2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

Air Conditioning Compressor Magnetic Clutch Circuit

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the A/C amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the A/C amplifier. Then, the MGC relay turns on to operate the magnetic clutch.

WIRING DIAGRAM

E154312E02

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Turn the A/C switch on and off.

  1. Select the item below in the Data List, and read the display on the intelligent tester.

    Data List / Engine: 
    Tester Display
    Measure Item/Range
    Normal Condition
    Diagnostic Note
    A/C Signal
    (A/C Signal)
    A/C signal / ON or OFF
    ON: A/C ON
    OFF: A/C OFF
    -

    OK:
    The display is as specified in the normal condition column.



NG
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


2. INSPECT FUSE (A/C NO. 2)
  1. Remove the A/C NO. 2 fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A/C NO. 2
    Always
    Below 1 Ω



NG
REPLACE FUSE (A/C NO. 2)
OK


3. INSPECT MAGNET-CLUTCH RELAY (MG CLT)

  1. B060778E04
    Remove the MG CLT relay from the engine room No. 1 relay block and junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE MAGNET-CLUTCH RELAY (MG CLT)
OK


4. CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - BATTERY)

  1. E143742E94
    Disconnect the connector from the air conditioning amplifier.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D33-20 (MGC) - Body ground
    Ignition switch off
    Below 1 V
    D33-20 (MGC) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT AIR CONDITIONING AMPLIFIER

  1. E124471E47
    Reconnect the connector to the air conditioning amplifier.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D33-20 (MGC) - Body ground
    Ignition switch on (IG)
    Air conditioning switch: OFF
    11 to 14 V
    D33-20 (MGC) - Body ground
    Ignition switch on (IG)
    Air conditioning switch: ON
    Below 1 V



NG
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
OK


6. INSPECT A/C COMPRESSOR

  1. E152688E08
    Disconnect the connector from the air conditioning compressor.

  1. Measure the resistance of the connector.

  1. When connector terminal 1 (MG+) is connected to the positive (+) battery terminal, and the body ground is connected to the negative (-) battery terminal, check that the following occurs: 1) the magnetic clutch's operating sound is emitted, and 2) the magnetic clutch's hub and rotor lock.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B44-1 (MG+) - Body ground
    Always
    Below 1 Ω



NG
REPLACE AIR CONDITIONING COMPRESSOR
OK


7. CHECK HARNESS AND CONNECTOR (ENGINE ROOM R/B AND J/B - BATTERY)

  1. E155266E01
    Remove the MG CLT relay from the engine room No. 1 relay block and junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Relay block MG CLT relay terminal 5 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    Relay block MG CLT relay terminal 1 - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM R/B AND J/B - BATTERY)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM R/B AND J/B - A/C COMPRESSOR)


← Heater Control Panel Power Source Circuit (from May 2007)Air Conditioning Compressor Magnetic Clutch Circuit (Aug 2008 – Jun 2010) →