A No. 2 nitrogen oxides sensor is installed in the front exhaust pipe assembly in order to detect the concentration of NOx and O2 in the exhaust gas.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P013613 | O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open | No. 2 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic) |
No. 2 nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P0136 |
| P229E11 | NOx Sensor Circuit Low Bank 1 Sensor 2 Circuit Short to Ground | No. 2 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic) |
No. 2 nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P22A0 |
| P229E12 | NOx Sensor Circuit High Bank 1 Sensor 2 Circuit Short to Battery | No. 2 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic) |
No. 2 nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P22A1 |
| P229E13 | NOx Sensor Circuit Low Bank 1 Sensor 2 Circuit Open | No. 2 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic) |
No. 2 nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P229E |
| P22A312 | NOx Sensor Heater Control Circuit High Bank 1 Sensor 2 Circuit Short to Battery | No. 2 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic) |
No. 2 nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P22A5 |
| P22A314 | NOx Sensor Heater Control Circuit Low Bank 1 Sensor 2 Circuit Short to Ground or Open | No. 2 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic) |
No. 2 nitrogen oxides sensor | Comes on | DTC stored | SAE Code: P22A4 |
| DTC No. | Data List |
|---|---|
| P013613
P229E11 P229E12 P229E13 P22A312 P22A314 |
NOx Density B1S2 |
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P013613
P229E11 P229E12 P229E13 P22A312 P22A314 |
Ignition switch ON for 3 seconds or more |
Refer to DTC U029D87.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P013613, P229E11, P229E12, P229E13, P22A312 or P22A314 is output | A |
| DTC P013613, P229E11, P229E12, P229E13, P22A312 or P22A314 and other DTCs are output* | B |
*: If any other DTCs are output, perform troubleshooting for those DTCs first.
A
B
Replace the No. 2 nitrogen oxides sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON for 3 seconds or more.
Confirm that the pending DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input DTC P013613, P229E11, P229E12, P229E13, P22A312 or P22A314.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE, turn the ignition switch to ON for 3 seconds or more, and then check "All Readiness" again.
| Proceed to |
|---|
| NEXT |
NEXT