DTC CHECK / CLEAR
Troubleshooting · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| DTC CHECK/CLEAR (When Using Intelligent Tester) |
Check for DTCs.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Read the DTCs following the prompts on the tester screen. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.
Check the details of the DTCs (Click here).
Clear the DTCs.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Operate the intelligent tester to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC / DTC / Clear.
| DTC CHECK/CLEAR (When not Using Intelligent Tester) |
Check for DTCs.
Using SST, connect terminals TC and CG of the DLC3.

- SST
- 09843-18040
Turn the ignition switch on (IG).
Observe the blinking pattern of the ABS warning and slip indicator lights in order to identify the DTC.
- HINT:
- If no code appears, inspect the TC and CG terminal circuit, and ABS warning and slip indicator light circuits.
Trouble Area
See procedure
TC and CG terminal circuit
Click here
ABS warning light circuit (Remains on)
Click here
ABS warning light circuit (Does not come on)
Click here
Slip indicator light circuit (Remains on)
Click here
Slip indicator light circuit (Does not come on)
Click here
As an example, the illustration below shows the blinking patterns of the normal system code and trouble codes 11 and 21 for the ABS warning and slip indicator lights.


Check the details of the DTCs.
DTC chart for ABS: Warning Light Display
Intelligent Tester Display
11
C0278
12
C0279
13
C0273
14
C0274
21
C0226
22
C0236
23
C0246
24
C0256
25
C1225
31
C1401
C1405
32
C1402
C1406
33
C1403
C1407
34
C1404
C1408
35
C1413
36
C1414
37
C1337
38
C1415
39
C1416
41
C1241
C1417
43
C1243
44
C1419
C1420
C1442
45
C1245
46
C1421
C1422
C1423
C1424
49
C1425
C1426
51
C1427
C1428
67
C1429
C1430
C1431
91
C1361
94
U0073
95
U0124
97
C1381
(*1): This DTC is output when the VSC system detects a malfunction in the ABS.DTC chart for VSC: Indicator Light Display
Intelligent Tester Display
31
C1432
C1433
C1434
32
C1232
34
C1435
C1436
C1443
36
C1210
39
C1336
43 (*1)
-
51
C1201
53
C1203
62
U0123
63
U0126
64
C1380
65
C1437
U0100
66
C1290
C1439
C1445
98
C1440
C1441
After completing the check, disconnect terminals TC and CG of the DLC3 to turn off the display.
If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.
Clear the DTCs.
Using SST, connect terminals TC and CG of the DLC3.

- SST
- 09843-18040
Turn the ignition switch on (IG).
Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

Check that the warning light indicates a normal system code.
Remove SST from the terminals of the DLC3.
- HINT:
- Clearing the DTCs cannot be performed by disconnecting the battery terminal or the ECU-IG NO. 2 fuse.
| END OF DTC CHECK/CLEAR |
Turn the ignition switch on (IG).
Check that the ABS warning and slip indicator lights go off within approximately 3 seconds after turning the ignition switch on (IG).