Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2021.07
RM35X0E _51 Engine / Hybrid System _079219 1GD-FTV ENGINE MECHANICAL _0384428 ENGINE ASSEMBLY A

1GD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of ECM
·

Learning Values Save

·

Learning Values Write

·

Perform Vehicle Identification Number (VIN) or frame number registration


DTC P063051 is stored
·

w/ DPF:

(Click here)

·

for Water Cooled Type Intercooler:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)


ECU communication ID registration Engine start function See the Service Bulletin for the registration method.
for RC60J:

Performing iMT installation information reset


·

iMT system

·

DTCs are output


(Click here)
Replacement of engine assembly Clear crank time compensation data Engine starting
·

w/ DPF:

(Click here)

·

for Water Cooled Type Intercooler:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)


·

Input injector compensation code

·

Pilot quantity learning


Engine starting
·

w/ DPF:

(Click here)

·

for Water Cooled Type Intercooler:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)


Replacement of crankshaft position sensor plate Clear crank time compensation data Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data
·

w/ DPF:

(Click here)

·

for Water Cooled Type Intercooler:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)


w/ DPF:

Replacement of air fuel ratio sensor


Clear A/F sensor learning value data - (Click here)
w/ DPF, for Water Cooled Type Intercooler:

Replacement of exhaust manifold converter sub-assembly


Clear DPF thermal deterioration data -
·

w/ DPF:

(Click here)

·

for Water Cooled Type Intercooler:

(Click here)


Replacement of injector assembly
·

Injector compensation code registration

·

Pilot quantity learning


Engine starting
·

w/ DPF:

(Click here)

·

for Water Cooled Type Intercooler:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)


·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly

·

Replacement of turbocharger nozzle vane control actuator


Perform initialization -
·

w/ DPF:

(Click here)

·

for Water Cooled Type Intercooler:

(Click here)

·

w/ EGR Cooler:

(Click here)

·

w/o EGR Cooler:

(Click here)


w/ Stop and Start System:

Replacement of starter assembly

NOTICE:

When the starter assembly is replaced, "STARTER relay" and "STARTER NO.2 relay" must be also replaced.



Clear the number of starter operations Stop and start system (Click here)
w/ Stop and Start System:
·

Replacement of flywheel sub-assembly (for Automatic Transmission)

·

Replacement of flywheel with damper assembly (for Manual Transmission)


Total number of engine starts reset
for AE60E:

Replacement of automatic transmission assembly


Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
for AE60E:

Replacement of automatic transmission fluid


ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc. Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative when not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative when not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly may fall off the engine lifter.

·
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.REMOVE FRONT WHEELS

Hide 51406A 6.REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ No. 2 Engine Under Cover Sub-assembly)

a.
A443611

Remove the 6 clips, 7 bolts and No. 2 engine under cover sub-assembly.


Hide 52618 7.REMOVE LOWER FRONT BUMPER ABSORBER

a.
A443610C01
0,0 0,0 false
V100135

Bolt
V100136

Screw


Remove the 4 bolts, 4 screws and 4 clips.


b.

Detach the 2 guides and remove the lower front bumper absorber.


Hide 51405A 8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A443699

w/ No. 2 Engine Under Cover Sub-assembly:

i.

Remove the 10 clips.


ii.

Detach the guide and remove the No. 1 engine under cover sub-assembly.



b.
A443613

w/o No. 2 Engine Under Cover Sub-assembly:

i.

Remove the 12 clips and 2 bolts.


ii.

Detach the guide and remove the No. 1 engine under cover sub-assembly.



Hide 51495 9.REMOVE TRANSMISSION UNDER COVER (w/ Cover)

Hide 51408B 10.REMOVE ENGINE UNDER COVER SUB-ASSEMBLY RH (w/ Cover)

a.
A443330

Remove the 6 bolts and engine under cover sub-assembly RH.


Hide 51773E 11.REMOVE STEP PLATE COVER RH (w/ Cover)

a.
A443964C02
0.813,0.823 1.031,1.031 0.219,0.208 10 true *A 1.094,0.823 1.313,1.031 0.219,0.208 10 true *B
*A for Automatic Transmission
*B for Manual Transmission


Remove the 4 clips, 5 bolts and step plate cover RH.


Hide 13.DRAIN ENGINE COOLANT

Hide 15.DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)

Hide 16.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 18.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)

Hide 85110 19.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 55701J 20.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

a.
A443608C01
0.042,0.031 0.281,0.25 0.24,0.219 10 true *A 0.042,2.385 0.302,2.615 0.26,0.229 10 false *B
*A for LHD
*B for RHD


for LH Side:

i.

Detach the 2 claws and remove the No. 2 heater air duct splash shield seal from the outer cowl top panel sub-assembly.



b.
A443607C01
0.042,0.031 0.281,0.271 0.24,0.24 10 false *A 0.063,2.385 0.281,2.594 0.219,0.208 10 false *B
*A for LHD
*B for RHD


for RH Side:

i.

Detach the 2 claws and remove the No. 2 heater air duct splash shield seal from the outer cowl top panel sub-assembly.



c.
A442624C01
0.083,0.115 0.333,0.292 0.25,0.177 10 true *A 0.104,2.646 0.354,2.813 0.25,0.167 10 true *B
*A for LHD
*B for RHD


Disconnect the connector from the front wiper deicer wire harness.


d.

Detach the 4 clamps and disconnect the engine room main wire from the outer cowl top panel sub-assembly.


e.
A442625

for LHD:

i.

Disconnect the connector from the brake master cylinder reservoir assembly.


ii.

Detach the 2 clamps and disconnect the engine room main wire from the outer cowl top panel sub-assembly.



f.
A442626

for RHD:

i.

Disconnect the connector from the brake master cylinder reservoir assembly.


ii.

Detach the 4 clamps and disconnect the engine room main wire from the outer cowl top panel sub-assembly.



g.
A443358C01
0.104,0.104 0.375,0.292 0.271,0.188 10 true *A 0.115,2.615 0.375,2.792 0.26,0.177 10 true *B
*A for LHD
*B for RHD


Remove the 2 bolts and disconnect the brake master cylinder reservoir assembly from the outer cowl top panel sub-assembly.


h.
A442627C01
0.073,0.094 0.323,0.26 0.25,0.167 10 true *A 0.083,2.594 0.344,2.75 0.26,0.156 10 true *B
*A for LHD
*B for RHD


Remove the 10 bolts and outer cowl top panel sub-assembly from the body.


Hide 12601B 21.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16551C 22.DISCONNECT NO. 1 INTERCOOLER COOLING WATER HOSE (for Water Cooled Type Intercooler)

Hide 23.REMOVE NO. 2 INTERCOOLER COOLING WATER PIPE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 17360E 24.REMOVE NO. 1 AIR TUBE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 17030 25.REMOVE AIR HOSE ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16278 26.REMOVE NO. 2 WATER BY-PASS PIPE (for Water Cooled Type Intercooler)

Hide 17940D 27.REMOVE INTERCOOLER ASSEMBLY (for Water Cooled Type Intercooler)

Hide 16400 28.REMOVE RADIATOR ASSEMBLY

Hide 12601B 29.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Cover)

Hide 82121 30.DISCONNECT ENGINE WIRE

a.
A442643C01
0.094,0.094 0.344,0.26 0.25,0.167 10 true *A 0.135,2.542 0.385,2.698 0.25,0.156 10 true *B
*A for LHD
*B for RHD


Disconnect the 4 connectors from the ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL


b.
A442644C01
0.083,0.125 0.323,0.292 0.24,0.167 10 true *A 0.167,2.594 0.396,2.75 0.229,0.156 10 true *B
*A for LHD
*B for RHD


Disconnect the 2 connectors from the instrument panel wire.


c.
A442645

for LHD:

Detach the 2 clamps and grommet, and pull out the engine wire from the bracket.


d.
A442646

for RHD:

Detach the clamp and grommet, and pull out the engine wire from the bracket.


Hide 31.REMOVE AIR CLEANER CAP SUB-ASSEMBLY AND AIR CLEANER HOSE

Hide 17801 32.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 25760F 33.REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY

Hide 17303T 34.REMOVE AIR PIPE SUB-ASSEMBLY (for Air Cooled Type Intercooler)

Hide 23941 35.DISCONNECT NO. 1 FUEL FILTER PROTECTOR

Hide 23271H 36.DISCONNECT NO. 1 FUEL HOSE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A442647

Remove the bolt and disconnect the No. 1 fuel hose from the diesel throttle body assembly.


b.

Slide the clamp and disconnect the No. 1 fuel hose from the No. 2 fuel pipe.


Hide 23273H 37.DISCONNECT NO. 2 FUEL HOSE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A442648

Slide the clamp and disconnect the No. 2 fuel hose from the No. 3 nozzle leakage pipe assembly.


Hide 89463C 38.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Nitrogen Oxides Sensor)

a.
A444700

Disconnect the connector from the No. 1 nitrogen oxides sensor.


b.

Remove the 2 bolts and disconnect the No. 1 nitrogen oxides sensor from the body.


Hide 39.DISCONNECT WIRE HARNESS

a.
A442649

Detach the 2 claws and remove the upper No. 1 relay block cover from the No. 1 engine room relay block.


b.
A442650

Remove the 2 bolts and disconnect the wire harness from the body.


c.

Detach the clamp and disconnect the wire harness from the No. 1 engine room relay block.


d.
A442651

Detach the claw and remove the relay block cover from the No. 1 engine room relay block.


e.
A442652

Remove the 2 bolts and disconnect the 2 wire harnesses from the No. 1 engine room relay block.


f.
A442653

Detach the claw and clamp and disconnect the wire harness.


g.
A442654

Detach the claw and 3 connectors from the No. 1 engine room relay block.


Hide 40.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Heater)

Hide 44310 41.DISCONNECT VANE PUMP ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A443337

Remove the 2 bolts and disconnect the vane pump assembly from the generator bracket.


Hide 27020 42.REMOVE GENERATOR ASSEMBLY

Hide 53287B 43.REMOVE RADIATOR SUPPORT EXTENSION RH (for RHD)

a.
A442656

Detach the 2 claws and remove the radiator support extension RH from the body.


Hide 53288B 44.REMOVE RADIATOR SUPPORT EXTENSION LH

a.
A442657

Detach the 2 claws and remove the radiator support extension LH from the body.


Hide 44402 45.DISCONNECT NO. 1 POWER STEERING OIL COOLER SUB-ASSEMBLY

a.
A442658

for RHD:

Remove the bolt and disconnect the return tube sub-assembly.


b.
A442659

Remove the bolt and disconnect the return tube sub-assembly.


c.
A442660C01
0.094,0.094 0.365,0.25 0.271,0.156 10 true *A 0.135,2.49 0.375,2.656 0.24,0.167 10 true *B
*A for LHD
*B for RHD


Remove the 2 bolts and disconnect the No. 1 power steering oil cooler sub-assembly.


Hide 88703 46.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

a.
A442662

Remove the bolt and disconnect the discharge hose sub-assembly from the cooler compressor assembly.


b.

Remove the O-ring from the discharge hose sub-assembly.


Hide 88704 47.REMOVE SUCTION HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

a.
A442663

Remove the bolt and disconnect the suction hose sub-assembly from the cooler compressor assembly.


b.
A442664

Remove the nut and disconnect the suction hose sub-assembly.


c.
A442665

w/o Viscous Heater:

Remove the 2 bolts and suction hose sub-assembly from the water inlet and timing chain cover.


d.

w/ Viscous Heater:

Remove the 2 bolts and suction hose sub-assembly from the No. 1 viscous heater bracket sub-assembly and timing chain cover.


e.

Remove the 2 O-rings from the suction hose sub-assembly.


Hide 44773F 48.DISCONNECT UNION TO CHECK VALVE HOSE

a.
A442666

Slide the clamp and disconnect the union to check valve hose from the vacuum pump assembly.


Hide 49.DISCONNECT INTERMEDIATE SHAFT ASSEMBLY

Hide 89543 50.DISCONNECT FRONT SPEED SENSOR LH

Hide 89542 51.DISCONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 45047 52.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 53.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 54.DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

Hide 55.DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43512 56.REMOVE FRONT DISC

Hide 48069 57.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 58.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 59.REMOVE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 60.REMOVE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 61.REMOVE FRONT AXLE ASSEMBLY LH

Hide 62.REMOVE FRONT AXLE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 51445 63.REMOVE ENGINE UNDER COVER BRACKET

a.
A442668

Remove the 2 bolts and engine under cover bracket from the front frame assembly.


Hide 64.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)

a.
A346693

Remove the bolt and disconnect the water hose sub-assembly from the water inlet.


b.
A346692

Slide the 4 clamps and remove the water hose sub-assembly from the viscous heater with magnet clutch assembly, No. 2 water pipe and water outlet sub-assembly.


Hide 87120G 65.REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)

a.

Disconnect the connector from the viscous heater with magnet clutch assembly.


b.
A346694

Remove the 2 bolts, nut and viscous heater with magnet clutch assembly from the No. 1 viscous heater bracket.


Hide 17410 66.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 37100 67.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 77840A 68.DISCONNECT UREA TUBE WITH HEATER ASSEMBLY (w/ Urea SCR System)

a.
A453121

for Wagon:

i.

Detach the 2 clamps and disconnect the urea tube with heater assembly from the lower center front suspension brace and front frame assembly.



b.
A453123

except Wagon:

i.

Detach the 2 clamps and disconnect the urea tube with heater assembly from the No. 2 engine under cover bracket and front frame assembly.



Hide 53689 69.REMOVE CENTER LOWER FRONT SUSPENSION BRACE (for Wagon)

a.
A453122

Remove the 5 bolts and center lower front suspension brace.


Hide 33030 70.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

Hide 32101A 71.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for Automatic Transmission)

Hide 35000 72.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 31210 73.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 74.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 13450 75.REMOVE FLYWHEEL WITH DAMPER ASSEMBLY (for Manual Transmission)

a.

w/ Viscous Heater:

Remove the viscous heater crankshaft pulley.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>FRONT CRANKSHAFT OIL SEAL>REMOVAL


b.
A349457N01
1.208,0.906 0.521,1.406 0.521,1.406 0.406,1.406 true 1.917,1.031 2.635,1.406 2.635,1.406 2.771,1.406 true 0.125,1.313 0.479,1.5 0.354,0.188 10 false SST 2.802,1.313 3.156,1.5 0.354,0.188 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  (91551-80840)
09330-00021  


c.
A444761

Remove the 8 bolts and flywheel with damper assembly from the crankshaft.


Hide 13405 76.REMOVE FLYWHEEL SUB-ASSEMBLY (for Automatic Transmission)

a.

w/ Viscous Heater:

Remove the viscous heater crankshaft pulley.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>FRONT CRANKSHAFT OIL SEAL>REMOVAL



c.
A349457N01
1.208,0.906 0.521,1.406 0.521,1.406 0.406,1.406 true 1.917,1.031 2.635,1.406 2.635,1.406 2.771,1.406 true 0.125,1.313 0.479,1.5 0.354,0.188 10 false SST 2.802,1.313 3.156,1.5 0.354,0.188 10 false SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  (91551-80840)
09330-00021  


d.
A344484

Remove the 8 bolts, rear drive plate spacer, pump impeller drive plate and flywheel sub-assembly from the crankshaft.


Hide 11355 77.REMOVE REAR END PLATE

a.
A340241

Remove the bolt and rear end plate from the cylinder block sub-assembly.


Hide 51108C 78.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

a.
A442669

Remove the 4 bolts and rear side rail reinforcement sub-assembly LH.


Hide 51107D 79.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

a.
A442670

Remove the 4 bolts and rear side rail reinforcement sub-assembly RH.


Hide 80.REMOVE ENGINE ASSEMBLY

a.
A444774C01
0,0 0,0 false
V113146

Place Wooden Block or Plate Attachments


Set the engine assembly on an engine lifter.

NOTICE:
·

Place wooden blocks or plate lift attachments so that the engine assembly is level.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.

·

Never install attachments to the oil pan of the engine assembly as doing so may deform the oil pan.




b.
A442671

Remove the 6 bolts and 2 nuts shown in the illustration.


c.

Operate the engine lifter and slowly remove the engine assembly with front frame assembly from the vehicle.

NOTICE:
·

Make sure that the engine assembly is clear of all wiring and hoses.

·

While lowering the engine assembly from the vehicle, do not allow it to contact the vehicle.




d.
A442672

Slide the clamp and disconnect the hose.


Hide 81.INSTALL ENGINE HANGER

a.
A343930C01
0.5,0.833 0.667,0.333 0.667,0.333 0.75,0.333 true 2.417,0.479 2.667,0.229 2.667,0.229 2.75,0.229 true 0.781,0.229 1.094,0.385 0.313,0.156 10 false *1 2.781,0.135 3.094,0.292 0.313,0.156 10 false *2
*1 Upper No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the upper No. 1 engine hanger and No. 2 engine hanger with the 3 bolts as shown in the illustration.

Torque:
for upper No. 1 engine hanger : 29 N*m (296 kgf*cm, 21 ft.*lbf)
for No. 2 engine hanger : 26 N*m (265 kgf*cm, 19 ft.*lbf)

HINT:
Upper No. 1 Engine Hanger 12284-11010
No. 2 Engine Hanger 12282-11080
Bolt 91552-81025 and 91671-80835



b.

Attach an engine sling device and hang the engine assembly with a chain block.


Hide 51100H 82.REMOVE FRONT FRAME ASSEMBLY

a.
A442673C01
0.073,0.104 0.323,0.271 0.25,0.167 10 true *a 0.125,2.563 0.354,2.74 0.229,0.177 10 true *b
*a LH Side
*b RH Side


Remove the 4 bolts and disconnect the front frame assembly from the engine assembly.


Hide 12391 83.REMOVE FRONT ENGINE MOUNTING INSULATOR RH

a.
A442674

Remove the nut and front engine mounting insulator RH from the front engine mounting insulator.


Hide 12362A 84.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A442675C01
0.083,0.115 0.302,0.281 0.219,0.167 10 true *a 0.125,2.583 0.375,2.75 0.25,0.167 10 true *b
*a LH Side
*b RH Side


Remove the 2 nuts and 2 front engine mounting insulators from the 2 front engine mounting brackets.


Hide 85.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.



a.

Install the engine assembly to the engine stand with the bolts.


b.

Remove the 3 bolts, upper No. 1 engine hanger and No. 2 engine hanger.


Hide 82121 86.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine assembly.