In this circuit, the combination meter assembly receives engine speed signals from the ECM via CAN communication. The combination meter assembly displays the engine speed calculated based on the data received from the ECM.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Before replacing the ECM, refer to the Service Bulletin.
Using the GTS, read the Data List.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine RPM | Engine speed | Min.: 0 rpm, Max.: 12750 rpm | Actual engine speed | - |
| Tester Display |
|---|
| Engine RPM |
When the Data List values of the ECUs match, an internal malfunction of the ECM is suspected.
When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.
The Data List values of the ECUs do not match.
| Proceed to |
|---|
| OK |
| NG (for 7GR-FKS) |
| NG (for 1GD-FTV) |
OK
NG (for 7GR-FKS)
NG (for 1GD-FTV)
Check if SFI system DTCs are output.
Click hereEngine / Hybrid System>7GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, read the Data List.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine RPM | Engine speed | Min.: 0 rpm, Max.: 12750 rpm | Actual engine speed | - |
| Tester Display |
|---|
| Engine RPM |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | Actual engine speed | - |
| Tester Display |
|---|
| Engine Speed |
When the Data List values of the ECUs match, an internal malfunction of the ECM is suspected.
When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.
The Data List values of the ECUs do not match.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if ECD system DTCs are output.
w/ DPF: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR
w/ EGR Cooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>DTC CHECK / CLEAR
w/o EGR Cooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>DTC CHECK / CLEAR
for Water Cooled Type Intercooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>DTC CHECK / CLEAR
| Proceed to |
|---|
| OK |
| NG |
OK
NG
w/ DPF: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DIAGNOSTIC TROUBLE CODE CHART
w/ EGR Cooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>DIAGNOSTIC TROUBLE CODE CHART
w/o EGR Cooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o EGR Cooler)>DIAGNOSTIC TROUBLE CODE CHART
for Water Cooled Type Intercooler: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>DIAGNOSTIC TROUBLE CODE CHART
Using the GTS, read the Data List.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine RPM | Engine speed | Min.: 0 rpm, Max.: 12750 rpm | Actual engine speed | - |
| Tester Display |
|---|
| Engine RPM |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | Actual engine speed | - |
| Tester Display |
|---|
| Engine Speed |
When the Data List values of the ECUs match, an internal malfunction of the ECM is suspected.
When the Data List values of the ECUs do not match, a signal output error of the ECM or an internal malfunction of the combination meter assembly is suspected.
The Data List values of the ECUs do not match.
| Proceed to |
|---|
| OK |
| NG |
OK
NG