2007-2013 Highlander Kluger · Service Manual RESTRAINTS

REMOVAL

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE REAR CENTER SEAT ASSEMBLY

4. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

5. REMOVE REAR SEAT TRACK BRACKET COVER LH

  1. B173775
    Disengage the 8 claws and remove the 2 rear seat track bracket covers.


6. REMOVE REAR OUTER TRACK BRACKET COVER LH

  1. B173776
    Disengage the 4 claws and remove the rear outer track bracket cover.


7. REMOVE REAR INNER TRACK BRACKET COVER LH

  1. B173777
    Disengage the 4 claws and remove the rear inner track bracket cover.


8. REMOVE REAR SEAT LEG SIDE COVER LH

  1. B173779
    Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.


9. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)

  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

    B180388E01

  1. B174594E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

    B173770E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    B180393E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.


10. REMOVE REAR NO. 1 SEAT ASSEMBLY LH

  1. B173780
    Remove the 3 bolts on the rear side of the seat.

  1. B173778
    Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


11. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

12. REMOVE REAR SEAT TRACK BRACKET COVER RH

  1. B173760
    Disengage the 8 claws and remove the 2 rear seat track bracket covers.


13. REMOVE REAR OUTER TRACK BRACKET COVER RH

  1. B173763
    Disengage the 4 claws and remove the rear outer track bracket cover.


14. REMOVE REAR INNER TRACK BRACKET COVER RH

  1. B173761
    Disengage the 4 claws and remove the rear inner track bracket cover.


15. REMOVE REAR SEAT LEG SIDE COVER RH

  1. B173765
    Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.


16. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

    B180390E01

  1. B173766E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

    B173768E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    B180392E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.


17. REMOVE REAR NO. 1 SEAT ASSEMBLY RH

  1. B173774
    Remove the 3 bolts on the rear side of the seat.

  1. B173764
    Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


18. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B173224
    Disengage the 8 claws and guide, and remove the front door scuff plate LH.


19. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173234
    Remove the front door opening trim weatherstrip LH.


20. REMOVE FRONT PILLAR GARNISH LH

  1. B173222E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish LH.

  1. Remove the clip <A>.

  1. B173225E01
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


21. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Remove the clip.

  1. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.


22. REMOVE REAR DOOR SCUFF PLATE LH

  1. B173228
    Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.


23. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173232
    Remove the rear door opening trim weatherstrip LH.


24. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


25. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


26. REMOVE FRONT PILLAR GARNISH RH

  1. B173682E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish RH.

  1. Remove the clip <A>.

  1. B173684E01
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


27. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


28. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


29. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


30. REMOVE LOWER CENTER PILLAR GARNISH LH

  1. B173230
    Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.


31. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

  1. B170910
    Remove the bolt and disconnect the floor end of the front seat outer belt assembly.


32. REMOVE CENTER PILLAR GARNISH LH

  1. B173229
    Remove the screw and clip.

  1. Disengage the 2 guides and clip, and remove the center pillar garnish LH.


33. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


34. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


35. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


36. REMOVE DECK BOARD ASSEMBLY

  1. B173240
    Remove the deck board assembly.


37. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Disengage the 2 guides and remove the No. 3 deck board sub-assembly.


38. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Disengage the 2 guides and remove the No. 2 deck board sub-assembly.


39. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover assembly.


40. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.


41. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Disengage the 2 clips and remove the rear seat side cover LH.


42. REMOVE DECK SIDE TRIM BOX LH

  1. B173243E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box LH as shown in the illustration.

    B178554


43. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Disengage the 2 clips and remove the rear seat side cover RH.


44. REMOVE JACK CARRIER SUPPORT

45. REMOVE JACK CARRIER CUSHION (for LHD)

  1. B178550
    Remove the jack carrier cushion.


46. REMOVE JACK CARRIER CUSHION (for RHD)

  1. B178551
    Remove the jack carrier cushion.


47. REMOVE JACK ASSEMBLY (for LHD)

  1. B173245
    Remove the jack assembly.


48. REMOVE JACK ASSEMBLY (for RHD)

  1. B178566
    Remove the jack assembly.


49. REMOVE JACK CARRIER ASSEMBLY (for LHD)

  1. B178548
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


50. REMOVE JACK CARRIER ASSEMBLY (for RHD)

  1. B179785
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


51. REMOVE DECK SIDE TRIM BOX RH

  1. B173247E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box RH as shown in the illustration.

    B178552


52. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178560
    Remove the 4 bolts and 4 nuts.

  1. Remove the deck floor board assembly.


53. REMOVE REAR MAT

  1. B173249
    Remove the rear mat.


54. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B178561
    Disengage the 3 claws.

  1. Remove the 2 nuts and the deck floor board assembly.


55. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Remove the 2 nuts and the deck floor box.


56. REMOVE NO. 1 DECK BOARD (w/o Rear No. 2 Seat)

  1. B178558
    Disengage the 3 clips and remove the rear floor board spacer from No. 1 deck board.


57. REMOVE NO. 1 DECK BOARD (w/ Rear No. 2 Seat)

  1. B178556
    Disengage the 5 clips and remove the rear deck floor box from the No. 1 deck board.


58. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B170935
    Remove the bolt and rear No. 2 seat inner belt assembly.

    HINT:
    Use the same procedure for the RH side and LH side.


59. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

  1. B170936
    Remove the bolt and disconnect the rear seat lap type belt assembly LH.


60. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and LH side (Click here).


61. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B173781
    Remove the 4 bolts and the rear No. 2 seat assembly.


62. REMOVE REAR FLOOR FINISH PLATE

  1. B173609
    Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.


63. REMOVE DECK SIDE TRIM COVER NO.2

  1. B173595E01
    Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

    HINT:
    Tape the screwdriver tip before use.


64. REMOVE DECK SIDE TRIM LH

  1. B173596
    Remove the bolt.

  1. B173623
    Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.


65. REMOVE SIDE TRIM COVER LH

  1. B173597
    Disengage the 10 claws and remove the side trim cover LH.


66. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH

  1. B173611E01
    Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

    HINT:
    Tape the screwdriver tip before use.


67. REMOVE REAR POWER POINT SOCKET ASSEMBLY
  1. Disconnect the connector.

  1. E151327
    Disengage the claw and remove the rear power point socket assembly.


68. REMOVE REAR POWER OUTLET SOCKET COVER

  1. E151328
    Disengage the 2 claws and remove the rear power outlet socket cover.


69. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)

  1. B173602
    Disengage the 10 claws and remove the rear deck trim cover.


70. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)

  1. B173603
    Disengage the 5 claws and remove the reclining remote control bezel LH.


71. REMOVE ROPE HOOK ASSEMBLY (for LH Side)

  1. B173598E01
    for Front Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.

  1. B173600E01
    for Rear Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and rope hook assembly.


72. REMOVE NO. 2 DECK SIDE TRIM HOOK

  1. B173612
    Remove the screw and the No. 2 deck side trim hook.


73. REMOVE FRONT DECK SIDE TRIM COVER LH

  1. B173604E01
    Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

    HINT:
    Tape the screwdriver tip before use.


74. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

  1. B170933
    Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.


75. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Remove the 2 bolts.

  1. Remove the 2 clips.

  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

    B173613


76. REMOVE QUARTER PILLAR GARNISH LH

  1. B175156
    Disengage the 2 claws and 2 guides, and remove the No. 1 seat outer belt guide.

  1. B173263
    Disengage the 2 clips and the 2 guides, and remove the quarter pillar garnish LH.


77. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)

  1. w/o Rear No. 2 Seat:

    1. B173268
      Remove the bolt.

    2. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

  1. w/ Rear No. 2 Seat:

    1. B175157
      Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.

    2. B173267
      Remove the bolt.

    3. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.


78. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)

  1. w/o Rear No. 2 Seat:

    1. B173266
      Remove the bolt.

    2. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

  1. w/ Rear No. 2 Seat:

    1. B175157
      Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.

    2. B173265
      Remove the bolt.

    3. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.


79. REMOVE REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)

  1. B173614
    Disengage the 8 claws and guide, and remove the rear seat side garnish cap.


80. REMOVE REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)

  1. B173616
    Remove the screw.

  1. Disengage the 6 claws and the guide, and remove the rear seat side garnish cap.


81. REMOVE DECK SIDE TRIM COVER NO.1

HINT:
Use the same procedure for the RH side and LH side (Click here).


82. REMOVE DECK SIDE TRIM RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


83. REMOVE SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)

  1. B173610
    Disengage the 4 claws and remove the side trim cover RH.


84. REMOVE REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System)

  1. E150364
    Disengage the 4 claws and remove the rear room temperature sensor.

  1. Disconnect the connector.


85. REMOVE REAR COMBINATION LIGHT SERVICE COVER RH

  1. B173618E01
    Using a screwdriver, disengage the 6 claws and the 2 guides, and remove the rear combination light service cover RH.

    HINT:
    Tape the screwdriver tip before use.


86. REMOVE ROPE HOOK ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and LH side (Click here).


87. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook (Click here).


88. REMOVE FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


89. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


90. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Remove the 3 bolts.

  1. Remove the 2 clips.

  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.

    B173622


91. REMOVE QUARTER PILLAR GARNISH RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


92. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and LH side (Click here).


93. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and LH side (Click here).


94. REMOVE ROOF CONSOLE BOX ASSEMBLY

  1. B173250
    Using a moulding remover, disengage the 2 clips, 3 guides and fastener.

  1. Disconnect the connector and remove the roof console box assembly.


95. REMOVE VISOR BRACKET COVER (for LH Side)

  1. B132069
    Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.


96. REMOVE VISOR ASSEMBLY LH

  1. B173261
    Remove the 2 screws and remove the visor assembly LH.


97. REMOVE VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure for the RH side and LH side (Click here).


98. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and LH side (Click here).


99. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

  1. B175048E01
    Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.

  1. B175049
    Disengage the 2 claws and remove the inner rear view mirror stay holder cover.


100. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Standard)

  1. B132140E02
    Using a screwdriver, disengage the 4 claws and remove the lens cover.

    HINT:
    Tape the screwdriver tip before use.

  1. B132142E01
    Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the 2 claws <B>.

  1. B153052
    Using a screwdriver, disengage the 4 claws and remove the No. 1 room light assembly.


101. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Independent Type)

  1. B173252E01
    Using a screwdriver, disengage the 4 claws and remove the lens cover.

    HINT:
    Tape the screwdriver tip before use.

  1. B173254E01
    Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the 2 claws <B>.

  1. B173256
    Using a screwdriver, disengage the 8 claws and remove the No. 1 room light assembly.


102. REMOVE NO. 2 ROOM LIGHT ASSEMBLY

  1. B132140E02
    Using a screwdriver, disengage the 4 claws and remove the lens cover.

    HINT:
    Tape the screwdriver tip before use.

  1. B132142E01
    Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

    HINT:
    Tape the screwdriver tip before use.

  1. Disengage the 2 claws <B>.

  1. B153052
    Using a screwdriver, disengage the 4 claws and remove the No. 2 room light assembly.


103. REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)

  1. E150581
    Disengage the 4 clips and remove the television base.


104. REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)
  1. Disconnect the connector.

  1. E150582
    Remove the 4 bolts.

  1. E150583
    Disengage the 2 clips and 2 claws, and then remove the television display.


105. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

  1. B153056E01
    Using a clip remover, disengage the 4 claws.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    1. Gently pry on the assist grip covers as shown in the illustration to remove them.
    2. Tape the clip remover tip before use.

  1. B153057
    Pull off the 2 assist grip covers by hand.

  1. Disengage the 2 clips and remove the front assist grip sub-assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the RH side and the LH side.


106. REMOVE REAR ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

  1. B167235E01
    Using a clip remover, disengage the 4 claws.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    1. Gently pry on the assist grip covers as shown in the illustration to remove them.
    2. Tape the clip remover tip before use.

  1. Pull off the 2 assist grip covers by hand.

  1. B167236
    Disengage the 2 clips and remove the rear assist grip sub-assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the RH side and the LH side.


107. REMOVE ASSIST GRIP ASSEMBLY (w/ Sliding Roof)

  1. B173257E01
    Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    Tape the screwdriver tip before use.

  1. B173258
    Disengage the 4 clips and remove the assist grip assembly.

  1. Remove the 4 clips from the vehicle body.

    HINT:
    Use the same procedure for the other 4 assist grips.


108. REMOVE ROOF HEADLINING TRIM CLIP STOPPER

  1. B173593E01
    Using a screwdriver, disengage the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the bolt and the roof headlining trim clip stopper.

    HINT:
    Use the same procedure for the RH side and the LH side.


109. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

110. REMOVE VISOR HOLDER

  1. B151362E01
    Turn the visor holder approximately 45° and pull it out as shown in the illustration.

  1. Disengage the 2 claws and remove the visor holder.

    HINT:
    Use the same procedure for the RH side and the LH side.


111. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
  1. Disconnect the No. 1 roof wire connector and disengage the 3 clamps from the front pillar LH.

  1. Disconnect the No. 2 antenna cord sub-assembly connector, disengage the 3 clamps, and remove the bolt from the front pillar RH.

  1. Disconnect the No. 2 antenna cord sub-assembly connector from the rear pillar RH.

  1. Remove the 4 clips.

    B173270E01

  1. B173272
    Remove the roof headlining assembly from the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.


112. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
  1. Disconnect the No. 1 roof wire connectors and disengage the 3 clamps from the front pillar LH.

  1. w/ Rear Seat Entertainment System:

    1. Disconnect the No. 1 roof wire connector from the rear pillar LH.

  1. Disconnect the No. 2 antenna cord sub-assembly connector, disengage the 3 clamps and remove the bolt from the front pillar RH.

  1. Disconnect the No. 2 antenna cord sub-assembly connector from the rear pillar RH.

  1. Disconnect the sliding roof drive gear connector.

  1. Remove the 3 clips.

    B173269E01

  1. B173273
    Remove the roof headlining assembly from the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or body interior.


113. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY
  1. Disconnect the curtain shield airbag connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the 11 bolts .

    C166976

  1. Disengage the 11 hooks and remove the curtain shield airbag assembly.

    C168037

← REMOVAL (May 2007 – Jul 2008)REMOVAL (from Jul 2010) →