When the A/C amplifier is turned on, a magnetic clutch ON signal is sent from the MGC terminal of the A/C amplifier. Then, the MG/CLT relay turns on to operate the magnetic clutch.
WIRING DIAGRAM
INSPECTION PROCEDURE
1. READ VALUE USING INTELLIGENT TESTER
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Turn the A/C switch on and off.
Select the item below in the Data List, and read the display on the intelligent tester.
Data List / Engine:
Tester Display
Measure Item/Range
Normal Condition
Diagnostic Note
A/C Signal (A/C Signal)
A/C signal / ON or OFF
ON: A/C ON OFF: A/C OFF
-
OK:
The display is as specified in the normal condition column.
NG
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK
2. INSPECT FUSE (A/C NO. 2)
Remove the A/C NO. 2 fuse from the instrument panel junction block.
Measure the resistance of the fuse.
Standard resistance:
Tester Connection
Condition
Specified Condition
A/C NO. 2 fuse
Always
Below 1 Ω
NG
REPLACE FUSE (A/C NO. 2)
OK
3. INSPECT MAGNET-CLUTCH RELAY (MG/CLT)
Remove the MG/CLT relay from the engine room relay block and junction block.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is applied to terminals 1 and 2
Below 1 Ω
NG
REPLACE MAGNET-CLUTCH RELAY (MG/CLT)
OK
4. CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - BATTERY)
Disconnect the connector from the air conditioning amplifier.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Condition
Specified Condition
D33-20 (MGC) - Body ground
Ignition switch off
Below 1 V
D33-20 (MGC) - Body ground
Ignition switch on (IG)
11 to 14 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
5. INSPECT AIR CONDITIONING AMPLIFIER
Reconnect the connector to the air conditioning amplifier.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Condition
Specified Condition
D33-20 (MGC) - Body ground
Ignition switch on (IG) Air conditioning switch: OFF
11 to 14 V
D33-20 (MGC) - Body ground
Ignition switch on (IG) Air conditioning switch: ON
Disconnect the connector from the compressor and magnetic clutch.
Measure the resistance of the connector.
When connector terminal 3 (MG+) is connected to the positive (+) battery terminal, and the body ground is connected to the negative (-) battery terminal, check that the following occurs: 1) the magnetic clutch's operating sound is emitted, and 2) the magnetic clutch's hub and rotor lock.
Standard resistance:
Tester Connection
Condition
Specified Condition
B52-3 (MG+) - Body ground
Always
Below 1 Ω
NG
REPLACE COMPRESSOR AND MAGNETIC CLUTCH (Click here)
OK
7. CHECK HARNESS AND CONNECTOR (ENGINE ROOM R/B AND J/B - BATTERY)
Remove the MG/CLT relay from the engine room relay block and junction block.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Condition
Specified Condition
Relay block MG/CLT relay terminal 5 - Body ground
Ignition switch on (IG)
11 to 14 V
Relay block MG/CLT relay terminal 1 - Body ground
Ignition switch on (IG)
11 to 14 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM R/B AND J/B - BATTERY)
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM R/B AND J/B - A/C COMPRESSOR)