2007-2013 Highlander Kluger · Service Manual ENGINE

REPLACEMENT

Removal / installation · Vehicles built from May 2007


1. REPLACE INTAKE VALVE GUIDE BUSH
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A121839E02
    Using SST and a hammer, tap out the intake valve guide bushes.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

  1. A109626
    Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head.

    Cylinder bore diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)

    Select a new guide bush (STD or O/S 0.05):
    Bush size
    Bush bore diameter
    STD
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    O/S 0.05
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.
    If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A120710E04
    Using SST, tap in new intake valve guide bushes to the specified protrusion height.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    9.30 to 9.70 mm (0.3661 to 0.3819 in.)

  1. A131839
    Using a sharp 5.5 mm reamer, ream the valve guide bushings to obtain the specified clearance.

    Standard oil clearance:
    0.025 to 0.060 mm (0.0010 to 0.0023 in.)


2. REPLACE EXHAUST VALVE GUIDE BUSH
  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. Using SST and hammer, tap out the exhaust valve guide bushes.

    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

  1. A109628
    Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head.

    Cylinder bore diameter:
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)

    Select a new guide bush (STD or O/S 0.05):
    Bush size
    Bush bore diameter
    STD
    10.285 to 10.306 mm (0.4049 to 0.4057 in.)
    O/S 0.05
    10.335 to 10.356 mm (0.4069 to 0.4077 in.)

    If the bush bore diameter of the cylinder head is greater than 10.306 mm (0.4057 in.), machine the bush bore to the dimension of 10.335 to 10.356 mm (0.4069 to 0.4077 in.) to install an O/S 0.05 valve guide bush.
    If the bush bore diameter of the cylinder head is greater than 10.356 mm (0.4077 in.), replace the cylinder head.

  1. Heat the cylinder head to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head on wooden blocks.

  1. A120712E04
    Using SST, tap in new exhaust valve guide bushes to the specified protrusion height.
    SST
    09201-10000   (09201-01050)
    09950-70010   (09951-07100)

    Protrusion height:
    9.30 to 9.70 mm (0.3661 to 0.3819 in.)

  1. A096429
    Using a sharp 5.5 mm reamer, ream the valve guide bushings to obtain the specified clearance.

    Standard oil clearance:
    0.030 to 0.065 mm (0.0012 to 0.0026 in.)


3. REPLACE RING PIN

NOTICE:
It is not necessary to remove the ring pin unless it is being replaced.

  1. A131888E04
    Using a plastic hammer, tap in new ring pins to the specified protrusion height.

    Specified protrusion height:
    2.5 to 3.5 mm (0.098 to 0.138 in.)


4. REPLACE STUD BOLT

NOTICE:
If the stud bolt is deformed or the threads are damaged, replace it.

  1. Using E6 and E8 "TORX" sockets, install the stud bolts.

    A134987E01

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for bolts A and B
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf } for bolt C


5. REPLACE STRAIGHT PIN

NOTICE:
If the straight pin is deformed, replace it.

  1. Using a plastic hammer, tap in new straight pins as shown in the illustration.

    A131890E04

    Protrusion height:
    17.5 to 19.5 mm (0.689 to 0.768 in.)

← INSPECTION (from May 2007)REASSEMBLY (from May 2007) →