Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2019.02–2021.07
RM35X0E _57 Power Source / Network _078518 NETWORKING _0381088 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 3 Line  


DESCRIPTION

Symptom Trouble Area

*1: for Radio and Display Type

*2: w/ Telematics System

There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that store a communication stop history on the "Detail" screen.
·

CAN main bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

Radio and display receiver assembly*1

·

Telephone transceiver assembly*2

·

No. 7 CAN junction connector



WIRING DIAGRAM

C413729E05
3.177,2.552 3.792,2.75 0.615,0.198 10 false N127 3.177,2.74 4.406,3.104 1.229,0.365 10 false No. 7 CAN Junction Connector 3.396,0.271 4.01,0.469 0.615,0.198 10 false 11 3.396,0.667 4.01,0.865 0.615,0.198 10 false 22 4.052,0.271 4.667,0.469 0.615,0.198 10 false 9 4.052,0.656 4.667,0.854 0.615,0.198 10 false 20 5.344,0.917 6.167,1.208 0.823,0.292 10 false O7 5.344,1.073 7.042,1.635 1.698,0.563 10 false Radio and Display Receiver Assembly*1 0.125,3.458 3,3.729 2.875,0.271 10 false *1: for Radio and Display Type 6.031,0.781 6.646,0.979 0.615,0.198 10 false CANL 6.031,0.385 6.646,0.583 0.615,0.198 10 false CANH 5.771,0.271 6.385,0.469 0.615,0.198 10 false 13 5.771,0.677 6.385,0.875 0.615,0.198 10 false 14 0.885,1.854 1.5,2.052 0.615,0.198 10 false CAYH 0.875,2.438 1.49,2.635 0.615,0.198 10 false CAYL 1.365,1.865 1.979,2.063 0.615,0.198 10 false 19 1.375,2.25 1.99,2.448 0.615,0.198 10 false 20 3.406,2.271 4.021,2.469 0.615,0.198 10 false 21 3.406,1.854 4.021,2.052 0.615,0.198 10 false 10 4.042,2.25 4.656,2.448 0.615,0.198 10 false 19 4.073,1.865 4.688,2.063 0.615,0.198 10 false 8 5.438,2.49 6.052,2.688 0.615,0.198 10 false N74 5.781,1.865 6.396,2.063 0.615,0.198 10 false 15 5.76,2.24 6.375,2.438 0.615,0.198 10 false 16 6.042,2.354 6.656,2.552 0.615,0.198 10 false CANN 6.031,1.979 6.646,2.177 0.615,0.198 10 false CANP 5.406,2.667 6.792,3.417 1.385,0.75 10 false Telephone Transceiver Assembly*2 2.917,3.479 4.927,3.729 2.01,0.25 10 false *2: w/ Telematics System 0.885,0.292 1.5,0.49 0.615,0.198 10 false CA3H 0.896,0.875 1.51,1.073 0.615,0.198 10 false CA3L 0.167,2.448 0.781,2.646 0.615,0.198 10 false N21 0.177,2.646 2.135,3.073 1.958,0.427 10 false Central Gateway ECU (Network Gateway ECU) 1.365,0.281 1.979,0.479 0.615,0.198 10 false 6 1.396,0.698 2.01,0.896 0.615,0.198 10 false 21

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C368243C51
1.448,0.104 1.917,0.323 0.469,0.219 0.99,1.75 1.198,1.75 1.198,1.75 1.396,1.104 true 1.073,0.5 1.281,0.5 1.281,0.5 1.406,0.979 true 0.625,1.667 1.083,1.865 0.458,0.198 10 false CA3L 1.573,0.135 2.031,0.333 0.458,0.198 10 false N21 0.677,0.427 1.135,0.625 0.458,0.198 10 false CA3H 0.083,0.063 0.542,0.26 0.458,0.198 10 false *a
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-6 (CA3H) - N21-21 (CA3L) Cable disconnected from negative (-) battery terminal Below 70 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS WIRES

NG

29.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
2.CHECK FOR SHORT IN CAN BUS WIRES
a.
C368243C51
1.448,0.104 1.917,0.323 0.469,0.219 0.99,1.75 1.198,1.75 1.198,1.75 1.396,1.104 true 1.073,0.5 1.281,0.5 1.281,0.5 1.406,0.979 true 0.625,1.667 1.083,1.865 0.458,0.198 10 false CA3L 1.573,0.135 2.031,0.333 0.458,0.198 10 false N21 0.677,0.427 1.135,0.625 0.458,0.198 10 false CA3H 0.083,0.063 0.542,0.26 0.458,0.198 10 false *a
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-6 (CA3H) - N21-21 (CA3L) Cable disconnected from negative (-) battery terminal 54 Ω or higher



Result:
Proceed to
OK
NG



OK

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE

NG

21.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE
a.
C324419C62
1.448,0.25 1.917,0.51 0.469,0.26 1.427,2.365 1.896,2.625 0.469,0.26 1.396,1.021 1.229,0.438 1.229,0.438 1.063,0.438 true 2.365,3.604 2.031,4.271 2.031,4.271 1.865,4.271 true 1.417,1.146 1.25,1.76 1.25,1.76 1.083,1.76 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.115,2.198 0.427,2.396 0.313,0.198 10 false *b 1.552,0.302 2.042,0.552 0.49,0.25 10 false N21 1.531,2.417 2.021,2.667 0.49,0.25 10 false N8 0.677,0.365 1.167,0.615 0.49,0.25 10 false CA3H 1.573,4.188 2.063,4.438 0.49,0.25 10 false BAT 0.74,1.677 1.229,1.927 0.49,0.25 10 false CA3L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-6 (CA3H) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N21-21 (CA3L) - N8-16 (BAT)



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE

NG

13.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE
a.
C324419C63
1.448,0.25 1.917,0.51 0.469,0.26 1.427,2.365 1.896,2.625 0.469,0.26 1.396,1.021 1.229,0.438 1.229,0.438 1.063,0.438 true 1.625,3.26 1.344,4.083 1.344,4.083 1.177,4.083 true 1.417,1.146 1.25,1.76 1.25,1.76 1.083,1.76 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.115,2.198 0.427,2.396 0.313,0.198 10 false *b 1.552,0.302 2.042,0.552 0.49,0.25 10 false N21 1.531,2.417 2.021,2.667 0.49,0.25 10 false N8 0.677,0.365 1.167,0.615 0.49,0.25 10 false CA3H 0.958,4 1.448,4.25 0.49,0.25 10 false CG 0.74,1.677 1.229,1.927 0.49,0.25 10 false CA3L
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-6 (CA3H) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N21-21 (CA3L) - N8-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)
a.
C414215C01
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.656,0.646 2.438,0.646 2.438,0.646 2.292,1.26 true 2.052,1.49 1.781,2.292 1.781,2.292 1.615,2.292 true 2.146,4.24 1.979,4.24 1.979,4.24 1.646,3.302 true 2.542,2.156 2.323,2.156 2.323,2.156 2.188,1.51 true 1.906,1.49 1.635,2.125 1.635,2.125 1.469,2.125 true 1.573,0.292 2.188,0.49 0.615,0.198 10 false N21 1.573,2.573 2.188,2.771 0.615,0.198 10 false N8 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 1.229,2.219 1.844,2.417 0.615,0.198 10 false CAYL 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 2.698,0.573 3.229,0.781 0.531,0.208 10 false CA3H 2.229,4.167 2.844,4.365 0.615,0.198 10 false CG 2.646,2.083 3.177,2.292 0.531,0.208 10 false CA3L 1.073,2.052 1.688,2.25 0.615,0.198 10 false CAYH
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the N21 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-6 (CA3H) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N21-21 (CA3L) - N8-4 (CG)
N21-19 (CAYH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N21-20 (CAYL) - N8-4 (CG)



c.

Reconnect the N21 central gateway ECU (network gateway ECU) connector.


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
6.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N127 No. 7 CAN junction connector.

C414290C17
2.021,0.25 2.427,0.5 0.406,0.25 5.167,0.552 5.573,0.802 0.406,0.25 3.552,1.375 3.365,1.375 3.365,1.375 3.094,1.531 true 3.573,1.99 3.396,1.99 3.396,1.99 3.104,1.844 true 5.708,2.229 5.531,2.229 5.531,2.229 5.302,1.51 true 3.552,1.073 3.365,1.073 3.365,1.073 2.927,1.542 true 3.438,2.208 3.26,2.208 3.26,2.208 2.917,1.833 true 0.135,0.094 0.531,0.365 0.396,0.271 10 false *a 2.063,0.292 2.563,0.531 0.5,0.24 10 false N127 3.594,1.313 4.26,1.552 0.667,0.24 10 false CANH*c 3.604,1.917 4.271,2.156 0.667,0.24 10 false CANL*c 4.292,0.094 4.635,0.406 0.344,0.313 10 false *b 5.281,0.604 5.781,0.844 0.5,0.24 10 false N8 5.75,2.146 6.417,2.385 0.667,0.24 10 false CG 3.594,0.99 4.26,1.229 0.667,0.24 10 false CANH*c 3.49,2.125 4.156,2.365 0.667,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to Central Gateway ECU (Network Gateway ECU) - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
N127-11 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
N127-22 (CANL) - N8-4 (CG)
N127-10 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
N127-21 (CANL) - N8-4 (CG)



c.

Reconnect the N127 No. 7 CAN junction connector.


Result:
Proceed to
OK
NG



OK

7.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

7.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for Radio and Display Type A
except Radio and Display Type B



A

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

9.CHECK VEHICLE TYPE
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the N127 No. 7 CAN junction connector.

C414290C18
2.021,0.25 2.427,0.5 0.406,0.25 5.167,0.552 5.573,0.802 0.406,0.25 5.708,2.229 5.531,2.229 5.531,2.229 5.302,1.51 true 3.219,2.375 3.042,2.375 3.042,2.375 2.74,1.833 true 3.438,0.76 3.25,0.76 3.25,0.76 2.74,1.542 true 0.135,0.094 0.531,0.365 0.396,0.271 10 false *a 2.063,0.292 2.563,0.531 0.5,0.24 10 false N127 3.26,2.302 3.927,2.542 0.667,0.24 10 false CANL*c 4.292,0.094 4.635,0.406 0.344,0.313 10 false *b 5.281,0.604 5.781,0.844 0.5,0.24 10 false N8 5.75,2.146 6.417,2.385 0.667,0.24 10 false CG 3.479,0.688 4.146,0.927 0.667,0.24 10 false CANH*c
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to Radio and Display Receiver Assembly - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
N127-9 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly
N127-20 (CANL) - N8-4 (CG)



c.

Reconnect the N127 No. 7 CAN junction connector.


Result:
Proceed to
OK
NG



OK

9.CHECK VEHICLE TYPE

NG

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
9.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Telematics System A
w/o Telematics System B



A

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - TELEPHONE TRANSCEIVER ASSEMBLY)

B

REPLACE NO. 7 CAN JUNCTION CONNECTOR

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the N127 No. 7 CAN junction connector.

C414290C19
2.021,0.25 2.427,0.5 0.406,0.25 5.167,0.552 5.573,0.802 0.406,0.25 5.708,2.229 5.531,2.229 5.531,2.229 5.302,1.51 true 2.99,2.563 2.813,2.563 2.813,2.563 2.563,1.833 true 3.229,0.521 3.042,0.521 3.042,0.521 2.573,1.531 true 0.135,0.094 0.531,0.365 0.396,0.271 10 false *a 2.063,0.292 2.563,0.531 0.5,0.24 10 false N127 4.292,0.094 4.635,0.406 0.344,0.313 10 false *b 5.281,0.604 5.781,0.844 0.5,0.24 10 false N8 5.75,2.146 6.417,2.385 0.667,0.24 10 false CG 3.281,0.438 3.948,0.677 0.667,0.24 10 false CANH*c 3.073,2.49 3.74,2.729 0.667,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to Telephone Transceiver Assembly - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
N127-8 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Telephone transceiver assembly
N127-19 (CANL) - N8-4 (CG)



c.

Reconnect the N127 No. 7 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 7 CAN JUNCTION CONNECTOR

NG

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (TELEPHONE TRANSCEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
a.
C414320C01
1.51,0.219 1.927,0.479 0.417,0.26 1.51,2.521 1.927,2.781 0.417,0.26 1.99,1.552 2.167,0.729 2.167,0.729 2.313,0.729 true 1.521,0.729 1.667,0.729 1.667,0.729 1.865,1.552 true 1.625,3.417 1.854,4.292 1.854,4.292 2,4.292 true 0.094,0.083 0.458,0.365 0.365,0.281 10 false *a 0.083,2.5 0.448,2.802 0.365,0.302 10 false *b 1.635,0.271 1.927,0.479 0.292,0.208 10 false O7 1.635,2.573 1.927,2.781 0.292,0.208 10 false N8 2.354,0.656 2.969,0.854 0.615,0.198 10 false CANL 1.104,0.656 1.719,0.854 0.615,0.198 10 false CANH 2.042,4.208 2.656,4.406 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of DLC3


Disconnect the O7 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-13 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
O7-14 (CANL) - N8-4 (CG)



c.

Reconnect the O7 radio and display receiver assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (TELEPHONE TRANSCEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
a.
C414321C01
1.51,0.219 1.927,0.479 0.417,0.26 1.51,2.521 1.927,2.781 0.417,0.26 1.948,1.552 2.125,0.729 2.125,0.729 2.271,0.729 true 1.49,0.729 1.635,0.729 1.635,0.729 1.833,1.552 true 1.625,3.417 1.854,4.292 1.854,4.292 2,4.292 true 0.094,0.083 0.458,0.365 0.365,0.281 10 false *a 0.083,2.5 0.448,2.802 0.365,0.302 10 false *b 1.594,0.271 1.927,0.479 0.333,0.208 10 false N74 1.635,2.573 1.927,2.781 0.292,0.208 10 false N8 2.333,0.646 2.948,0.844 0.615,0.198 10 false CANN 1.083,0.656 1.698,0.854 0.615,0.198 10 false CANP 2.042,4.208 2.656,4.406 0.615,0.198 10 false CG
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)
*b Front view of DLC3


Disconnect the N74 telephone transceiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N74-15 (CANP) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N74-16 (CANN) - N8-4 (CG)



c.

Reconnect the N74 telephone transceiver assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

13.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)
a.
C414215C02
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.656,0.646 2.438,0.646 2.438,0.646 2.292,1.26 true 2.052,1.49 1.781,2.292 1.781,2.292 1.615,2.292 true 2.74,4.26 2.573,4.26 2.573,4.26 2.323,3.625 true 2.542,2.156 2.323,2.156 2.323,2.156 2.188,1.51 true 1.906,1.49 1.635,2.125 1.635,2.125 1.469,2.125 true 1.573,0.292 2.188,0.49 0.615,0.198 10 false N21 1.542,2.573 2.156,2.771 0.615,0.198 10 false N8 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 1.229,2.219 1.844,2.417 0.615,0.198 10 false CAYL 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 2.698,0.573 3.229,0.781 0.531,0.208 10 false CA3H 2.792,4.188 3.406,4.385 0.615,0.198 10 false BAT 2.646,2.083 3.177,2.292 0.531,0.208 10 false CA3L 1.073,2.052 1.688,2.25 0.615,0.198 10 false CAYH
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the N21 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-6 (CA3H) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N21-21 (CA3L) - N8-16 (BAT)
N21-19 (CAYH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N21-20 (CAYL) - N8-16 (BAT)



c.

Reconnect the N21 central gateway ECU (network gateway ECU) connector.


Result:
Proceed to
OK
NG



OK

NG

14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
14.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N127 No. 7 CAN junction connector.

C414290C20
2.021,0.25 2.427,0.5 0.406,0.25 5.167,0.552 5.573,0.802 0.406,0.25 3.552,1.375 3.365,1.375 3.365,1.375 3.094,1.531 true 3.573,1.99 3.396,1.99 3.396,1.99 3.104,1.844 true 6.219,2.229 6.042,2.229 6.042,2.229 5.906,1.813 true 3.552,1.073 3.365,1.073 3.365,1.073 2.927,1.542 true 3.438,2.208 3.26,2.208 3.26,2.208 2.917,1.833 true 0.135,0.094 0.531,0.365 0.396,0.271 10 false *a 2.063,0.292 2.563,0.531 0.5,0.24 10 false N127 3.594,1.313 4.26,1.552 0.667,0.24 10 false CANH*c 3.604,1.917 4.271,2.156 0.667,0.24 10 false CANL*c 4.292,0.094 4.635,0.406 0.344,0.313 10 false *b 5.281,0.604 5.781,0.844 0.5,0.24 10 false N8 6.26,2.146 6.927,2.385 0.667,0.24 10 false BAT 3.594,0.99 4.26,1.229 0.667,0.24 10 false CANH*c 3.49,2.125 4.156,2.365 0.667,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to Central Gateway ECU (Network Gateway ECU) - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
N127-11 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
N127-22 (CANL) - N8-16 (BAT)
N127-10 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
N127-21 (CANL) - N8-16 (BAT)



c.

Reconnect the N127 No. 7 CAN junction connector.


Result:
Proceed to
OK
NG



OK

15.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

15.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for Radio and Display Type A
except Radio and Display Type B



A

16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

17.CHECK VEHICLE TYPE
16.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the N127 No. 7 CAN junction connector.

C414290C21
2.021,0.25 2.427,0.5 0.406,0.25 5.167,0.552 5.573,0.802 0.406,0.25 6.219,2.229 6.042,2.229 6.042,2.229 5.906,1.813 true 3.219,2.375 3.042,2.375 3.042,2.375 2.74,1.833 true 3.438,0.76 3.25,0.76 3.25,0.76 2.74,1.542 true 0.135,0.094 0.531,0.365 0.396,0.271 10 false *a 2.063,0.292 2.563,0.531 0.5,0.24 10 false N127 3.26,2.302 3.927,2.542 0.667,0.24 10 false CANL*c 4.292,0.094 4.635,0.406 0.344,0.313 10 false *b 5.281,0.604 5.781,0.844 0.5,0.24 10 false N8 6.26,2.146 6.927,2.385 0.667,0.24 10 false BAT 3.479,0.688 4.146,0.927 0.667,0.24 10 false CANH*c
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to Radio and Display Receiver Assembly - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
N127-9 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Radio and display receiver assembly
N127-20 (CANL) - N8-16 (BAT)



c.

Reconnect the N127 No. 7 CAN junction connector.


Result:
Proceed to
OK
NG



OK

17.CHECK VEHICLE TYPE

NG

19.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
17.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Telematics System A
w/o Telematics System B



A

18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - TELEPHONE TRANSCEIVER ASSEMBLY)

B

REPLACE NO. 7 CAN JUNCTION CONNECTOR

18.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the N127 No. 7 CAN junction connector.

C414290C22
2.021,0.25 2.427,0.5 0.406,0.25 5.167,0.552 5.573,0.802 0.406,0.25 6.219,2.229 6.042,2.229 6.042,2.229 5.906,1.813 true 2.99,2.563 2.813,2.563 2.813,2.563 2.563,1.833 true 3.229,0.521 3.042,0.521 3.042,0.521 2.573,1.531 true 0.135,0.094 0.531,0.365 0.396,0.271 10 false *a 2.063,0.292 2.563,0.531 0.5,0.24 10 false N127 4.292,0.094 4.635,0.406 0.344,0.313 10 false *b 5.281,0.604 5.781,0.844 0.5,0.24 10 false N8 6.26,2.146 6.927,2.385 0.667,0.24 10 false BAT 3.031,2.49 3.698,2.729 0.667,0.24 10 false CANL*c 3.281,0.438 3.948,0.677 0.667,0.24 10 false CANH*c
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b Front view of DLC3
*c to Telephone Transceiver Assembly - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
N127-8 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Telephone transceiver assembly
N127-19 (CANL) - N8-16 (BAT)



c.

Reconnect the N127 No. 7 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 7 CAN JUNCTION CONNECTOR

NG

20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (TELEPHONE TRANSCEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
19.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
a.
C414320C02
1.51,0.219 1.927,0.479 0.417,0.26 1.51,2.521 1.927,2.781 0.417,0.26 1.99,1.552 2.167,0.729 2.167,0.729 2.313,0.729 true 1.521,0.729 1.667,0.729 1.667,0.729 1.865,1.552 true 2.354,3.802 2.5,4.292 2.5,4.292 2.646,4.292 true 0.094,0.083 0.458,0.365 0.365,0.281 10 false *a 0.083,2.5 0.448,2.802 0.365,0.302 10 false *b 1.635,0.271 1.927,0.479 0.292,0.208 10 false O7 1.635,2.573 1.927,2.781 0.292,0.208 10 false N8 2.354,0.656 2.969,0.854 0.615,0.198 10 false CANL 1.104,0.656 1.719,0.854 0.615,0.198 10 false CANH 2.698,4.208 3.313,4.406 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of DLC3


Disconnect the O7 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-13 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
O7-14 (CANL) - N8-16 (BAT)



c.

Reconnect the O7 radio and display receiver assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

20.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (TELEPHONE TRANSCEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
a.
C414321C02
1.51,0.219 1.927,0.479 0.417,0.26 1.51,2.521 1.927,2.781 0.417,0.26 1.948,1.552 2.125,0.729 2.125,0.729 2.271,0.729 true 1.49,0.729 1.635,0.729 1.635,0.729 1.833,1.552 true 2.354,3.792 2.49,4.292 2.49,4.292 2.635,4.292 true 0.094,0.083 0.458,0.365 0.365,0.281 10 false *a 0.083,2.5 0.448,2.802 0.365,0.302 10 false *b 1.594,0.271 1.927,0.479 0.333,0.208 10 false N74 1.635,2.573 1.927,2.781 0.292,0.208 10 false N8 2.333,0.646 2.948,0.844 0.615,0.198 10 false CANN 1.083,0.656 1.698,0.854 0.615,0.198 10 false CANP 2.688,4.208 3.302,4.406 0.615,0.198 10 false BAT
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)
*b Front view of DLC3


Disconnect the N74 telephone transceiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N74-15 (CANP) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N74-16 (CANN) - N8-16 (BAT)



c.

Reconnect the N74 telephone transceiver assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

21.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)
a.
C368242C45
1.417,0.24 1.958,0.458 0.542,0.219 2.146,1.104 2.167,0.573 2.167,0.573 1.927,0.573 true 1.51,1.802 1.708,1.802 1.708,1.802 1.875,1.292 true 2.042,1.271 2.229,1.906 2.229,1.906 2.396,1.906 true 1.594,1.99 1.792,1.99 1.792,1.99 1.979,1.271 true 1.573,0.281 2.031,0.479 0.458,0.198 10 false N21 1.542,0.479 2,0.677 0.458,0.198 10 false CA3H 2.427,1.823 2.906,2.021 0.479,0.198 10 false CA3L 0.073,0.052 0.531,0.25 0.458,0.198 10 false *a 1.198,1.906 1.677,2.104 0.479,0.198 10 false CAYL 1.115,1.729 1.594,1.927 0.479,0.198 10 false CAYH
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the N21 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-6 (CA3H) - N21-21 (CA3L) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N21-19 (CAYH) - N21-20 (CAYL)



c.

Reconnect the N21 central gateway ECU (network gateway ECU) connector.


Result:
Proceed to
OK
NG



OK

NG

22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N127 No. 7 CAN junction connector.

C467151C05
0.573,1.24 0.979,1.49 0.406,0.25 5.073,0.719 4.906,0.719 4.906,0.719 4.26,1.438 true 4.813,2.24 4.646,2.24 4.646,2.24 4.281,1.667 true 5.344,1.021 5.177,1.021 5.177,1.021 4.448,1.438 true 5.073,1.99 4.906,1.99 4.906,1.99 4.458,1.667 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.604,1.292 1.104,1.531 0.5,0.24 10 false N127 5.125,0.646 5.792,0.885 0.667,0.24 10 false CANH*b 4.896,2.177 5.563,2.417 0.667,0.24 10 false CANL*b 5.396,0.938 6.063,1.177 0.667,0.24 10 false CANH*b 5.156,1.906 5.823,2.146 0.667,0.24 10 false CANL*b
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
N127-11 (CANH) - N127-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
N127-10 (CANH) - N127-21 (CANL)



c.

Reconnect the N127 No. 7 CAN junction connector.


Result:
Proceed to
OK
NG



OK

23.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

23.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
for Radio and Display Type A
except Radio and Display Type B



A

24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

25.CHECK VEHICLE TYPE
24.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the N127 No. 7 CAN junction connector.

C467151C06
0.573,1.24 0.979,1.49 0.406,0.25 4.833,0.458 4.667,0.458 4.667,0.458 4.125,1.417 true 4.469,2.458 4.302,2.458 4.302,2.458 4.115,1.667 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.604,1.292 1.104,1.531 0.5,0.24 10 false N127 4.906,0.385 5.573,0.625 0.667,0.24 10 false CANH*b 4.531,2.365 5.198,2.604 0.667,0.24 10 false CANL*b
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Radio and Display Receiver Assembly



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
N127-9 (CANH) - N127-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly



c.

Reconnect the N127 No. 7 CAN junction connector.


Result:
Proceed to
OK
NG



OK

25.CHECK VEHICLE TYPE

NG

27.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
25.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Telematics System A
w/o Telematics System B



A

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR - TELEPHONE TRANSCEIVER ASSEMBLY)

B

REPLACE NO. 7 CAN JUNCTION CONNECTOR

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 CAN JUNCTION CONNECTOR - TELEPHONE TRANSCEIVER ASSEMBLY)
a.

Disconnect the N127 No. 7 CAN junction connector.

C467151C07
0.573,1.24 0.979,1.49 0.406,0.25 4.573,0.229 4.406,0.229 4.406,0.229 3.906,1.469 true 4.167,2.635 4,2.635 4,2.635 3.917,1.698 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.604,1.292 1.104,1.531 0.5,0.24 10 false N127 4.656,0.156 5.323,0.396 0.667,0.24 10 false CANH*b 4.208,2.552 4.875,2.792 0.667,0.24 10 false CANL*b
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Telephone Transceiver Assembly



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
N127-8 (CANH) - N127-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Telephone transceiver assembly



c.

Reconnect the N127 No. 7 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 7 CAN JUNCTION CONNECTOR

NG

28.CHECK FOR SHORT IN CAN BUS WIRES (TELEPHONE TRANSCEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
27.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
a.
C369143C36
1.5,0.417 1.917,0.667 0.417,0.25 1.885,2.177 1.583,1.167 1.583,1.167 1.417,1.167 true 2.042,2.167 1.75,1 1.75,1 1.583,1 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.625,0.458 1.938,0.656 0.313,0.198 10 false O7 1.021,1.104 1.51,1.302 0.49,0.198 10 false CANH 1.188,0.938 1.677,1.135 0.49,0.198 10 false CANL
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the O7 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-13 (CANH) - O7-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



c.

Reconnect the O7 radio and display receiver assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

28.CHECK FOR SHORT IN CAN BUS WIRES (TELEPHONE TRANSCEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)
a.
C369145C42
1.5,0.667 1.917,0.917 0.417,0.25 1.958,2.115 2.167,1.417 2.167,1.417 2.333,1.417 true 1.813,2.104 2,1.25 2,1.25 2.167,1.25 true 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.604,0.698 2.094,0.906 0.49,0.208 10 false N74 2.219,1.188 2.688,1.406 0.469,0.219 10 false CANP 2.375,1.354 2.844,1.573 0.469,0.219 10 false CANN
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)


Disconnect the N74 telephone transceiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N74-15 (CANP) - N74-16 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



c.

Reconnect the N74 telephone transceiver assembly connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - NO. 7 CAN JUNCTION CONNECTOR)

29.CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N127 No. 7 CAN junction connector.

C467151C05
0.573,1.24 0.979,1.49 0.406,0.25 5.073,0.719 4.906,0.719 4.906,0.719 4.26,1.438 true 4.813,2.24 4.646,2.24 4.646,2.24 4.281,1.667 true 5.344,1.021 5.177,1.021 5.177,1.021 4.448,1.438 true 5.073,1.99 4.906,1.99 4.906,1.99 4.458,1.667 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.604,1.292 1.104,1.531 0.5,0.24 10 false N127 5.125,0.646 5.792,0.885 0.667,0.24 10 false CANH*b 4.896,2.177 5.563,2.417 0.667,0.24 10 false CANL*b 5.396,0.938 6.063,1.177 0.667,0.24 10 false CANH*b 5.156,1.906 5.823,2.146 0.667,0.24 10 false CANL*b
*a Front view of wire harness connector
(to No. 7 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
N127-11 (CANH) - N127-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
N127-10 (CANH) - N127-21 (CANL)



c.

Reconnect the N127 No. 7 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 7 CAN JUNCTION CONNECTOR

NG

30.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)
30.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)
a.

Disconnect the N127 No. 7 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-6 (CA3H) - N127-11 (CANH) Cable disconnected from negative (-) battery terminal Below 1 Ω
N21-21 (CA3L) - N127-22 (CANL)
N21-19 (CAYH) - N21-10 (CANH) Cable disconnected from negative (-) battery terminal Below 1 Ω
N21-20 (CAYL) - N127-21 (CANL)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 7 CAN JUNCTION CONNECTOR)