2007-2013 Highlander Kluger · Service Manual BRAKE

C1210 Zero Point Calibration of Yaw Rate Sensor Undone

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor via the CAN communication system.
The yaw rate sensor has a built-in acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTCs U0123 (yaw rate sensor communication trouble) and U0124 (acceleration sensor communication trouble) are output.
The DTCs are also output when the calibration has not been completed.
DTC Code
DTC Detection Condition
Trouble Area
C1210
Zero point calibration of yaw rate sensor undone.
Yaw rate and acceleration sensor
C1336
Zero point calibration of acceleration sensor undone.
Yaw rate and acceleration sensor

WIRING DIAGRAM

Refer to DTCs C1232, C1243 and C1245 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly or yaw rate and acceleration sensor, perform zero point calibration (Click here).

HINT:
When U0123, U0124 and/or U0126 is output together with C1210 and/or C1336, inspect and repair the trouble areas indicated by U0123, U0124 and/or U0126 first (Click here).


1. PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
  1. Perform zero point calibration of the yaw rate and acceleration sensor (Click here).


NEXT


2. PERFORM TEST MODE (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the sensor check in the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are erased.

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
Go to step 3
OK

END

3. CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
  1. Turn the ignition switch off.

  1. Check that the yaw rate and acceleration sensor has been installed properly (Click here).

    OK:
    The sensor should be tightened to the specified torque.
    The sensor should not be installed in a tilted position.



NG
INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY (Click here)
OK


4. READ VALUE ON INTELLIGENT TESTER (YAW RATE AND ACCELERATION SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Deceleration Sensor
    Acceleration sensor / min.: -18.525 m/s2, max.: 18.387 m/s2
    Min.: -18.525 m/s2
    Max.: 18.387 m/s2
    Reading changes when vehicle is bounced
    Deceleration Sensor2
    Acceleration sensor 2 / min.: -18.525 m/s2, max.: 18.387 m/s2
    Min.: -18.525 m/s2
    Max.: 18.387 m/s2
    Reading changes when vehicle is bounced
    Yaw Rate Sensor
    Yaw rate sensor / min.: -128 °/s, max.: 127 °/s
    Vehicle stationary: 0 °/s
    Right turn: -128 to 0 °/s
    Left turn: 0 to 127 °/s
    -
    Yaw Rate Sensor2
    Yaw rate sensor 2 / min.: -128 °/s, max.: 127 °/s
    Vehicle stationary: 0 °/s
    Right turn: -128 to 0 °/s
    Left turn: 0 to 127 °/s
    -

  1. Check that the yaw rate and acceleration sensor output value displayed on the intelligent tester.

    OK:
    The yaw rate and acceleration sensor output value is normal.

    NOTICE:
    Check the yaw rate and acceleration sensor signal after replacement (Click here).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPLACE YAW RATE AND ACCELERATION SENSOR (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← C1210 Zero Point Calibration of Yaw Rate Sensor Undone (+ C1336) (Aug 2008 – Jun 2010)C1232 Acceleration Sensor Stuck Malfunction (+ C1243, C1245) (May 2007 – Jul 2008) →