Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › DIESEL THROTTLE BODY › from 2021.07
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0387389 DIESEL THROTTLE BODY A

1GD-FTV ENGINE CONTROL  DIESEL THROTTLE BODY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the diesel throttle body assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Replacement of diesel throttle body assembly Perform initialization - w/ DPF:
(Click here)
for Water Cooled Type Intercooler:
(Click here)
w/ EGR Cooler:
(Click here)
w/o EGR Cooler:
(Click here)

PROCEDURE

Hide 12601B 1.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

for Air Cooled Type Intercooler:

i.
A443253

Remove the 2 nuts from the No. 1 engine cover bracket and No. 2 engine cover bracket.


ii.

Detach the 2 clips and No. 1 engine cover sub-assembly from the No. 2 water by-pass pipe.

NOTICE:

Make sure to lift the No. 1 engine cover sub-assembly upward. Pulling the No. 1 engine cover sub-assembly towards you may damage the No. 1 engine cover sub-assembly.




b.

for Water cooled Type Intercooler:

i.
A453818

Detach the 4 clips and No. 1 engine cover sub-assembly.



Hide 51406A 2.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 52618 3.REMOVE LOWER FRONT BUMPER ABSORBER

Hide 51405A 4.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 25761B 5.DISCONNECT NO. 1 VACUUM TRANSMITTING HOSE (for Air Cooled Type Intercooler)

Hide 17303T 6.REMOVE AIR PIPE SUB-ASSEMBLY (for Air Cooled Type Intercooler)

Hide 17030 7.REMOVE AIR HOSE ASSEMBLY (for Water Cooled Type Intercooler)

a.
A457086C01
1.063,3.646 1.302,3.417 1.302,3.417 1.573,3.417 true 1.667,3.333 1.979,3.531 0.313,0.198 10 false *a
*a Retainer


Release the 2 retainers and disconnect the No. 2 air tube assembly from the intake air connector and intercooler assembly as shown in the illustration.


Hide 26100G 8.REMOVE DIESEL THROTTLE BODY ASSEMBLY

a.

for Air Cooled Type Intercooler:

i.
A443560

Disconnect the intake air temperature sensor connector.


ii.
A443550

Remove the bolt and disconnect the fuel hose bracket from the diesel throttle body assembly.


iii.
A443551

for Cold Area Specification Vehicles:

Slide the 2 clips and disconnect the No. 11 water by-pass hose and No. 14 water by-pass hose from the diesel throttle body assembly.


iv.
A443552

Disconnect the connector and clamp.


v.

Remove the 4 bolts, intake air connector, diesel throttle body assembly and 2 gaskets.


vi.
A443553

Disconnect the connector to remove the emission control valve wire from the diesel throttle body assembly.



b.

for Water cooled Type Intercooler:

i.
A453820

Disconnect the connector from the intake air temperature sensor.


ii.
A453821

Remove the bolt and disconnect the fuel hose bracket from the diesel throttle body assembly.


iii.
A453822C02
0.667,1.75 0.917,1.75 0.917,1.75 1.188,1.396 true 2.125,1.083 2.583,1.5 2.583,1.5 2.75,1.5 true 2.854,1.417 3.167,1.615 0.313,0.198 10 true *2 0.521,1.667 0.833,1.865 0.313,0.198 10 true *1
*1 No. 11 Water by-pass Hose
*2 No. 14 Water by-pass Hose


Slide the 2 clips and disconnect the No. 11 water by-pass hose and No. 14 water by-pass hose from the diesel throttle body assembly.


iv.
A453823

Remove the 4 bolts, intake air connector, diesel throttle body assembly and 2 gaskets.


v.
A435770

Disconnect the emission control valve wire connector from the diesel throttle body assembly.