2007-2013 Highlander Kluger · Service Manual BRAKE

C1434 Steering Angle Sensor Output Malfunction

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

Steering angle sensor signals are sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it will be detected by the steering angle sensor zero point malfunction diagnostic function.
DTC Code
DTC Detection Condition
Trouble Area
C1434
Error in communication between the skid control ECU and the steering angle sensor, or abnormal steering angle sensor zero point.
  1. Steering angle sensor power supply
  2. Steering angle sensor
  3. Brake actuator assembly (Skid control ECU)

WIRING DIAGRAM

Refer to DTC C1432 (Click here).

INSPECTION PROCEDURE

HINT:
  1. When U0073, U0123, U0124 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0123, U01245 and/or U0126 first (Click here).
  2. When any of the speed sensors or the yaw rate and acceleration sensor has trouble, DTCs for the steering angle sensor may be output even when the steering angle sensor is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor.


1. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG) again and check that no CAN communication system DTC is output (Click here).

  1. Start the engine.

  1. Drive the vehicle and turn the steering wheel to the right and left at a speed of 35 km/h (22 mph) and check that no speed sensor or yaw rate and acceleration sensor DTCs are output (Click here).

    Result:
    Result
    Proceed to
    No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output
    A
    CAN communication system DTC is output
    B
    Speed sensor or yaw rate and acceleration sensor DTC is output
    C

    HINT:
    1. If there is a malfunction in any of the speed sensors or the yaw rate and acceleration sensor, an abnormal value may be output although the steering angle sensor is normal.
    2. If speed sensor and yaw rate and acceleration sensor DTCs are output simultaneously, repair these two sensors first and inspect the steering angle sensor.



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)

C
REPAIR CIRCUIT INDICATED BY OUTPUT DTC (Click here)
A


2. INSPECT STEERING ANGLE SENSOR (POWER SOURCE TERMINAL)

  1. C156493E10
    Turn the ignition switch off.

  1. Remove the steering wheel and the column cover lower.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the steering angle sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D13-4 (IG1) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    D13-5 (BAT) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


3. INSPECT STEERING ANGLE SENSOR (GROUND TERMINAL)

  1. C156493E11
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D13-1 (ESS) - Body ground
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)
OK

REPLACE STEERING ANGLE SENSOR (Click here)


← C1434 Steering Angle Sensor Output Malfunction (May 2007 – Jul 2008)C1434 Steering Angle Sensor Output Malfunction (Jul 2010 – Jun 2012) →