INSPECTION
Inspection · Vehicles built from May 2007
| INSPECT CYLINDER HEAD SUB-ASSEMBLY |
Using a precision straight edge and feeler gauge, measure the warpage of the contact surface of the cylinder block sub-assembly and manifolds.

- Standard warpage:
Item
Warpage
Cylinder head lower
0.05 mm (0.0020 in.)
Intake
0.08 mm (0.0031 in.)
Exhaust
0.08 mm (0.0031 in.)
- Maximum warpage:
Item
Warpage
Cylinder head lower
0.10 mm (0.0039 in.)
Intake
0.10 mm (0.0039 in.)
Exhaust
0.10 mm (0.0039 in.)
| INSPECT CYLINDER HEAD FOR CRACKS |
Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.

If cracked, replace the cylinder head sub-assembly.
| INSPECT INTAKE VALVE |
Using a micrometer, measure the diameter of the valve stem.

- Valve stem diameter:
- 5.470 to 5.485 mm (0.2154 to 0.2159 in.)
Using vernier calipers, measure the valve head margin thickness.

- Standard margin thickness:
- 1.0 mm (0.039 in.)
- Minimum margin thickness:
- 0.5 mm (0.0197 in.)
Using vernier calipers, measure the valve's overall length.

- Standard overall length:
- 105.85 mm (4.1673 in.)
- Minimum overall length:
- 105.35 mm (4.1476 in.)
| INSPECT EXHAUST VALVE |
Using a micrometer, measure the diameter of the valve stem.

- Valve stem diameter:
- 5.465 to 5.480 mm (0.2151 to 0.2157 in.)
Using vernier calipers, measure the valve head margin thickness.

- Standard margin thickness:
- 1.0 mm (0.039 in.)
- Minimum margin thickness:
- 0.5 mm (0.0197 in.)
Using vernier calipers, measure the valve's overall length.

- Standard overall length:
- 110.40 mm (4.3464 in.)
- Minimum overall length:
- 109.90 mm (4.3268 in.)
| INSPECT INTAKE VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Check the valve face and valve spring seat by using the following procedure:

If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.
If Prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve spring seat.
Check that the valve spring seat contacts in the middle of the valve face with the width between 1.1 and 1.5 mm (0.043 and 0.059 in.).
| INSPECT EXHAUST VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve spring seat.
Check the valve face and valve spring seat by using the following procedure:

If Prussian blue appears around the entire valve face, the valve face is concentric. If not, replace the valve.
If Prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve spring seat.
Check that the valve spring seat contacts in the middle of the valve face with the width between 1.1 and 1.5 mm (0.043 and 0.059 in.).
| INSPECT INNER COMPRESSION SPRING |
Using vernier calipers, measure the free length of the inner compression spring.

- Free length:
- 45.46 mm (1.7898 in.)
Using a steel square, measure the deviation of the inner compression spring.

- Maximum deviation:
- 1.0 mm (0.039 in.)
- Maximum angle (reference):
- 2°
| INSPECT VALVE GUIDE BUSH OIL CLEARANCE |
Using a caliper gauge, measure the inside diameter of the valve guide bush.

- Bush inside diameter:
- 5.510 to 5.530 mm (0.2169 to 0.2177 in.)
Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.
- Standard clearance:
Item
Clearance
Intake
0.025 to 0.060 mm (0.0010 to 0.0024 in.)
Exhaust
0.030 to 0.065 mm (0.0012 to 0.0026 in.)
- Maximum oil clearance:
Item
Clearance
Intake
0.08 mm (0.0032 in.)
Exhaust
0.10 mm (0.0039 in.)
If the clearance is greater than the maximum, replace the intake valve and intake valve guide bush.
For exhaust side:
If the clearance is greater than the maximum, replace the exhaust valve and exhaust valve guide bush.
