Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2020.06–2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0382589 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P070312  Brake Switch "B" Circuit Short to Battery  


DESCRIPTION

The stop light switch is part of a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P070312 Brake Switch "B" Circuit Short to Battery Stop light switch remains on even when vehicle is driven in GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (1.8 mph)) pattern 5 times (2 trip detection logic).
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Comes on DTC stored SAE Code: P0724

Related Data List
DTC No. Data List
P070312 Stop Light SW

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P070312 Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Stop Light SW.

Powertrain > Engine > Data List
Tester Display
Stop Light SW
50003 372 12

d.

Read the value displayed on the GTS when the brake pedal is depressed and released.

OK:
Brake Pedal Display
Released OFF
Depressed ON



Result:
Proceed to
OK
NG



OK

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP VOLTAGE)

NG

7.REPLACE STOP LIGHT SWITCH ASSEMBLY
3.CHECK ECM (STP VOLTAGE)
a.
A107724C53
2.771,2.542 3.146,2.813 0.375,0.271 2.865,3.969 3,3.26 true 0.667,0.531 0.979,0.729 0.313,0.198 10 false *a 2.125,0.51 2.438,0.708 0.313,0.198 10 false *b 0.167,2.219 0.479,2.417 0.313,0.198 10 false *c 2.875,2.604 3.188,2.802 0.313,0.198 10 false A2 2.688,4.021 3.354,4.219 0.667,0.198 10 false 13 (STP)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
A2-13 (STP) - Body ground Released 0 to 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Start the engine.


f.

Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times or more.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P070312.


iii.

Check that STATUS is NORMAL.

HINT:
·

If STATUS is NORMAL, DTC judgment is complete and it can be determined that the system is normal.

·

If STATUS is INCOMPLETE, DTC judgment is incomplete. Perform the following procedure again 5 times: accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less.





Result:
Proceed to
NEXT



NEXT

END

7.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED