Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.06
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P24AE12  Particulate Matter Sensor Circuit High Circuit Short to Battery  P24AE14  Particulate Matter Sensor Circuit Low Circuit Short to Ground or Open  P24AE96  Particulate Matter Sensor Circuit Range/Performance Component Internal Failure  P24B301  Particulate Matter Sensor Heater Control Circuit/Open General Electrical Failure  P24C601  Particulate Matter Sensor Temperature Circuit General Electrical Failure  P24D000  Particulate Matter Sensor Supply Voltage Circuit Low  


DESCRIPTION

The particulate matter sensor is installed in the center exhaust pipe assembly to detect the PM value.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P24AE12 Particulate Matter Sensor Circuit High Circuit Short to Battery Open or short in particulate matter sensor circuit for 10 seconds or more
(2 trip detection logic)
Particulate matter sensor Comes on DTC stored SAE Code: P24B1
P24AE14 Particulate Matter Sensor Circuit Low Circuit Short to Ground or Open Open or short in particulate matter sensor circuit for 10 seconds or more
(2 trip detection logic)
Particulate matter sensor Comes on DTC stored SAE Code: P24B0
P24AE96 Particulate Matter Sensor Circuit Range/Performance Component Internal Failure Particulate matter sensor out of range for 3 seconds or more
(2 trip detection logic)
Particulate matter sensor Comes on DTC stored SAE Code: P24AF
P24B301 Particulate Matter Sensor Heater Control Circuit/Open General Electrical Failure Malfunction in particulate matter sensor circuit for 10 seconds or more
(2 trip detection logic)
Particulate matter sensor Comes on DTC stored SAE Code: P24B3
P24C601 Particulate Matter Sensor Temperature Circuit General Electrical Failure Malfunction in particulate matter sensor temperature sensor for 10 seconds or more
(2 trip detection logic)
Particulate matter sensor Comes on DTC stored SAE Code: P24C6
P24D000 Particulate Matter Sensor Supply Voltage Circuit Low Low power supply to particulate matter sensor circuit for 10 seconds or more
(2 trip detection logic)
·

Particulate matter sensor

·

NOX relay

·

Harness or connector


Comes on DTC stored SAE Code: P24D0

Related Data List
DTC No. Data List
P24AE12
P24AE14
P24AE96
P24B301
P24C601
P24D000
·

PM Sensor Output Current

·

Status of PM Sensor IDE Circuit

·

Status of PM Sensor IDE (+ Side)

·

Status of PM Sensor Temperature

·

Status of PM Sensor IDE (- Side)

·

Status of PM Sensor Heater ON Malfunction

·

Status of PM Sensor Heater OFF Malfunction



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P24AE12
P24AE14
P24AE96
P24B301
P24C601
P24D000
Ignition switch ON and wait for 10 seconds or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and Transmission > Trouble Codes
50001 372

Result:
Result Proceed to
DTC P24D000 is output A
DTC P24AE12, P24AE14, P24AE96, P24B301, P24C601, P24D000 is output B
DTC P24AE12 or P24AE14, P24AE96, P24B301, P24C601, P24D000 and other DTCs are output* C


HINT:

*: If any other DTCs (CAN communication malfunctions or open/short circuits) are output, perform troubleshooting for those DTCs first.



A

2.INSPECT NOX RELAY

B

7.REPLACE PARTICULATE MATTER SENSOR

C

2.INSPECT NOX RELAY

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NOX RELAY - PARTICULATE MATTER SENSOR ASSEMBLY)

NG

6.REPLACE NOX RELAY
3.CHECK HARNESS AND CONNECTOR (NOX RELAY - PARTICULATE MATTER SENSOR ASSEMBLY)
a.

Disconnect the particulate matter sensor assembly connector.


b.

Remove the No. 1 integration relay from the No. 1 engine room relay block and junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
1E-3 - Y4-1 (BATT) Always Below 1 Ω
1E-3 - Y4-1 (BATT) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

7.REPLACE PARTICULATE MATTER SENSOR

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine and Transmission > Clear DTCs
50002 372

d.

Turn the ignition switch off and wait for 30 seconds.


e.

Turn the ignition switch to ON and wait for 10 second or more.


f.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.

Powertrain > Engine and Transmission > Trouble Codes
50001 372

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

6.REPLACE NOX RELAY
a.

Replace the NOX relay.


Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE PARTICULATE MATTER SENSOR
a.

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED