Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EGR VALVE (w/o EGR Cooler) › from 2021.07
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0389335 EGR VALVE(w/o EGR Cooler) A

1GD-FTV EMISSION CONTROL  EGR VALVE(w/o EGR Cooler)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the EGR valve removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
·

Replacement of diesel throttle body assembly

·

Replacement of electric EGR control valve assembly


Perform initialization - (Click here)

CAUTION:
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

Hide 85110 2.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 55701J 3.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 26100G 4.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 87209 5.REMOVE WATER HOSE SUB-ASSEMBLY (w/ Heater)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.

w/ Rear Heater:

i.
A443316

Slide the 2 clamps and disconnect the 2 water hose sub-assemblies from the water pipe.


ii.

Slide the 4 clamps and remove the 2 water hose sub-assemblies from the air conditioning unit assembly and No. 2 water by-pass pipe.



b.
A443317

w/o Rear Heater:

Slide the 4 clamps and remove the 2 water hose sub-assemblies from the air conditioning unit assembly and No. 2 water by-pass pipe.


Hide 16278 6.REMOVE NO. 2 WATER BY-PASS PIPE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A444775C01
0.104,0.146 0.354,0.323 0.25,0.177 10 true *A 0.146,2.5 0.406,2.656 0.26,0.156 10 true *B
*A w/ Heater
*B w/o Heater


for Laminated EGR Pre-cooler:

Detach the clamp, slide the clamp and disconnect the No. 18 water by-pass hose from the EGR pipe with cooler sub-assembly.


b.
A440924C01
0.083,0.083 0.323,0.24 0.24,0.156 10 true *A 0.104,2.667 0.365,2.844 0.26,0.177 10 true *B
*A w/ Heater
*B w/o Heater


w/ Viscous Heater:

Slide the clamp and disconnect the water by-pass hose sub-assembly from the No. 2 water by-pass pipe.


c.

w/ Heater:

Slide the clamp and disconnect the No. 13 water by-pass hose from the No. 2 water by-pass pipe.


d.

Slide the clamp and disconnect the No. 15 water by-pass hose from the water by-pass pipe.


e.

Slide the clamp and disconnect the No. 16 water by-pass hose from the EGR pipe stay.


f.
A440925C01
0.073,0.104 0.313,0.292 0.24,0.188 10 true *A 0.115,2.646 0.375,2.823 0.26,0.177 10 true *B
*A w/ Heater
*B w/o Heater


Remove the 3 bolts and No. 2 water by-pass pipe from the cylinder head cover sub-assembly and No. 3 water by-pass pipe sub-assembly.


Hide 89421C 7.REMOVE DIESEL TURBO PRESSURE SENSOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A493092

Disconnect the connector from the diesel turbo pressure sensor.


b.

Slide the clip and disconnect the vacuum hose from the diesel turbo pressure sensor.


c.

Remove the bolt and diesel turbo pressure sensor from the No. 3 water by-pass pipe sub-assembly.


Hide 23265C 8.REMOVE GAS FILTER

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A443319

Disconnect the vacuum hose from the intake manifold.


b.

Detach the clamp and remove the gas filter from the gas filter bracket.


Hide 12632 9.REMOVE NO. 2 ENGINE COVER BRACKET

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A443320

Remove the 2 bolts and No. 2 engine cover bracket from the No. 3 water by-pass pipe sub-assembly and EGR valve adapter sub-assembly.


Hide 23941 10.DISCONNECT NO. 1 FUEL FILTER PROTECTOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440928

Disconnect the connector from the fuel filter assembly.


b.
A440929

Detach the clamp and disconnect the wire harness from the No. 1 fuel filter protector.


c.
A440930

Remove the bolt and disconnect the No. 1 fuel filter protector from the body.


Hide 82121 11.DISCONNECT ENGINE WIRE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440931

Disconnect the 2 connectors from the turbocharger sub-assembly.


b.
A440932

Detach the clamp and disconnect the connector from the intake mass air flow meter sub-assembly.


c.
A443321

Disconnect the connector from the camshaft position sensor.


d.
A443322

Detach the 3 clamps and disconnect the engine wire from the 2 wire harness clamp brackets.


e.
A443323

Disconnect the 4 connectors from the 4 injector assemblies.


f.
A440938

Disconnect the connector from the electric EGR control valve assembly.


g.

Disconnect the connector from the glow plug connector.


h.
A443324

Remove the bolt and disconnect the connector from the sensor wire of the common rail assembly.


i.
A493093

Disconnect the connector from the vane pump assembly.


j.
A443326

Detach the 2 clamps and disconnect the engine wire from the No. 3 water by-pass pipe sub-assembly and wire harness clamp bracket.


k.
A443327

Detach the clamp, remove the bolt and disconnect the engine wire from the No. 4 water by-pass pipe sub-assembly.


Hide 25625 12.REMOVE EGR VALVE BRACKET

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A343894

Remove the bolt, nut and EGR valve bracket from the electric EGR control valve assembly and intake manifold.


Hide 25612 13.REMOVE NO. 2 EGR PIPE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A443328

Remove the bolt, 4 nuts and No. 2 EGR pipe from the electric EGR control valve assembly and intake manifold.


b.

Remove the 2 gaskets.


Hide 25800 14.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A440945

Detach the clamp and disconnect the connector from the common rail assembly.


b.
A443329

Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.


c.

Remove the 2 bolts and electric EGR control valve assembly from the EGR valve adapter sub-assembly.


d.

Remove the gasket.