Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EXHAUST GAS TEMPERATURE SENSOR › from 2020.05
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0384174 EXHAUST GAS TEMPERATURE SENSOR A

1GD-FTV EMISSION CONTROL  EXHAUST GAS TEMPERATURE SENSOR  INSTALLATION  


PROCEDURE

Hide 89425 1.INSTALL EXHAUST GAS TEMPERATURE SENSOR

a.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the No. 3 exhaust gas temperature sensor to the exhaust manifold converter sub-assembly.

Torque:

Specified tightening torque

30 N*m (306 kgf*cm, 22 ft.*lbf)


NOTICE:
·

If the No. 3 exhaust gas temperature sensor is dropped, replace it with a new one.

·

When reusing the No. 3 exhaust gas temperature sensors, clean the screws and apply anti-seize compound before installing the No. 3 exhaust gas temperature sensor.



HINT:
·

The connector color of the No. 3 exhaust gas temperature sensor is gray.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)




b.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the No. 2 exhaust gas temperature sensor to the exhaust manifold converter sub-assembly.

Torque:

Specified tightening torque

30 N*m (306 kgf*cm, 22 ft.*lbf)


NOTICE:
·

If the No. 2 exhaust gas temperature sensor is dropped, replace it with a new one.

·

When reusing the No. 2 exhaust gas temperature sensors, clean the screws and apply anti-seize compound before installing the No. 2 exhaust gas temperature sensor.



HINT:
·

The connector color of the No. 2 exhaust gas temperature sensor is black.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)




c.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 14 mm union nut wrench, install the exhaust gas temperature sensor to the exhaust manifold converter sub-assembly.

Torque:

Specified tightening torque

30 N*m (306 kgf*cm, 22 ft.*lbf)


NOTICE:
·

If the No. 3 exhaust gas temperature sensor is dropped, replace it with a new one.

·

When reusing the exhaust gas temperature sensors, clean the screws and apply anti-seize compound before installing the exhaust gas temperature sensor.



HINT:
·

The connector color of the exhaust gas temperature sensor is white.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)




d.
A440874C01
1.99,0.594 2.333,0.396 2.333,0.396 2.552,0.396 true 1.615,0.51 1.229,0.208 1.229,0.208 1,0.208 true 1.198,0.615 0.854,0.698 0.854,0.698 0.677,0.698 true 2.573,0.281 2.781,0.458 0.208,0.177 10 true *a 0.781,0.115 0.979,0.271 0.198,0.156 10 true *b 0.448,0.594 0.677,0.75 0.229,0.156 10 true *c
*a White
*b Black
*c Gray


Attach the 3 colored connectors to the pipe clamp in the positions shown in the illustration.


e.

Close the clamp of the pipe clamp, and install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Arrange the exhaust gas temperature sensor wires so that they do not contact each other.



f.

Connect the No. 3 exhaust gas temperature sensor to the No. 1 vacuum pipe.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


g.

for Air Cooled Type Intercooler:

Connect the 3 connectors to the 3 exhaust gas temperature sensor.


h.

for Water Cooled Type Intercooler:

i.

Connect the 3 connectors to the 3 exhaust gas temperature sensors.


ii.

Attach the clamp and connect the engine wire to the intercooler support bracket with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



Hide 17940D 2.INSTALL INTERCOOLER ASSEMBLY (for Water Cooled Type Intercooler)

Hide 12601B 3.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Cover)