Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › 2020.05–2020.06
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  U029D87  Lost Communication with NOx Sensor "A" Missing Message  U029E87  Lost Communication with NOx Sensor "B" Missing Message  


DESCRIPTION

The ECM sends and receives data to and from the No. 1 nitrogen oxides sensor and No. 2 nitrogen oxides sensor via local CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
U029D87 Lost Communication with NOx Sensor "A" Missing Message Communication stops between the ECM and the No. 1 nitrogen oxides sensor for 1 second or more.
(1 trip detection logic)
·

No. 1 nitrogen oxides sensor

·

Harness or connector

·

ECM


Comes on DTC stored SAE Code: U029D
U029E87 Lost Communication with NOx Sensor "B" Missing Message Communication stops between the ECM and the No. 2 nitrogen oxides sensor for 1 second or more.
(1 trip detection logic)
·

No. 2 nitrogen oxides sensor

·

Harness or connector

·

ECM


Comes on DTC stored SAE Code: U029E

MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the No. 1 nitrogen oxides sensor, No. 2 nitrogen oxides sensor and ECM.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
U029D87
U029E87
Ignition switch ON and wait for 1 second or more

WIRING DIAGRAM

A456724E05
3.635,3.104 5.771,3.365 2.135,0.26 10 false No. 1 Nitrogen Oxides Sensor 3.646,2.958 4.104,3.156 0.458,0.198 10 false A24 3.625,1.677 5.76,1.938 2.135,0.26 10 false No. 2 Nitrogen Oxides Sensor 3.635,1.531 4.094,1.729 0.458,0.198 10 false Y3 4.229,1.208 4.688,1.406 0.458,0.198 10 false GND 4.229,0.781 4.688,0.979 0.458,0.198 10 false BATT 4.729,1.115 5.188,1.313 0.458,0.198 10 false CAN- 4.729,0.781 5.188,0.979 0.458,0.198 10 false CAN+ 4.073,0.667 4.229,0.865 0.156,0.198 10 false 5 4.073,1.083 4.229,1.281 0.156,0.198 10 false 4 5.177,0.635 5.333,0.833 0.156,0.198 10 false 2 5.177,0.969 5.333,1.167 0.156,0.198 10 false 3 5.854,1.979 6.167,2.156 0.313,0.177 10 false 27 5.844,2.396 6.25,2.594 0.406,0.198 10 false 35 5.167,2.406 5.323,2.604 0.156,0.198 10 false 3 5.177,1.948 5.333,2.146 0.156,0.198 10 false 2 4.073,2 4.229,2.198 0.156,0.198 10 false 5 4.083,2.271 4.24,2.469 0.156,0.198 10 false 4 4.083,2.542 4.24,2.74 0.156,0.198 10 false 1 6.115,2.146 6.573,2.344 0.458,0.198 10 false CANU 6.125,2.552 6.583,2.75 0.458,0.198 10 false CAND 4.74,2.146 5.198,2.344 0.458,0.198 10 false CAN+ 4.76,2.563 5.219,2.76 0.458,0.198 10 false CAN- 4.229,2.115 4.688,2.313 0.458,0.198 10 false BATT 4.229,2.365 4.688,2.563 0.458,0.198 10 false GND 4.229,2.625 4.688,2.823 0.458,0.198 10 false ADSW 3,2.115 3.458,2.313 0.458,0.198 10 false 1E 3.042,1.917 3.5,2.115 0.458,0.198 10 false 3 2.99,3.708 3.448,3.906 0.458,0.198 10 false 1E 3.042,3.552 3.5,3.75 0.458,0.198 10 false 8 2.542,3.375 3.552,3.646 1.01,0.271 10 false EFI NO. 2 2.01,2.875 3.021,3.146 1.01,0.271 10 false NOX 1.802,3.99 2.813,4.26 1.01,0.271 10 false E/G W/PMP 1.271,3.365 1.771,3.75 0.5,0.385 10 false E/G W/ PMP 1.354,2.271 2.365,2.542 1.01,0.271 10 false NOX 2.604,5.115 2.76,5.313 0.156,0.198 10 false 2 1.26,1.99 1.417,2.188 0.156,0.198 10 false 1 1.677,3.135 1.833,3.333 0.156,0.198 10 false 2 1.281,3.135 1.438,3.333 0.156,0.198 10 false 1 0.74,3.042 0.896,3.24 0.156,0.198 10 false 1 0.75,3.229 1.208,3.427 0.458,0.198 10 false A 0.698,3.719 1.156,3.917 0.458,0.198 10 false 1E 0.75,3.542 0.906,3.74 0.156,0.198 10 false 4 0.385,5.26 1.396,5.531 1.01,0.271 10 false FL MAIN 0.688,4.958 1.698,5.229 1.01,0.271 10 false EFI-MAIN 2.021,5.563 3.031,5.833 1.01,0.271 10 false EFI MAIN 2.948,4.958 3.958,5.229 1.01,0.271 10 false EFI NO. 3 6.115,5.229 6.573,5.427 0.458,0.198 10 false MREL 5.813,5.083 6.073,5.281 0.26,0.198 10 false 14 6.333,5.979 6.792,6.177 0.458,0.198 10 false N2 6.26,6.146 6.719,6.344 0.458,0.198 10 false ECM 3.073,5.979 5.208,6.24 2.135,0.26 10 false : CAN Communication Line 1.198,4.323 3.333,4.583 2.135,0.26 10 false No. 1 Integration Relay 0.573,5.854 1.583,6.125 1.01,0.271 10 false Battery 1.854,5.104 2.01,5.302 0.156,0.198 10 false 1 1.854,4.719 2.313,4.917 0.458,0.198 10 false 3 2.615,4.698 2.771,4.896 0.156,0.198 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON and turn the GTS on.


c.

According to the display on the GTS, select "Health Check".


d.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U029D87 is output A
DTC U029E87 is output B
DTC U029D87 and U029E87 are output C




A

2.CHECK NO. 1 NITROGEN OXIDES SENSOR

B

3.CHECK NO. 2 NITROGEN OXIDES SENSOR

C

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SENSOR)
2.CHECK NO. 1 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Turn the ignition switch to ON.


c.
A383897C23
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.552,0.292 2.125,0.51 0.573,0.219 10 false A24 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-5 (BATT) - A24-4 (GND) Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-2 (CAN+) - A24-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A24-2 (CAN+) or A24-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A24-2 (CAN+) or A24-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A24-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK NO. 2 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 2 nitrogen oxides sensor connector.


b.

Turn the ignition switch to ON.


c.
A383897C24
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.646,0.292 2.219,0.51 0.573,0.219 10 false Y3 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Y3-5 (BATT) - Y3-4 (GND) Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y3-2 (CAN+) - Y3-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
Y3-2 (CAN+) or Y3-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Y3-2 (CAN+) or Y3-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
Y3-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SENSOR)
A383897C75
1,0.198 1.479,0.531 0.479,0.333 1.927,0.198 2.406,0.531 0.479,0.333 2.479,1.76 2.219,1.271 true 1.677,1.76 1.896,1.281 true 2.479,0.271 2.792,0.469 0.313,0.198 10 false *b 1.135,0.292 1.708,0.51 0.573,0.219 10 false A24 1.51,1.792 1.969,1.99 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 2.094,0.281 2.667,0.5 0.573,0.219 10 false Y3 1.542,0.271 1.854,0.469 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)
*b Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)


a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Disconnect the No. 2 nitrogen oxides sensor connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-5 (BATT) - A24-4 (GND) Ignition switch ON 11 to 14 V
Y3-5 (BATT) - Y3-4 (GND) Ignition switch ON 11 to 14 V



d.

Reconnect the No. 2 nitrogen oxides sensor connector.


e.

Reconnect the No. 1 nitrogen oxides sensor connector.


Result:
Proceed to
OK
NG



OK

5.CHECK ECM

NG

8.CHECK HARNESS AND CONNECTOR (SENSOR CONNECTOR - BODY GROUND)
5.CHECK ECM
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.
A449464C02
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.854,0.479 2.313,0.677 0.458,0.198 10 false N2 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-27 (CANU) - N2-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N2-27 (CANU) or N2-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N2-27 (CANU) or N2-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

6.CHECK NO. 1 NITROGEN OXIDES SENSOR
6.CHECK NO. 1 NITROGEN OXIDES SENSOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Disconnect the No. 1 nitrogen oxides sensor connector.


d.
A449464C02
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.854,0.479 2.313,0.677 0.458,0.198 10 false N2 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-27 (CANU) - N2-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N2-27 (CANU) or N2-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N2-27 (CANU) or N2-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

7.CHECK NO. 2 NITROGEN OXIDES SENSOR
7.CHECK NO. 2 NITROGEN OXIDES SENSOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Disconnect the No. 2 nitrogen oxides sensor connector.


d.
A449464C02
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.854,0.479 2.313,0.677 0.458,0.198 10 false N2 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-27 (CANU) - N2-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
N2-27 (CANU) or N2-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N2-27 (CANU) or N2-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SENSOR CONNECTOR - BODY GROUND)
A383897C76
1,0.198 1.479,0.531 0.479,0.333 1.927,0.198 2.406,0.531 0.479,0.333 1.677,1.76 1.896,1.281 true 2.479,0.271 2.792,0.469 0.313,0.198 10 false *b 1.135,0.292 1.708,0.51 0.573,0.219 10 false A24 1.51,1.792 1.969,1.99 0.458,0.198 10 false GND 2.094,0.281 2.667,0.5 0.573,0.219 10 false Y3 1.542,0.271 1.854,0.469 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)
*b Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)


a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Disconnect the No. 2 nitrogen oxides sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-4 (GND) - Body ground Always Below 1 Ω
Y3-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 NITROGEN OXIDES SENSOR, NO. 2 NITROGEN OXIDES SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 NITROGEN OXIDES SENSOR, NO. 2 NITROGEN OXIDES SENSOR)
a.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the No. 1 nitrogen oxides sensor connector.


c.

Disconnect the No. 2 nitrogen oxides sensor connector.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
1E-3 - A24-5 (BATT) Always Below 1 Ω
1E-3 - Y3-5 (BATT) Always Below 1 Ω
1E-3 - A24-5 (BATT) - Body ground and other terminals Always 10 kΩ or higher
1E-3 - Y3-5 (BATT) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

10.INSPECT NO. 1 INTEGRATION RELAY (NOX RELAY AND E/G W/PMP RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT NO. 1 INTEGRATION RELAY (NOX RELAY AND E/G W/PMP RELAY)
a.

Inspect the No. 1 integration relay (NOX relay).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION


b.

Inspect the No. 1 integration relay (E/G W/PMP relay).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)

NG

REPLACE NO. 1 INTEGRATION RELAY

11.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
A443534C01
0.573,2.698 0.875,2.927 0.302,0.229 0.677,2.729 0.833,2.927 0.156,0.198 10 false A 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a
*a No. 1 Engine Room Relay Block and Junction Block Assembly without No. 1 Integration Relay


a.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)

12.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - EFI MAIN RELAY)
a.

Remove the EFI MAIN relay from the No. 1 engine room relay block and junction block assembly.


b.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-8 - EFI MAIN relay terminal 5 Always Below 1 Ω
1E-8 or EFI MAIN relay terminal 5 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR