 3.333,0.938 0.573,0.198 10 false Air Filter

Disconnect the vacuum hoses from the vacuum switching valve assembly (for swirl control valve).


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 372 75

e.

Check the VSV operation when it is operated using the GTS.

OK:
Tester Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.


Result:
Proceed to
OK
NG



OK

10.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY

NG

11.REPLACE VACUUM CONTROL VALVE SET
10.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Inspect the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>INSPECTION

HINT:
·

If there are any deposits adhering to the valve, clean the valve. When cleaning the valve, use diesel fuel or kerosene.

·

When inspecting the electric EGR control valve assembly, make sure that the valve is fully closed.




Result:
Proceed to
OK
NG



OK

14.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)

NG

13.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
11.REPLACE VACUUM CONTROL VALVE SET
a.

Replace the vacuum control valve set.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>REMOVAL

HINT:

Before replacing the vacuum control valve set, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE)
a.
A067588E23
0.458,1.438 0.313,1.677 false 0.667,1.396 0.917,1.885 true 2,1.417 1.844,1.646 false 2.177,1.375 2.5,1.844 true 0.823,0.031 1.531,0.24 0.708,0.208 10 false VSV is ON 2.458,0.021 3.24,0.229 0.781,0.208 10 false VSV is OFF 0.573,0.365 0.792,0.563 0.219,0.198 10 false Air 2.333,1.833 2.813,2.031 0.479,0.198 10 false Port E 0.771,1.906 1.25,2.104 0.479,0.198 10 false Port E 1.625,1.625 2.094,1.823 0.469,0.198 10 false Port F 0.104,1.688 0.573,1.885 0.469,0.198 10 false Port F 2.031,0.417 2.25,0.615 0.219,0.198 10 false Air 2.76,0.74 3.333,0.938 0.573,0.198 10 false Air Filter

Disconnect the vacuum hoses from the vacuum switching valve assembly (for swirl control valve).


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Swirl Control Valve.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Swirl Control Valve
50004 372 75

e.

Check the VSV operation when it is operated using the GTS.

OK:
Tester Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter



f.

Reconnect the vacuum hoses.


Result:
Proceed to
OK
NG



OK

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

16.REPLACE ECM
13.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EGR VALVE (w/ EGR Cooler)>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
14.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION)
a.

Inspect the intake manifold (swirl control valve).

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>INSPECTION

HINT:
·

If there are any deposits adhering to the valve, clean the valve.

·

If there are any deposits adhering to the valve, clean the valve. When cleaning the valve, use diesel fuel or kerosene.

·

Apply vacuum to the diaphragm of the swirl control valve and check that the valve opens and closes smoothly.




Result:
Proceed to
OK
NG



OK

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

18.REPLACE INTAKE MANIFOLD
15.REPAIR OR REPLACE VACUUM HOSE
a.

Repair or replace the vacuum hose.


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).


d.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor and Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
Intake Manifold Absolute Pressure
50003 372 215,385

e.

Take a snapshot when the engine speed is maintained at 4000 rpm with no load.


f.

Read the values of "Mass Air Flow Sensor" and "Intake Manifold Absolute Pressure" in the Data List using the snapshot review function.

OK:

Mass Air Flow Sensor is 84 gm/s or more and Intake Manifold Absolute Pressure is 105 kPa or higher.


HINT:
·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.

·

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc. Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.




Result:
Proceed to
NEXT



NEXT

END

18.REPLACE INTAKE MANIFOLD
a.

Replace the intake manifold (swirl control valve).

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE MANIFOLD>REMOVAL


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED